V8 equipment EBEX.2 User manual

E.BEX.2
EBEX.2
INSTRUCTION MANUAL

2
1. INSTALLING YOUR ROOF TOP TENT
1. a) <RXPXVWKDYHURRIUDFNVFRUUHFWO\ÀWWHGWR\RXU
vehicle before installling the Roof Top Tent
1. b):HUHFRPPHQG\RXSODFHWKH5RRI7RS7HQWLQ
WKHORDGEHDULQJSRVLWLRQ
1. c) $GMXVWWKHWHQWWRWKHURRIVFHQWUHHQVXULQJWKH
UHDUGRRUFDQEHRSHQHGFORVHG
,QVWUXFWLRQVFRQWLQXHGRQQH[WSDJH
SET UP INSTRUCTIONS

USB out: DC5V/1A/2A
Capacity for USB: 13200mAh
DC IN/OUT: DC12V/8A
Capacity for DC: 4400mAh
AC charge: 220V/1.5A, only need 3 hours to get the power pack full charged
Charged by solar panel: 12V/0.4A, need 12 hours to get it full charged
The power pack can be the power source of the motor, as well as be the power source of mobile
phone, computer, outdoor lights. You just need to connect with the USB, then the equipment can
be charged.
Open the tent cover and run the power cord to
your 12V socket.If you want to use the power
pack to drive the tent’s motor, you only need to
push the on-off button. Then connect DC power
line 1 and power line 2, then the tent’s motor can
be charged by the power pack.The power pack
can be charged by the solar panel when the solar
panel is under light. You just need to connect
power line 1 and line 2. No need to push the
button.
Below is some of the parameter for the power pack:

5
Instructions continued on next page.
2. e) Wait a couple of minutes for the tent to set up
automatically
2. f) Hold the ladder, and then pull down

6
2. i) Push the hard top up from bottom gently
2. j)
right side automatically
2. g) The ladder will open slowly
2. h) Pull on the ladder 180 degrees, then it will lock
automatically. Put it on the ground

7
,QVWUXFWLRQVFRQWLQXHGRQQH[WSDJH
3. PACKING DOWN YOUR ROOF TOP TENT
3. a) 3UHVVWKHKDUGWRSIURPXSWRGRZQ
3. b)3XVKWKHODGGHUORFNXS
3. c) 7KHODGGHUZLOOXQORFNDQGLWFDQQRZEH
IROGHGGRZQ1RWLFH3OHDVHGRQRWSXVK
WKHORFNRIWKHODGGHUZKHQVRPHRQHLV
using it)
SET UP INSTRUCTIONS

9
2. h) /RFNWKHEXFNOHRQWKHODGGHU
2. i) /RFNDOOEXFNOHVDURXQGWKHEDVH
SET UP INSTRUCTIONS

4. TIPS & TRICKS
•0DNHVXUHWKHJURRYHLVFOHDQHGEHIRUHXVDJH
•:KHQIROGLQJGRZQDQGFRYHULQJWHQWPDNHVXUHWKHWHQWLVGU\
•,IDOXPLQLXPIUDPHKDVZDWHUMXVWHUHFWLWDQGSRXURXWWKHZDWHU
•.HHSWKHUDLORIPRWRUL]HGSXVKLQJURGFOHDQ
SET UP INSTRUCTIONS
10

E. When the pushing rod is not workable, and you forgot to bring the tools to replace the pushing
rod, you can use below method to hold up and take down your tents.

Step 1: take down the electric arm on the both sides.
Step 2: take out the 2 pcs 92cm poles from the pockets( there is one pocket at the below of tent)
12

Step 3: have one pole hold up the top cover, by doing this, you can save laboring when you hold
up the shelter in the two sides.
13
^ƚĞƉϰŚŽůĚƵƉƚŚĞƚĞŶƚĨƌŽŵŽŶĞƐŝĚĞƚŽĂŶŽƚŚĞƌƐŝĚĞǁŚĞŶLJŽƵŚŽůĚƵƉŽŶĞƐŝĚĞLJŽƵǁŝůůĮŶĚƚŚĞ
back pole ( which used in step 3) will fall down itself, so when you hold up one side, pls make sure
people don’t stand on the back, in case the pole fall down to hurt people.

TROUBLE SHOOTING:
1. Open the plastic part on the side of frame
2. Pull out the white transmission wire carefully
3. Unscrew the waterproof joint
4. Disconnect the waterproof joint
Instructions continued on next page.
14

5. Pull out the transmission wire from the frame
hole right above
6. Pull out the waterproof joint
7. Use big size hexagon wrench to screw off the
nut on the frame
8. Use small size hexagon wrench to screw off the
nut on the tent pole
8. Install the new motorize pushing rod
(assemble step is opposite to disassemble step)
15

SPECIFICATIONS:
Fly: 210D rip-stop polyoxford PU 2000mm with silver coating UPF50+
Inner: 190g polycotton PU 2000mm
Floor:
Frame: Alu. Alloy
Motor: 12VDC, 28W/pc 56W/set
Technology: 2 x Wireless remote control
STRUCTURE:
Person: 2
Inner tent size: 200(L) x 120(W) x 110/85cm(H)
Packing Size: 235 x 38 x 140cm
Net Weight: 62kg
Gross Weight: 77kg
16