V-tech vt9118 User manual

Parts Check List:
1. Handset
2. Base Unit
3. Telephone line cord
4. BatteryPack
5. AC adapter
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).
5. Do not place this product on an unstable cart, stand, or table.The product may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation.To protect it from overheating, these
openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. This product should not be placed in a built-in-installation where
proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking
on it.
9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short
out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
10.To reduce the risk of electric shock, do not disassemble this product. If service or repair work is required, contact VTech
Customer Service at 1-800-595-9511. Opening or removing cabinet parts other than specified access doors may expose
youto dangerousvoltages orother risks.Incorrect reassembling can cause electricshock when the appliance issubsequently
used.
11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
12.Unplug this product from the wall outlet:
a) When the power supply cord or plug is damaged or frayed.
b) If liquid has been spilled into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustment of other controls may result in damage and will often require
extensive work to restore the product to normal operation.
e) If the product has been dropped and the cabinet has been damaged.
f) If the product exhibits a distinct change in performance.
13.Avoid using a telephone (other than a cordless type) during an electrical storm.There may be a remote risk of electric shock
fromlighting.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVETHESE INSTRUCTIONS
1. Slide the battery cover off by gently pressing
onthe recessed area with adownward motion.
2. Unplugand removethe oldbattery pack.Don't
put the old battery pack in a trash compactor
or a fire - it could burst.
3. Plug in the replacement battery pack. Place
the battery pack in the compartment with the
battery cord resting on top of it.
4. Replace the battery cover by sliding it into
place.
5. Thenew batterypack must be charged before
usingyour telephone.Place thehandset inthe
cradle of the base unit to allow it to charge for
16 hours. Maximum battery life between
charges is more than 5 hours of continuous
talk time or 6 days of standby.
CAUTION: Toreduce theriskof fireorinjury,read
and follow these instructions:
INTRUDUCTION
To purchase replacement battery packs, call
VTECH Communications at 1-800-595-9511.
In Canada, call VTECH Electronics at 1-800-
267-7377.
IMPORTANT SAFETY INSTRUCTIONS REPLACINGTHE HANDSET BATTERIES
1. Useonly VTECHbattery (80-5074-00-00).
2. Do not open or mutilate the battery.Released electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
3. Exercise care in handling batteries in order not to short the battery with conducting materials such as
rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
4. Do not dispose of the battery in a fire.The cell may explode.
The RBRC™ Seal
The RBRC®Sealon the nickel-cadmiumbattery indicatesthatVTech Communications,Inc.isvoluntarily
participating in an industry program to collect and recycle these batteries at the end of their
useful lives, when taken out of service within the United States and Canada.
TheRBRC®program provides a convenient alternative toplacing usednickel-cadmium batteries
into the trash or municipal waste, which may be illegal in your area.
VTech’s participation with RBRC®makes it easy for you to drop off the spent battery at local
retailersparticipating inthe RBRC®programor at authorizedVTech product servicecenters.Please call 1-
800-8-BATTERY™forinformationon Ni-Cd battery recycling and disposalbans / restrictions inyourarea.
VTech’sinvolvementin thisprogramis part ofits commitmentto protectingour environmentandconserving
naturalresources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
1
23

Setting UpYour VT9118
1. Choose an area near an electrical outlet and a telephone wall jack.
2. Plug the AC power adapter into an electrical outlet and the DC connector to the back of the
base unit.
CAUTION: Use only the AC adapter shipped with your VT9118.It is specifically designed for this
product.
NOTE: Connect power to the base unit before placing the handset in the cradle.
3. CHARGETHE HANDSET BATTERYPACKBEFORE USE.The batteries rechargeautomatically
whenever the handset is in the base unit cradle.The batteries must be charged for 16 hours
before using your phone for the first time.
4. Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the
rear of the base unit. Plug the other end into a telephone wall jack. Make sure the plugs snap
securely into place.
5. CHECK FOR A DIAL TONE. After the batteries are charged, pick up the handset and press
the PHONE key.The IN USE indicator should light up, and you should hear a dial tone.If not,
see IN CASE OF DIFFICULTY.
CAUTION:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
1.Choosea spot nearan electrical outletanda telephone jack.Your phone requiresamodular
telephone jack and a standard electrical outlet (120V AC).The power cord is six feet long;
make sure there is an electrical outlet within reach of the base.The outlet should not be
controlled by a wall switch. If the switch is ever turned off, the phone will not operate.
2.Mount the base on the wall. Positionthe base so the mountingstudswill fit into theholesat
the back of the base. Position the power cord to extend down the wall the phone is to be
mountedon. Slide the base downon the mounting studsuntil it locks intoplace.
3.Connect the telephone cord.The telephone line cordhasasnap-in plug at each end.Insert
oneofthe plugs into the jackonthebottomofthe base.Insert the other end of the plug into the
wall jack.
4.Connect the power cord. Plugthe DC connector into the DC jack at the rearofthebaseunit.
Plugthe AC power adapterinto an electrical outlet.
PHONE LED
• The PHONE LED lights when the handset
is on an active call.
• Itflashesin cadence with an incoming ring.
• It flashes quickly during PROG mode.
• It flashes slowly when battery is low.
PHONE KEY/ FLASH KEY
• Press the PHONE key to make a call.
• If you are currently on a call, pressing
PHONE flashesthe line.This wouldbe used
with a feature like call waiting to answer
your second call.
PROG KEY
• Press PROG key to enter PROGRAM
mode. See Programming Speed Dial
Numbers for more details.
VOLUME CONTROL
• Thereare 3 volumelevels:LOW;MEDIUM;
HIGH.
• While on a call, press the Up or Down key
REPLACEMENT BATTERY ORDER FORM
ForVT 9118 CordlessTelephone
Name: Adress:
City: State: Zip:
DaytimePhone Number:( )
ORDER INFORMATION
ForModel VT 9118
(QTY.) Batteries @$19.95 each ................................................. $
Shipping/Handling @$ 4.95 per battery ....................................................... $
METHOD OF PAYMENT: DO NOT SEND CASH
CHECK/M.O. VISA MASTERCARD DISCOVER AMERICAN EXPRESS
Credit Card# EXP. DATE
CARD HOLDER’S SIGNATURE
PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:
VTECH COMMUNICATIONS INC.
8770 SW NIMBUS AVENUE
BEAVERTON, OREGON 97008-7195 USA
YOUMAYALSO ORDERBYPHONE.CALL1-800-595-9511
GETTTING STARTED WALL MOUNTING
HANDSET FEATURES BASE UNIT FEATURES
toadjustthe listening volume.The Handset
willemit a double beep when the maximum
or minimum volume level has been
reached.
OFF KEY
• Press the OFF key to exit all modes of
operation.
REDIAL / PAUSE KEY
• When you hear the dial tone, pressing the
REDIAL key will dial out the last number
that wascalled on your phone.
• Itcanalsobeusedtostorethelastnumber
dialed into the speed dial memory. See
Storing a Redial Number into Speed Dial
for details.
• You can store a PAUSE into your dialing
number. See Storing Pauses in Memory
for detail.
CHAN KEY
• Pressing the CHAN key when the handset
is in use will activate a channel change to
the next free channel.
• This is used if you are experiencing noise
or interference on the current channel.
MEM KEY
• Press the MEM key to enter MEMORY
mode.
• The sequence for dialing out a speed dial
number in memory is: PHONE, MEM,
Number Button (0-9).
TONE/ *KEY
• In PULSE dialing mode, this key is used to
switch to Temporary TONE dialing mode.
IN USE/CHARGE LED
• The LED illuminates steadily when the
handset is in the base cradle to indicate
that the handset battery is being charged.
• TheLEDilluminates whenever the handset
is being used.
• This LED also flashes with the cadence of
the incoming ring.
PAGE KEY
• Press the PAGE key to page the handset.
• Press it second time to cancel a page.
• The base will ring the handset 1 minute
before ending the page automatically.
• The handset can also cancel the page by
pressing the OFF key.
45
6
7

Making Calls
Pickup the handset and press PHONE.When
you hear a dial tone, dial the number. The
PHONE LED will illuminate while the Handset
is in use.
Ifyou make a mistake when dialing, pressOFF
to hang up, then press PHONE to get the dial
tone again.
You must alwayspress PHONEbeforeyoucan
dial a call on the handset.
Answering Calls
When an incoming call is ringing, the IN USE
LED on the base and PHONE LED on the
handset will flash. To make sure your phone
ringswhenthe handset is away from the base,
please keep the base antenna in the upright
position.
TONE/PULSE Setting
If you have touch tone service on phone line.
Press PROG, * , *, MEM to switch to TONE
dialing. If you have rotary service, press
PROG, * , # ,MEM to switch to PULSE.
NOTE: Your VT9118 is preset at the factory
for TONE dialing.
TemporaryTone
If you have a rotary (dial-pulse) telephone
service, (TONE/PULSE setting is set to
PULSE), this feature allows you to enter
special codes and tones to operate answering
machines, use electronic banking services,
calling cards, or other special services.
First, dial the call normally.Then activate the
Temporary Tone feature by pressing TONE
(the * key).You can then press the numbers
orsymbols you need, and your phonewillsend
the proper signals.
To end the call,press OFF or place the handset
back in the base.The phone will automatically
go back to rotary (dial-pulse) service.
ProgrammingThe RingerType
The handset ringer is capable of four different
types of ringing tones.The following sections
detail how to change the different tones and
to turn off a ringer on the handset.
To program, the handset must be OFF.
To select a different ringer type do the
following:
• PressPROG
• Press the #key.
• Press a key 1..4 to select a ringer type.
• Press the MEM key to confirm.
4. Press MEM to store the phone number to
the key you selected.
The phone now exits PROG mode and emits
a tone.
Speed Number Dialing
1. Press PHONE to get a dial tone.
2. Press MEM and the memory location
number key (0-9).
For example, to dial the number you assigned
to key '8', you would press PHONE, MEM, 8.
To Change or Replace a Speed Dial
Number
To change or replace a stored number in
speed dial memory simply enter the new
number and store it in the memory location
you wish to change.
For example, to change the number stored in
memory position 7 to 555-1111, you would
press PROG, 7, 555-1111, MEM.
Storing Pauses in Memory
To insert a pause in a phone number, press
PAUSE.The pause is 2 seconds in length.For
longer pauses, press PAUSE two or more
times. Each additional press indicates an
additional 2 second pause.
If your phone is connected to a PBX you can
store the PBX access number and a pause
before the phone number. For example, to
store 9-PAUSE-555-1234 in memory location
8 do the following:
If you have difficulty operating your phone, the
suggestions below should solve the problem. If you
still have difficulty after trying these suggestions,
In the US Call:
VTECH Communications at
1-800-595-9511.
In Canada Call:
VTECH Electronics at
1-800-267-7377.
THE PHONE DOESN'T WORK AT ALL.
• Make sure the power cord is plugged in.
• Make sure the telephone line cord is plugged firmly
into the base unit and the telephone wall jack.
• Make sure the batteries are properly charged. If
the handset makes two beeps, the batteries need
charging. If the IN USE indicators do not light when
you press PHONE, you must charge the batteries.
• If you recently installed a new battery pack, make
sure it is installed correctly.
NO DIAL TONE.
• First check all the suggestions above.
• If you still don't hear a dial tone, disconnect the
base unit from the telephone jack and connect a
different phone. If there is no dial tone on that
phone either, the problem is in your wiring or local
service. Call your local telephone company.
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
EVEN WHEN YOU'RE NEAR THE BASE UNIT.
Household appliances plugged into the same circuit
as the base unit can sometimes cause interference.
Try moving the appliance or the base unit to another
outlet.
YOU GET NOISE, STATIC, OR A WEAK SIGNAL
WHEN YOU'RE AWAY FROM THE BASE UNIT.
• You may be out of range.Either move closer to the
base, or relocate the base unit.
• The layout of your home may be limiting the range.
Try moving the base unit to the second or third
floor, or to some other location.
THE HANDSET DOES NOT RING WHEN YOU
RECEIVE A CALL.
• Ensure that the ringer is turned on.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
IN CASE OF DIFFICULTYOPERATING INSTRUCTIONS
To answer a call when the handset is in the
base, just pick up the handset.
To answer a call when the handset is away
from the base, just press any key on the
handset (except OFF).This is very useful in a
dark environment; you do not have to fumble
around looking for the PHONE key to answer
the call.
Disconnecting
To end a call, either place the handset back in
the base, or press OFF on the handset.
Changing Channels
If you notice interference when using your
handset, press CHAN to switch to a clear
channel. This function is only available when
you are on a call.
Turning OffThe Ringer
To turn off the ringer on the handset, do the
following:
• Press PROG
• Press the #key
• Press 5to turn off the ringer
• Press the MEM key to confirm
• To turn the ringer on again, see
Programming the Ringer Type.
CheckingThe Ringer
To check the ringer which is currently
programmed, do the following:
• Press PROG
• Press the #key
• Press 0
• Press the MEM key to confirm
Memory Dialing
The VT9118 canstore up to 10 differentphone
numbers that you can dial just by pressing
phone, MEM and one of the number keys (0-
9).
Programming Speed Dial Numbers
The handset must be OFF.
1. Press PROG.ThePHONE LED will blink to
indicate that you are in the programming
mode.
2. Press the number of the memory location
you wish to store the number in (0-9).
3. Using the dial pad, dial the number you
want to store.The number can be up to 16
digits long. The number can be entered
manually or by using REDIAL.
1. Press PROG
2. Press 8
3. Press 9
4. Press REDIAL / PAUSE
5. Dial 555-1234
6. Press MEM
Using REDIAL
To REDIAL the last number you called, press
PHONE then press REDIAL. The phone will
automatically dial the number.
Storing a Redial Number into Speed Dial
Tostore the last number youdialed as a Speed
Dial number, press PROG, a location number
(0-9), REDIAL, MEM.
The Page Feature
From the base unit, press PAGE to signal the
person at the handset.To end the page at the
base, press PAGE again. To end the page at
the handset, press OFF.
If the Handset is in use ( off hock) when PAGE
is pressed on the Base Unit, the Handset will
emit one page alert. If the Handset is not in
use (on hook), the page alert will continue for
approximately 60 seconds.
This feature is useful in locating a
misplaced Handset.
• Make sure the telephone line cord is plugged firmly
into the base unit and the telephone jack. Make
sure the power cord is plugged in.
• You may be too far from the base unit.
• You may have too many extension phones on your
telephone line to allow all of them to ring. Try
unplugging some of the other phones.
YOUR CALLER FADES IN AND OUT.
You may be nearly out of range.Move closer, or relocate
the base.
YOU HEAR OTHER CALLS WHILE USING YOUR
PHONE.
• Replace the handset in the base cradle, wait a
few moments and try again.
• Disconnect your base unit from the telephone jack,
and plug in a regular telephone. If you still hear
other calls, the problem is probably in your wiring
or local service. Call your local telephone
company.
YOU HEAR NOISE IN THE HANDSET, AND NONE
OF THE KEYS OR BUTTONS WORK.
• Make sure the power cord is plugged in.
• Your base unit and handset may not be operating
on the same channel or security code. Place the
handset in the cradle for a few moments to reload
the security code and reset the channel.
COMMON CURE FOR ELECTRONIC EQUIPMENT
Electronics, like people, can sometimes get confused.
If the unit does not seem to be responding normally,
then try putting the handset in the cradle to re-initialize
the unit. If it still does not seem to respond, perform
the following steps (in the order listed):
1. Disconnect the power to the Base.
2. Disconnect the Handset battery pack.
3. Wait a few minutes.
4. Connect power to the Base.
5. Reconnect the Handset battery.
6. Place the handset in the Base unit cradle. If the
Handset has not been recently charged, allow 8
hours before use.
8 9
10 11

WHAT DOES OURWARRANTY COVER?
• Any defect in material or workmanship.
FOR HOW LONG AFTERTHE ORIGINAL PURCHASE?
• OneYear.
WHAT WILL VTECH DO?
• At our option, repair or replace your unit.
HOW DO I SEND MY UNIT,IN OR OUT OFWARRANTY?
• Call VTECH Electronics customer service for Return Authorization at: 1-800-595-9511
• Properly pack your unit. Include any cables & accessories which were originally provided with
the product.We recommend using the original carton and packing materials.
• Includeinthepackageacopyofthesalesreceiptorotherevidenceofdateoforiginalpurchase
(if the unit was purchased within the last twelve months.)
• Print your name and address, along with a description of the defect, and include this in the
package.
• Include payment for any service or repair not covered by the warranty, as determined by
VTECH Communications.
• In the US, ship the unit via UPS Insured, or equivalent to:
VTECH COMMUNICATIONS INC.
11035 SW 11th Street
Bldg. B Suite 270
Beaverton, OR 97005
VTECH Communications assumes no responsibility for units sent without prior Return Authorization.
WHAT DOES OURWARRANTY NOT COVER?
• Batteries
• Damage from misuse, neglect, or acts of nature (lightning, floods, power surges. etc.)
• Products which may have been modified or incorporated into other products
• Products purchased outside the USA
• Products serviced by the owner or a service facility not expressly authorized by VTECH
Communications
• Products purchased more than 12 months from current date
HOW DOES STATE LAW RELATETOTHISWARRANTY?
• This warranty gives you specific rights.You may also have other rights which vary from state to
state.
IFYOU PURCHASEDYOURTELEPHONE IN CANADA
Pleasecall: 1-800-267-7377 for return authorization.
Ship to: VTECH ELECTRONICS LTD.
200-7671 ALDERBRIDGE WAY
RICHMOND, BCV6X 1Z9
TAKINGCAREOFYOURTELEPHONE .
Your VT 9118 cordless telephone contains
sophisticated electronic parts so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
AvoidWater
Your telephone can be damaged if it gets wet.
Do not use the handset outdoors in the rain,
orhandle it with wet hands. Do not install your
base unit near a sink, bathtub or shower.
Remember that electrical appliances can
cause serious injury if used when you are wet
or standing in water. If your base unit should
fallinto water,
DONOTRETRIEVEIT UNTILYOU
UNPLUGTHE POWERCORD ANDTELEPHONE
LINE CORDS FROMTHEWALL. Then pull the
unit out by the unplugged cords.
Electrical Storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment.
For your own safety, use caution when using
electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing
that should retain its luster for many years.
Cleanit only with asoft cloth slightly dampened
with water or a mild soap. Do not use excess
water or cleaning solvents of any kind.
ThisequipmentcomplieswithFCCANDICREGULATIONS15and68of
the Federal Communications Commission (FCC) rules for the United
States.Italsocomplies with regulations RSS-210andCS-03of Industry
Canada(IC).
A label is located on the underside of the base unit containing either
theFCCregistration number and RingerEquivalenceNumber (REN) or
theIC registration numberandLoad Number.Youmust,upon request,
provide this information to your local telephone company.
Thisequipment is compatible with inductivelycoupled hearing aids.
FCC Part 15
Warning: Changesor modifications tothis unit not expresslyapproved
bythe party responsiblefor compliance could voidthe user's
authority to operate the equipment.
Theequipment has been testedand found to complywith part 15 ofthe
FCCrules. These limits are designedto provide reasonable protection
againstharmfulinterference in a residentialinstallation.This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one
ormore of the following measures:
• Reorient or relocate the receiving antenna.
• Increasethe separationbetween the equipment and receiver.
• Connectthe equipment into an outletor on acircuit differentfrom
that to which the receiver is connected.
• Consultthe dealer oranexperienced radio/TV technicianfor help.
FCC Part 68
The FCC requires that you connect your cordless telephone to the
nationwidetelephonenetworkthrougha modular telephone jack (USOC
RJ11CorRJ11W).
Your telephone company maydiscontinueyourservice if your equipment
causesharm to thetelephone network. Theywill notify youin advance
of disconnection, if possible. During notification, you will be informed
of your right to file a complaint with the FCC.
Ifit is determinedthat your telephoneequipment is malfunctioning, the
FCC requires that it not be used and that it be unplugged from the
modular jack until the problem has been corrected. Repairs to this
telephone equipment can only be made by the manufacturer or its
authorizedagents or by otherswhomay be authorizedbythe FCC. For
repair procedures, follow the instructions outlined under the VTECH
LimitedWarranty.
WARRANTY STATEMENT MAINTENANCE TECHNICAL
SPECIFICATIONS
FREQUENCY CONTROL
Crystal Controlled Dual PLL Synthesizer
TRANSMIT FREQUENCY
Handset: 923.10 MHz to 927.75 MHz
Base: 902.3 MHz to 906.65 MHz
RECEIVE FREQUENCY
Handset: 902.3 MHz to 906.65 MHz
Base: 923.10 MHz to 927.75 MHz
NOMINAL EFFECTIVE RANGE
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
SIZE
Handset: 17.5cm x 5.5cm x 3.9cm
(L x W xT) maximum
(antenna excluded)
Base: 19.3cm x 14.8cm x 5.4cm
(L x W x T) maximum
(antenna excluded)
WEIGHT
Handset: 146 grams
Base: 283 grams
POWER REQUIREMENTS
Handset: Self-contained nickel-
cadmium rechargeable
battery supply, 3.6V nominal,
400mAh capacity.
Power Adapter: 9V DC @ 300mA
SPECIFICATIONS ARETYPICAL AND
MAY CHANGE WITHOUT NOTICE.
FCC AND IC REGULATIONS
The REN is useful in determining the number of devices you may
connectto your telephonelineand still enablethe devices toringwhen
you receive a call. The general rule is that the REN value should not
exceed 5.0 total; however, contact your local telephone company for
the specific number in your area.
IC (Industry Canada)
This telephone is registered for use in Canada.
Notice: The Industry Canada label identifies certified
equipment. This certification means that the equipment
meets certain telecommunications network, protective,
operational and safety requirements. Industry Canada
does not guarantee the equipment will operate to the
user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company.The equipment must also be
installed using an acceptable method of connections. The
customer should be aware that compliance with the above
conditions may not prevent degradation of service in situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas.
Caution: Users should not attempt to make such connections
themselves, but should contact appropriate electric
inspection authority, or electrician, as appropriate.
Notice: The REN assigned to this device denotes the number
of devices you may connect to the telephone loop
which is used by the device to prevent overloading.The
termination on a loop may consist of any combination
of devices subjected only to the requirement that the
sum of the REN does not exceed five(5.0).
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
12 13
14