Vaisala Beacon Station BWS500 User manual

Setup Guide
M212533EN-B
Vaisala Beacon Station BWS500
Tripod Installation


Vaisala Beacon Station
BWS500
Vaisala Beacon Station BWS500 is a
compact weather station for
environmental monitoring. This product is
intended for outdoor use and can be used
in wet locations.
For the most reliable measurements
choose a site that represents the
conditions that you wish to measure.
Nearby buildings, trees, and heat sources
can distort the measurements.
Check that the installation site is within
the cellular network coverage area of
your network operator.
For powering BWS500, the site must
have sucient amount of sunshine for
solar panel and DC powering.
Follow the recommended installation
order, as well as local and state legislation
and regulations on occupational safety.
Secure the tripod in place to ensure
safety during heavy winds. Clean the
device with a soft cloth and water when
needed.
• Tripod and pole mast DKT504
• Mounting brackets for EGW501, PSU502
and solar panel installed
• Screws, washers, and allen key 5 mm
Tripod and telescopic mast DKT504
The tripod is a portable mast with
adjustable legs. The tripod can easily be
collapsed to fit in a case for
transportation.
• Weather transmitter WXT536
• Mounting kit for Ø 30 mm (1.18 in)
pole mast
• M12 cable to connect WXT and gateway
• Compass for aligning WXT to North
• Allen key 2.5 mm (included with
mounting kit)
Weather transmitter WXT536
WXT536 measures pressure, temperature,
humidity, precipitation, wind speed, and
wind direction.

• Vaisala Beacon Edge Gateway EGW501
Vaisala Beacon Edge Gateway EGW501
EGW501 handles data transfer between
sensors and Vaisala cloud.
Power supply unit PSU502 for DC power
and solar panel
PSU502 when combined with solar panel
converts solar energy into DC power and
stores it in a battery.
• Power supply unit PSU502
• M12 cable to connect PSU and gateway
• Solar panel
More information:
www.vaisala.com/bws500-support
Vaisala Wx Beacon is cloud-based
software for viewing measurement data
from Vaisala sensors.
Wx Beacon collects the data
automatically. Check the observations
from your account in Wx Beacon.
To use Wx Beacon, you need a computer
or mobile device with Internet
connection.
beta.beacon.vaisala.com
Measurements Settings
Air pressure
hPa
16:36
1159.5

Relative humidity
%
16:36
37.8

Air temperature
°C
16:36
21.3

Wind direction
°
16:36
124

Wind speed
m/s
4.3

  
12:32:51 BWS100
Summary Graph
Viewing the observations in
Vaisala Wx Beacon

1
4
2
Orient leg with solar panel
brackets towards midday
sun.
1.1 Open tripod legs.
1.2 Adjust the legs to level
the tripod. Tighten screws
with fingers.
1.3 Check leveling from the
spirit level.
1.4 Attach ground pegs to
keep tripod in place.
Level the station to
ensure right wind
measurements.
4Connect cables and
power up the station
Pull WXT cable
through the mast.
Tie cables to the
tripod with cable
ties.
Connecting power cable to
gateway turns station
automatically on if power is
available from power source.
Set up tripod
1
5Verify connection
to cloud
SNAP!
Install sensors
Weather transmitter
WXT536
2.1 Place mounting kit to
the top of vertical tripod
mast.
Lead the sensor cable
through the mast and
connect the cable to the
sensor.
2.2 Insert the mounting
kit to the sensor and
turn it firmly until you
feel the adapter snap
into the locked position.
2.4 Align the sensor so
that the arrow points to
North.
2.3 Attach telescopic
mast to tripod. Tighten
screw with fingers.
2.6 Open lock and adjust
height of telescopic
mast.
2
Install WXT536
to the top of the
tripod mast.
Keep the upper part
of the protective
cushion on during
the installation.
3.1 Attach edge gateway
and power supply unit to
tripod mount brackets with
16 mm screws.
3.2 Attach 25 mm screws
to solar panel.
3.3 Slide solar panel to
brackets. Tighten screws.
3Install edge gateway,
power unit
and solar panel
EGW501,
PSU502 DC with
solar panel
Install EGW501,
PSU502 and solar
panel to brackets in
tripod.
Orient PSU502 and
solar panel towards
midday sun.
EGW501PSU501
2.5 Tighten the fixing
screw to keep sensor
firmly in place.
Remove the protective
cushion.
Check that the sensor is
aligned to North.
3
NORTH
16 mm 25 mm
Check the observations
from your account in
beta.beacon.vaisala.com
First connection to
cloud may take up
to 15 minutes.
Powering up... (blinking fast)
Power
Connection
Error (steady)
Power OK (steady,
after 60 minutes blinking slowly)
Battery voltage low (blinking fast)
Connecting... (blinking fast)
Connected (steady,
after 60 minutes blinking slowly)
Connection failed (steady)
EGW501
PSU502 DC
13
2
4.1 Connect WXT to
gateway.
4.2 Connect power
source to PSU.
4.3 Connect PSU to
gateway.
Powering
specifications
EGW501:
Operating voltage:
9 - 32 VDC
2 A
PSU502:
Input power:
15 - 32 VDC
Max. 2 A
WXT536
Solar panel
Reserved for future use.
Do not connect.

Safety Note
WARNING! Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
WARNING! If the equipment is used in a manner not specified by Vaisala, the protection
provided by the equipment may be impaired.
WARNING! Assess the risks from the installation work. Take into account also the eects of
local weather conditions. Do not perform installation procedures when there is a risk of
thunderstorm or lightning activity in the area.
WARNING! Do not replace the battery with a battery of an incorrect type. If you do, there is a
risk of explosion. Dispose of used batteries according to statutory regulations.
CAUTION! EGW501 requires a separation distance of at least 20 cm (7.87 in). This distance must
be maintained between the user and the device when the device is operating.
WARNING! alerts you to a serious hazard.
If you do not read and follow instructions
carefully at this point, there is a risk of
injury or even death.
CAUTION! warns you of a potential
hazard. If you do not read and follow
instructions carefully at this point, the
product could be damaged or important
data could be lost.
To prevent electrostatic discharge, avoid touching component contacts or connectors.
When working with equipment in extremely cold temperatures, use appropriate
personal protective equipment such as thermally insulated gloves and clothing.
Wear personal protective equipment (PPE).
Electrostatic Discharge (ESD) can damage electronic circuits. Vaisala products are adequately protected against ESD
for their intended use. However, it is possible to damage the product by delivering electrostatic discharges when
touching, removing, or inserting any objects in the equipment housing.
To avoid delivering high static voltages to the product, touch a conductive part of the equipment chassis with your
other hand before touching ESD-sensitive components.
All rights reserved. Any logos and/or product names are trademarks
of Vaisala or its individual partners. Any reproduction, transfer,
distribution or storage of information contained in this document is
strictly prohibited. All specifications — technical included — are
subject to change without notice.
PUBLISHED BY
Vaisala Oyj
Vanha Nurmijärventie 21
FI-01670 Vantaa, Finland
© Vaisala 2021

M212533EN