Valloy Incorporation Any-001 Anytron User manual

Valloy Incorporation
Any-001
User Manual
Anytron. Digital Color Label Press

1
Ver 1.0.6 (12-Dec-2012)
Table of Contents
1.Certification and Safety...............................................................................................................................................3
1.1. Status of certification ...........................................................................................................................3
1.2. safety instructions .................................................................................................................................3
1.2.1. Installation ........................................................................................................................................................ 3
1.2.2. In use................................................................................................................................................................... 3
1.3. Legal validity of this document .........................................................................................................4
2.Components of the Product......................................................................................................................................5
2.1. Overview ..................................................................................................................................................5
2.2. Component names and descriptions...............................................................................................5
2.2.1. Press station..................................................................................................................................................... 5
2.2.2. Digital printer .................................................................................................................................................. 7
3.Installation of the Product .........................................................................................................................................8
3.1. Requirements for installation .............................................................................................................8
3.1.1. Overview............................................................................................................................................................ 8
3.1.2. Place and environment............................................................................................................................... 8
3.1.3. Installation personnel.................................................................................................................................. 8
3.1.4. Delivery .............................................................................................................................................................. 9
3.2. Installation of the press station.........................................................................................................9
3.2.1. Checking of press station components.............................................................................................. 9
3.2.2. Checking of place, carrying and installation ................................................................................... 9
3.2.3. Checking of Various plug-ins and operations: ............................................................................... 9
3.3. Installation of the printer (digital press) ...................................................................................... 10
4.Installation of the Printer Driver........................................................................................................................... 12
4.1. Installation of the driver ................................................................................................................... 12
4.2. Configuration of the roll (continuous paper) driver ................................................................. 16
4.3. Description of the printing mode.................................................................................................. 19
4.4. Multiple of printing according to image length........................................................................ 20
4.5. Inquiry and download....................................................................................................................... 20
5.Installation of the Software .................................................................................................................................... 21
6.Mounting and Operation of the Roll (Continuous Paper)........................................................................... 21
6.1. Specification of the roll (continuous paper) and cautions...................................................... 21
6.2. How to mount basic (215mm) paper ........................................................................................... 21

2
6.3. How to mount 6 inch and 4 inch Paper ...................................................................................... 24
6.4. Overall operating process ................................................................................................................ 27
6.5. Checking alignment of mounted media ...................................................................................... 29
7.Printing Operation ..................................................................................................................................................... 31
7.1. How to use the basics of illustrator for any-001....................................................................... 31
7.2. How to use pre-cut media............................................................................................................... 33
7.2.1. Adjustment of the sensor’s location and how to auto-sensing ..........................................33
7.2.2. How to change the sensor.....................................................................................................................35
7.2.3. Setup of the printer driver..............................................................................................................................35
7.2.4. How to use the SLongTool.....................................................................................................................36
8.Post-printing Process (cutting and laminating) .............................................................................................. 38
8.1. Digitalization of process after printing......................................................................................... 38
9.Maintenance and Management............................................................................................................................. 39
9.1. Overview ............................................................................................................................................... 39
9.2. Types of errors on the printer (press) LCD messages and its description.......................... 39
9.3. Checking thereplacement cycle of consumables and replacing ........................................... 39
9.3.1. Checking of the replacement cycle of consumables.................................................................39
9.3.2. Replacing consumable items.................................................................................................................40
9.3.2.1. Toner cartridge replacement............................................................................................................40
9.3.2.2. Image drum replacement..................................................................................................................44
9.3.2.3. Replacing the transfer belt unit......................................................................................................47
9.3.2.4. Fuser replacement.................................................................................................................................49
9.3.2.5. Clean the LED heads............................................................................................................................50
9.4. Purchasing of consumables............................................................................................................. 51
9.5. Inquiry and download....................................................................................................................... 51
10. Product Specifications........................................................................................................................................... 52
11. Service Guide and Product Warranty.............................................................................................................. 54
11.1. Warranty................................................................................................................................................ 54
11.2. Service and inquiry ............................................................................................................................ 54

3
1. Certification and Safety
1.1.Status of certification
Registration Number
: KCC-REM-BTI-ANY-001
1.2.Safety instructions
- Because safety instructions are necessary to prevent accidents or dangers, please make sure to follow
them to ensure that you use this product safely.
1.2.1. Installation
- Install the product in a stable place without danger of falling.
- Do not install the product in a place with high temperature or moisture. The product may not
operate properly under these conditions and there might be a danger of electric shocks.
- Do not use loose sockets or defective power cords, as there will be a danger of electric shocks and
fire.
- Plug the power cord into a socket and a multi-consent with an earth terminal.
1.2.2. In use
- Do not carry out inspections or repairs except if you are a qualified persons.
- Do not disassemble arbitrarily or subject the machine to impact or dropping.
- Do not use around magnetic materials or store near them.
- Use the product in a place without electromagnetic interferences.
- Do not put things, which are heavy or have a risk of spillover, on the product.
- Do not use chemicals or detergents etc. for cleaning the product.
- Use only programs provided by or approved by Bitek.
- When printing, you may get burned due to high temperature. Except at the time you fill the rewinder
with the paper at the early stage of the printing, please DO NOT TOUCH the parts of rewinder.
Especially, please pay special attention as the temperature of shaft 2 and rewinder tension bar between
the printer and rewinder is very high.

4
1.3.Legal validity of this document
-We inform you that this manual does not carry legal binding force, and we reserve the right
to change this manual at will without giving a separate notice.

5
2. Components of the Product
2.1.Overview
2.2.Component names and descriptions
2.2.1. Press station
No.
Name
Description
1
Press Station
Mechanical part to control the process of hanging, feeding roll
paper and winding it back after printing.
1-1
Unwinder
Part to mount roll paper. The unwinder releases as much
paper as is needed to feed the printer, which allows the paper
to keep its tension constant.
1-2
Unwinder Tension Bar
Sensor bar for feeding paper. When paper is fed up to the
printer, the tension bar would be moved up by the tension. At
this time, the sensor works to rotate the unwinder and release
the roll to maintain the paper’s tension.
1-3
Shaft No.1
Shaft (axis) for feeding paper
1-4
Sensor
Sensor to support labels precut
1-5
Feeding Roller
Roller to insert paper into the printer when printing.
Holds remaining paper after printing and feeding it.
1

6
1-6
Cutter
Cuts continuous paper when finishing ordered printing.
1-7
Feeding Guide
Guide for paper moving from the feeding roller to the printer.
Role of aligning paper horizontally evenly during printing.
1-8
Button Panel
Front panel with 2 LEDs and 4 buttons
1. POWER LED
LED to check on/off conditions of the station
2. MARK LED
LED to check whether the sensor detects marks in the sensing
mode
3. Cut Button
Button for operating the cutter 6
4. Rew Button
Button for operating the rewinder 11
5. Feed(<) Button
Button for operating the feeding roller 5 (moving paper
backward)
6. Feed(>) Button
Button for operating the feeding roller 5 (moving paper
forward)
1-9
Shaft No.2
Shaft (axis) for feeding paper printed
1-10
Rewinder Tension bar
Sensor bar for rewinding. When paper connected to rotation
of the rewinder is wound up, the tension bar moves up by the
tension, at this time the rewinder’s rotating speed is reduced
to allow the paper to keep constant tension.
1-11
Rewinder
Part to rewind printed paper.
1-12
Rewinder guide
Guide to uniformly wind paper on the rewinder
1-13
Power Button
On/off button for the station

7
2.2.2. Digital printer
No
Name
Description
2
Digital Printer
Printing device
2-1
Top Cover Release
Button
The top cover is opened by pressing the button.
2-2
Top Cover
The cover is opened by pressing the button 1.
2-3
Operator Panel
Menu-based control and LCD panel
2-4
Multi-purpose Tray
Tray for using continuous media
2-5
Front Cover Release
Lever
The front cover is opened by pulling the lever.
2-6
PowerSwitch
(On/Off Switch)
Printer power switch
2-7
AC Power Socket
Connection for printer power cable.
2-8
Rear stacker
Tray that accepts and stacks printed continuous media as it
is released.
2-9
USB interface
Interface that directly connects a PC with the printer
2-10
Network Interface
Interface to use the printer via a network
2-11
ACC interface
2-12
Parallel interface
2

8
3. Installation of the Product
3.1.Requirements for installation
3.1.1. Overview
-This product is a printing device and digital electronic communication equipment. Accordingly, this
product can implement optimum printing quality only if it is installed in a place meeting
environmental requirements for digital equipment as well as the conditions required for a label printer.
For this reason, our company makes it a rule to professionally install our products by our staff or our
designated agency’s personnel and we request that customers follow our personnel’s suggestion for
the locations of the equipment along with the environmental requisites for optimal operation.
3.1.2. Place and environment
-The operating environment of this product is as follows, and it should be installed in a place
satisfying the specified conditions for temperature/humidity. In addition, considering the gross weight
of this product, it should be installed on a level rack that can withstand a weight more than 3 times
that of the equipment, at least. Additionally, cleanliness of the working area and minimization of dust
is essential for high-quality printing in particular.
Item
Condition
Value
Environment
Temperature
17 - 27˚C
Humidity
40 –60% RH
Loading
rack
Horizontal orientation
Minimum size
Minimum supporting weight
250 Kg
Antistatic ground
Others
3.1.3. Installation personnel
- Our company makes it a rule to visit in person to ensure a professional installation by our staff or
our designated agency’s personnel. Please contact by [phone] or [email] if you have any questions
about the product installation service performed by our personnel or any of our agents.
Manufacturer :BITEK TECHNOLOGY INC,
E-mail :[email protected], Tel : [phone]

9
3.1.4. Delivery
-The installation personnel will completely install this product and software (such as the printer driver)
and also a test printa roll of continuous paper. At this time, the delivery will be completed by the
customer’s signature on the receipt.
3.2.Installation of the press station
3.2.1. Checking of press station components
- The press station is mounted or projected by a unwinder, rewinder, tension bar, sensor and cutter etc.,
and is a smart station that is intricatelyconnected with various semiconductor circuits and wires to
electronically control these all components, rather than being a simple rack to put a printer on.
Therefore, the same care is required as with the printer (digital press) when moving or installing it, so
please follow understand the installation personnel’s instructions and this manual.
3.2.2. Checking of place, carrying and installation
-carefully carry the press station to the place of installation selected previously in section 3.1.2 before
the printer (digital press). This press station has a gross weight of 150Kg, with an overall size of (length)
71cm ×(width) 193cm ×(height) 70cm, which should be carried by at least 4 people. Because there
is an electronic circuit board at the rear of the press station, it is recommended that the rear is put as
close as possible to the wall for stable installation.
3.2.3. Checking of Variousplug-insandoperations