V-tech JOTBOT 5537 User manual

Instruction
Manual
TM

Included in the Package
*Two of the drawing chips are for saving codes in Code-to-Draw mode.
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part of
this toy and should be discarded for your child’s safety.
NOTE:
Please save this Instruction Manual as it contains important information.
ATTENTION :
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes, cordons et vis d’emballage. Ils ne font pas partie du jouet.
NOTE :
Il est conseillé de sauvegarder ce manuel d'utilisation car il comporte des
informations importantes.
JotBot™ 15 Double-Sided
Drawing Chips*
1 Guidebook
1 Storage Box
1 Washable Felt-Tip Pen

Features
Switch to either or to power JotBot™ ON.
Switch to power JotBot™ OFF.
Press this to confirm, to start an activity or to start drawing.
Command JotBot™ to move forwards (north) in Code-to-Draw mode.
Command JotBot™ to move backwards (south) in Code-to-Draw mode.
Command JotBot™ to move to your left (west) in Code-to-Draw mode.
It can also turn the volume down in other modes.
Command JotBot™ to move to your right (east) in Code-to-Draw mode.
It can also turn the volume up in other modes.
Command to toggle JotBot’s pen position up or down in
Code-to-Draw mode.
Press this to cancel or to exit an activity.
Animated Face
Control Panel
Power /
Mode Switch
Speaker
Drawing Chip Slot
Battery Compartment
Pen
Holder
3

INSTRUCTIONS
BATTERY REMOVAL AND INSTALLATION
1. Make sure the unit is turned Off.
2. Find the battery cover at the bottom of the unit. Use a screwdriver
to loosen the screws and then open the battery cover.
3. Remove old batteries by pulling up on one
end of each battery.
4. Install 4 new AA (AM-3/LR6) batteries
following the diagram inside the battery
box. (For best performance, alkaline
batteries are recommended.
Rechargeable batteries are not
guaranteed to work with this product).
5. Replace the battery cover and tighten the screws to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
ATTENTION :
Les piles ou accumulateurs doivent être installés par un adulte.
Tenir les piles ou accumulateurs hors de portée des enfants.
Switch to either or to power JotBot™ ON.
Switch to power JotBot™ OFF.
Press this to confirm, to start an activity or to start drawing.
Command JotBot™ to move forwards (north) in Code-to-Draw mode.
Command JotBot™ to move backwards (south) in Code-to-Draw mode.
Command JotBot™ to move to your left (west) in Code-to-Draw mode.
It can also turn the volume down in other modes.
Command JotBot™ to move to your right (east) in Code-to-Draw mode.
It can also turn the volume up in other modes.
Command to toggle JotBot’s pen position up or down in
Code-to-Draw mode.
Press this to cancel or to exit an activity.
4

• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES
• Remove rechargeable batteries (if removable) from the toy
before charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat
sources.
3. Remove the batteries if the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
• Only batteries of the same or equivalent type as recommended are to
be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
5

If the problem persists, please call our Consumer Services
Department at 1-800-521-2010 in the U.S., 1-877-352-8697 in
Canada, or by going to our website vtechkids.com and filling out our
Contact Us form located under the Customer Support link. Creating
and developing VTech products is accompanied by a responsibility
that we take very seriously. We make every effort to ensure the
accuracy of the information, which forms the value of our products.
However, errors sometimes can occur. It is important for you to know
that we stand behind our products and encourage you to contact us
with any problems and/or suggestions you might have. A service
representative will be happy to help you.
IMPORTANT NOTE:
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions,
please follow these steps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play with again.
5. If the product still does not work, install a brand new set of batteries.
6

Getting Started
Insert Batteries
(To be done by an adult)
1
• Locate the battery compartment at the bottom of JotBot™.
• Loosen the screws of the battery cover using a screwdriver.
• Insert 4 AA alkaline batteries as indicated inside the
battery compartment.
• Replace the battery cover and tighten the screws.
See page 4 for more information about battery installation.
7

Install Pen
2
• Place a scrap sheet of paper under JotBot™.
• Turn On JotBot™.
• Remove the cap of the bundled pen and insert it into the
pen holder.
• Push the pen gently down until it reaches the paper, and
then release the pen. The pen will lift off the paper
by about 1-2mm.
NOTE: To prevent the pen's ink from drying, please
replace the cap of the pen when it is not in use for a long
period of time.
1-2mm
8

Setup Paper
3
• Prepare an 8x11" or larger sheet of paper.
• Place it on a flat, level surface. Keep the paper at
least 5 inches away from the edge of the surface to
avoid JotBot™ from falling.
• Clear any obstacles on or near the paper. Then, place
JotBot™ in the center of the paper before JotBot™
begins to draw.
NOTE: Tape the 4 corners of the paper to the surface for
the best drawing performance. Put an extra piece of
paper on the surface to protect the surface from staining.
9

4Let’s Go!
Explore more ways to learn and play with the
bundled Guidebook!
10