Valor Legend 739ILN Manual
Legend
4001839-11
©2010, Miles Industries Ltd.
Manufactured by
British Columbia, Canada
www.valorreplaces.com
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING
!
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING
!
For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical
appliance that must be installed by a qualied dealer. Each Valor replace is fully
tested during the production process for your safety and comfort.
Your unit has been professionally installed by:
Dealer Name _______________________________________
Phone Number ______________________________________
.
The information contained in this installation manual is believed to be correct at
the time of printing. Miles Industries Ltd. reserves the right to change or modify any
information or specications without notice. Miles Industries Ltd. grants no warranty,
implied or stated, for the installation or maintenance of your heater, and assumes no
responsibility for any consequential damage(s).
Do not put
furniture or other objects
in this space in front of
the replace:
36” (0.9 m)
Fireplace
Hearth
2
= Updated content
◊
◊
◊
◊
◊
◊
◊
Table of Content
3
Safety and Warning Information
Children and adults should be to the hazards
of high surface temperature and should to
avoid burns or clothing ignition.
should be
when they are in the same room as
the appliance. Toddlers, young children and others
may be susceptible to
. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access
to a replace or stove,
to keep toddlers, young children and
other at risk individuals out of the room and away from
hot surfaces.
place furniture or any other combustible
household objects within 36” of the replace front.
and all instructions carefully
before starting the installation.
these installation instructions may result in possible re
hazard and will void the warranty.
Prior to the rst ring of the replace, the
Owner’s Information section of this manual.
this appliance if any part has been under
water. Immediately, a qualied service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
Installation and repair should be by a
qualied service person. The appliance and venting
system should be before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is that
the unit’s control compartment, burner, and circulating
air passageways to provide for
adequate combustion and ventilation air.
Always the appliance clear and free from
combustible materials, gasoline, and other ammable
vapors and liquids.
the ow of combustion and
ventilation air. Keep the front of the appliance
of all obstacles and materials for servicing and proper
operation.
Due to the high temperature, the appliance should be
out of trafc areas and away from furniture
and draperies. Clothing or ammable material
on or near the appliance.
This unit MUST be used with a vent system as
described in this installation manual. vent
system or components .
This gas replace and vent assembly be vented
directly to the outside and be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance a separate
vent system. Common vent systems are .
the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air ow.
The glass door assembly be in place and sealed
before the unit can be placed into safe operation.
this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualied
service person. strike or slam the glass door.
The glass door assembly be replaced
as a complete unit, as supplied by the replace
manufacturer. material may be used.
abrasive cleaners on the glass door
assembly. to clean the glass door
when it is hot.
the gas before servicing this appliance.
It is recommended that a qualied service technician
perform an appliance check-up at the beginning of each
heating season.
Any safety screen or guard removed for servicing
before operating this appliance.
not to put any decorating objects
sensitive to heat to close above or around the replace
as it gets very hot when operating.
use this heater as a temporary source of heat
during construction.
This appliance is a
. It must not be used for any other purposes
such as drying clothes, etc.
Fuels
used in gas, wood-burning or oil red appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
4
Safety and Warning Information
Natural Propane
0-4,500 feet*
26,000 24,000
6,500 13,000
3.6 10.0
5.0 11.0
10.0 14.0
82-750 92-260
35 27
Min. Rate By-Pass Screw 125 125
Specications
This appliance is certied to ANSI Z21.88-2009 / CSA
2.33-2009 American National Standard / CSA Standard
for Vented Gas Fireplace Heaters for use in Canada
and USA, and to CGA 2.17-91 High Altitude Standard
in Canada. This appliance is for direct vent insert
installations.
This appliance complies with CSA P4.1-09 Testing
method for measuring annual replace efciencies.
The installation must conform to local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 or the Natural Gas and Propane
Installation Code CAN/CGA-B149. Only qualied
licensed or trained personnel should install this
appliance.
This appliance must be electrically grounded in
accordance with local codes, or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA
70 or the Canadian Electrical Code, CSA C22.1.
Input ratings are shown in BTU per hour and are
certied without deration for elevations up to 4,500 feet
(1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
Heating value of gas in some areas is reduced to
compensate for elevation—consult your local gas utility
to conrm.
For installations at elevations above 4,500 feet
(1,370 m) in Canada, please consult provincial and/or
local authorities having jurisdiction.
Heater engine 739ILN is used with natural gas.
Heater engine 739ILP is used with propane gas.
The supply pressure must be between the limits shown
in the Ratings section above.
The supply connection is 3/8” NPT female and located
on the left hand side of the control valve. The gas line
entry point is on the left hand side on the replace.
The 739IL Legend G3 is supplied as natural gas or
propane gas and is eld convertible between fuels. See
instructions packaged with the conversion kit for further
information.
The 739 does not require an electrical power source to
operate as a heater. However, if the appliance is tted
with a fan, a grounded power source is required.
When operating your new replace for the rst time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the ames to be the full height of the rebox, or
even slightly higher, for the rst few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the ames will be at their normal height.
5
Overview
6
28-5/8” (727 mm)
19-1/2” (495 mm)
12” (305 mm)
or 12-5/8” (321 mm)
Varies with
outer trim options
9-3/8” (238 mm)
or 10” (254 mm)
Varies with
outer trim options
20”
(508 mm)
Gas inlet Gas connection Electrical inlet
Optional Outer Trim or
Surround sold separately
X
Y
Dimensions
Cavity
Check that masonry step does not interfere with install dimensions or
vent pipe.
If mantel is combustible, see section Clearances for allowable
clearances.
Minimum width of replace opening at front: 28” (711 mm)
X = 12” (305 mm) or 12-5/8” (321 mm)—varies with outer trim options
Y = 20” (508 mm)
7
9” (229 mm)
A
B
Do not put
furniture or
objects within
36” (914 mm)
of the front of
appliance
*Measure taken from the underside of the mantel to nished hearth
or surface that the unit is sitting on.
Material such as wood,
compressed paper, plant bers, plastics or any material
capable of igniting and burning, whether ame-proofed or
not, plastered or un-plastered.
Material such as steel, iron
brick, tile, concrete or materials that bear the UL mark for
zero (0) re rating.
distance from side of appliance (liner box) to
combustible wall: 9” (229 mm).
1”
(25 mm)
4”
(101 mm)
8”
(203 mm)
14”
(355 mm)
28”
(711 mm)
32”
(813 mm)
35”
(889 mm)
38”
(965 mm)
8
Clearances
3” Liners
3” min.
Bend
Radius
Terminal Cap
Flashing
2 x 3” ex
liners—see
Venting Table
for length
allowed
See list of approved Venting Accessories on page 28 of this manual.
The vent terminal must be located through the
roof. This direct vent appliance is designed to
opreate when an undistrubed airow hits the
outside vent terminal from any direction.
Check local codes for allowable vertical vent
termination.
Maximum vertical height 40 ft (measured to bottom of termination)
Minimum vertical height 10 ft (measured to bottom of termination)
Maximum horizontal run 4 ft (measured center to center of pipe)
Maximum offset angle 45˚ (sweeping bend to allow for obstructions)
Where possible, avoid joining ex pipes. If joints
are required, use a approved connector and seal
joints with RTV high temp sealant.
Horizontal offset is permissible to allow for
routing around masonry projections. Avoid
bending ex pipe over a 45 degrees radius
where possible.
9
Venting
Installation Planning
2. Unpack the appliance.
3. Check that you have everything.
4. Clean cavity, chimney, ash dump, and clean-out.
5. Install venting pipes.
6. Attach conversion plate to existing replace.
7. Install and test blower if used.
8. Fit appliance into cavity.
9. Connect and test gas supply.
10. Install bricks and logs.
11. Ret window.
12. Put batteries in receiver and remote control
handset.
13. Set-up remote control.
14. Connect electrical wiring blower if used.
15. Verify operation and adjust aeration settings.
16. Install the remote control handset wall holder.
18. Install the surround trim and front.
19. Install the fret if required.
• Packing knife
• Screwdriver set
• Pliers
• Adjustable Wrench
• Sealant
• Dish soap/water solution
• Gloves
• Eye Protection
• Electric outlet if installing a blower
Existing Fireplace Preparation
A few points must be considered before inserting the
739IL into an existing replace cavity. Generally, no
modications are allowed to the existing replace that
will compromise the integrity of the existing replace.
Components that are bolted or screwed on such as
dampers or bafes may be removed to accommodate
the installation of the 739IL engine.
. Check with local authorities if in doubt.
Have the chimney swept and the replace cavity
including ash dumps and clean-outs cleaned before
installing the 739IL heater and vent liners. Any creosote
or soot residue remaining in the replace cavity
chimney or clean-out may cause odors or stains once
the 739IL insert is installed. Consult with chimney
sweep for information on how best to clean.
Factory-built, zero-clearance replaces will require the
damper to be removed in order to install the vent liners.
These dampers are usually bolted into place. Dampers
in masonry replaces must be xed open and may
remain in place.
Some replaces (particularly factory-built) have a
raised curb at the front edge to retain ashes. Check the
dimensions carefully to ensure the 739IL engine will t
behind any raised curb (some curbs may be removed
separately from the refractory base).
10
1. Unpack the appliance.
2. Unpack any loose items from around the appliance
and check against the Pack Content list provided in
the documentation package.
3. Remove the window and set aside in a safe place to
avoid damage—see next page.
including:
-brick panels & logs;
- surround/doors/fret;
- venting components and accessories;
- blower and electrical components for blower
installation if used.
Appliance Preparation
Existing Fireplace Preparation
Plan the routing of the gas line before proceeding.
Utilize the existing hole for the gas line of the factory-
built replace. If the replace has no access hole,
carefully drill an access hole of 1.5 inch (38 mm) or
less through the lower sides or bottom of the rebox.
The access hole must be plugged with non-combustible
insulation after the gas supply line has been installed.
See Dimensions section for detailed location of gas
inlet. Also, take into consideration whether or not a fan
or shut-off valve will interfere when planning routing of
the gas line.
prior to installing the 739IL insert.
Combustible mantel clearances must conform to those
required for the original solid-fuel replace into which
the 739IL is being installed.
Attach the “This replace has been converted...”
label to the existing replace using screws or other
mechanical means and store any removed parts in
back of the existing replace for future use.
11
Appliance Preparation
The window is held in place by four spring-loaded bolts,
two at the top and two at the bottom.
1. To remove the window, turn each bolt a quarter turn
to disengage the bolt pin.
2. Gently pull the bottom of the window outward and
unhook it from the rebox’s opening frame.
3. Set the window aside in a safe place to avoid
damage.
electrical
outlet
fan
cavity
If the 755CFK Circulating Fan Kit (blower) is to be
installed, we suggest that you do it now.
The fan cavity is accessible from the back of the rebox
to facilitate its installation. If the fan is retrotted after
the installation of the appliance, the burner module
will need to be removed. Therefore, we recommend
that, where possible, the fan be installed before the
appliance is tted into the cavity.
Refer to instructions provided with the 755CFK to
install the fan.
12
IMPORTANT: This appliance’s venting system is room sealed and
therefore, does not require room air to be used in the combustion process.
1. Rough-in two 3” diameter vent liners into the existing chimney
system from the roof. Be careful not to tear or damage the liners in
the process. It may be easier to install both liners at the same time
rather than one at a time. Leave plenty of liners at the bottom to
facilitate the connection of the liners to the vent slider.
Slide the appliance into the cavity.
Release the two screws retaining the vent slider to the front of the
rebox.
Remove the slider from the rebox by sliding it towards the back of
the rebox.
3. Apply RTV sealant to the collars on the vent slider and t the
two liners exhaust
. Secure with 4 tapping screws
per liner.
If the vent slider was removed from the rebox, slide the rebox
onto the vent slider in the cavity taking care not to damage the
liners.
Secure the vent slider to the front of the
rebox with two screws removed earlier.
4. From the roof, pull
the liners and t the
ashing.
5. Fit the terminal
cap
. Secure with
8 screws provided.
6. Seal the terminal
and ashing from
water penetration
as required.
Appliance Preparation
Failure to position the parts in
accordance with these diagrams or
failure to use only parts specically
approved with this appliance
may result in property damage or
personal injury.
13
Supply
pressure
test tapping
Manifold
pressure
test tapping
Gas Supply Installation
The gas supply inlet connection is a 3/8” NPT female
connector and is located on the left hand side of the
control valve.
Use only new black iron or steel pipes or copper tubing
if acceptable—check local codes. Note that in USA,
copper tubing must be internally tinned for protection
against sulfur compounds.
The burner platform and gas train on this appliance
may be removed as a unit for servicing or to install or
remove the optional circulating fan (if installed). Provide
some form of pipe union (depending on type of piping)
as close as possible to appliance valve.
Unions in gas lines should be of ground joint type.
The gas supply line must be sized and installed to
provide a supply of gas sufcient to meet the maximum
demand of the appliance without undue loss of
pressure.
Sealant used must be resistant to the action of all
gas constituents including LP gas. Sealant should be
applied lightly to male threads to ensure excess sealant
does not enter gas lines.
Pressure test the supply line for leaks.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
The appliance must be isolated from the gas supply
piping system by closing its equipment shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psi
(3.5 kPa).
Failure to either disconnect or isolate the appliance
during pressure testing may resulting regulator or valve
damages and void the warranty. Consult your dealer in
case of damages.
The minimum supply pressure is given in the section
Specications of this manual—page 5.
All piping and connections must be tested for leaks
after installation or servicing. All leaks must be
corrected immediately.
When testing for leaks:
• Make sure that the appliance is turned off.
• Open the manual shut-off valve.
• Test for leaks by applying a liquid detergent or soap
solution to all joints. Bubbles forming indicate a gas
leak.
The pressure test tapping locations is shown in the
gure below. An internal regulator within the valve
controls the burner manifold pressure. The correct
pressure range is shown in the table in subsection
Ratings of this manual on page 5. The pressure
check should be made with the burner alight and at its
highest setting. See Lighting Instructions section for full
operating details on page 26.
Pressure Testing
14
Ceramic Bricks Installation
The following guidelines apply for all brick liners.
1. Inside the rebox, on the top of each side, release
the screw of the side brick anchors (one per side)
just enough to allow them to rotate.
2. Place the rear panel against the back of the rebox,
on the ledge at bottom.
3. Rotate the anchor up and out of the way and slide
the left hand side panel against the rebox side.
Rotate the anchor back down to hold the panel.
Ceramic Logs Installation
Unpack the ceramic logs very carefully to avoid damaging the fragile material. Install the logs as shown below.
1. Spread the decorative charcoals on each side of
the log tray, covering the sheet metal as shown.
4. Rotate the anchor up and out of the way and slide
the right hand side panel against the rebox side.
Rotate the anchor back down to hold the panel.
5. Tighten the side brick anchors on each side of the
rebox.
6. Install the port cover xing it using the two screws
already in the rebox top.
15
Both front logs to rest slightly on the
edge of the rebox window frame.
5. Identify the right cross log; it has
a hole under on of its end and it is
the shortest cross log. Place it on
the right pin located on the rear
log. Rest its other end in the crook
of the front right log.
6. Identify the middle cross log. It does not have a
hole underneath. Place its narrow end on the at
depression in the rear log next to the right cross log
on the rear log. Place its wider end on the front log.
7. Identify the left cross log; it has a hole under its
narrow end. Place its narrow end on the pin located
on the rear log. Rest its wider
end on the the crook in the
front left log at an angle of
approximately 30 degrees
from the center line of the
replace to allow for the
ame to come up in front of
the rear log.
2. Place the rear log centering it side to side in the
rebox. Position forward until it sits against the
sheet metal return behind the burner.
3. Place the front left log on top of the burner with its
front edge resting slightly on the window frame.
4. Place the front right log on the top of the burner
with its left end abutted to the front left log and its
front edge resting slightly on the window frame.
Ceramic Logs Installation
16
Bottom
of window
(wider frame)
Window Retting
1. To ret the window, hook its top part to the rebox’s
opening frame.
2. While you hold it, push in and turn the two top
spring-loaded bolts a quarter turn to engage their
pin.
3. Push in the bottom of the window against the rebox
and fasten the two bottom spring-loaded bolts a
quarter turn.
4. Then, pull out the top and bottom of the window and
release it to insure the springs return it.
5. Apply light hand pressure against the window frame
sides to bed-in the window seal.
Remote Control Initial Set-up
The receiver and the handset of the remote control sys-
tem must be initially synchronized before the rst use.
1. Insert alkaline batteries in the remote control
receiver and handset. The receiver is located left of
the control valve under the burner module.
2. With a sharp object, press and hold the receiver’s
reset button until you hear one short and one long
beeps. Release the reset button after the second
beep.
3. Within the subsequent 20 seconds, press the small
ame button ( ) on the remote handset until you
hear two short beeps conrming the sychronization
is set.
This is a one time setting only and is not required when
changing the batteries in the remote receiver. The
remote control system is now ready to use.
17
Packing Contents:
1 Wall Bracket A
2 Screws B
1 Screw C
2 Wall Anchor D
1 Spacer E
(detach before assembly)
1 Wall Bracket F
Switch Plate
Alternative 1
Alternative 2 Alternative 3
Remote Control Handset Wall Holder Installation
The remote control kit for this replace
comes complete with a wall-mounted holder.
This holder is not required in all installations
but is provided as an optional feature for
those customers who wish to mount the
remote handset to the wall.
To install the holder to the wall, nd a
convenient location and use the hardware
provided with the kit. See the diagram below
for required hardware and congurations.
Note that the holder can be installed at the
base of a light switch plate.
. The location of the remote
control handset is important to assure proper
temperature regulation. To obtain a constant
temperature, we recommend that the handset should be between 3 and 15 feet away from the appliance
. We also advise that the handset should be located away from any other heat source and not in
direct sunlight as this may affect the temperature sensor located in the remote handset.
Operation Check & Aeration Settings Adjustment
Turn the replace ame up and down using the
remote control to conrm that the full range of inputs
is achieved—see the remote control operation
instructions on pages 22–25.
Light the re and allow the unit to warm up for 10–15
minutes to evaluate the ame picture. Burners are
equipped with an adjustable shutter to control primary
aeration. See the gures below. The shutters are
factory-set to an aeration gap which will give optimum
performance for the vast majority of installations.
In a few unusual installations, the ame picture may
be improved by adjusting the aeration. The need for
adjustment should be determined only by operating the
appliance with the ceramic logs and window installed.
will cause the ames
to appear more transparent and blue showing more
ceramic log glow.
will cause the ames to
appear more yellow or orange showing less ceramic
log glow.
Too little aeration may result in black carbon
forming and dropping into the rebox.
Open
Open
Close
Close
Flashback
shield (for
LPG only)
LPG Air Shutter
Slider Open
Close
NG Air Shutter
Slider & Cover
18
Bottom
of window
(wider frame)
For your safety, this appliance is tted with a ame
supervision device which will shut-off the gas supply
if, for any reason, the pilot ame goes out. This device
incorporates a xed probe, which senses the heat
from the pilot ame. If the probe is cool, the device will
prevent any gas ow unless manually lighting the pilot.
See full lighting instructions on page 26 of this manual.
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white lm on the ceramic glass of the viewing door.
The composition of the deposit varies widely from
various locations and also from time to time in the
same location. It seems this is associated with the
varying sulfur content of the gas. You may have the
problem for a time and then not see it for many months
when it will reappear in your area.
We have discussed this problem with ceramic glass
manufacturers and they cannot give us a denitive
answer to this problem. Dealers have tried various
cleaning products with varying results. The following
recommendations will not guarantee results in your
particular case.
Owner’s Information
Performance of LPG appliances may be affected by
the quality of commercial gas supplied in your area.
• Clean the glass regularly as soon as you notice
the buildup (white lm). If the lm is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive to
ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
»»Brasso,»Polish»Plus»by»KelKem,»CooK»ToP»Clean»
Creme»by»elCo,»WhiTe»off»by»ruTland,»TurTle»Wax
Do not clean the glass while it is hot. Always
securely replace the window before lighting.
To remove the window for
cleaning:
1. To remove the window,
turn each bolt a quarter
turn to disengage the
bolt pin.
2. Gently pull the bottom
of the window outward
and unhook it from the
rebox’s opening frame.
3. Set the window aside
in a safe place to avoid
damage.
To ret the window:
1. To ret the window, hook
its top part to the rebox’s
opening frame.
2. While you hold it, push
in and turn the two top spring-loaded bolts a quarter
turn to engage their pin.
3. Push in the bottom of the window against the rebox
and fasten the two bottom spring-loaded bolts a
quarter turn.
4. Then, pull out the top and bottom of the window and
release it to insure the springs return it.
5. Apply light hand pressure against the window frame
sides to bed-in the window seal.
Warranty
Card at the
back of this
manual.
Let the replace cool rst before cleaning it.
Your replace becomes very hot when operating.
Avoid placing decorating objects sensitive to heat
within 36 inches (0.9 m) around it.
Do not put
furniture or other objects
in this space in front of
the replace:
36” (0.9 m)
Fireplace
Hearth
19
Soot or dust can be brushed from the ceramic logs
and rebox walls using a soft brush. Dust can also
be removed from the burner using a soft brush after
removing the ceramic logs. When cleaning, make sure
that no particles are brushed into the slots of the burner.
A periodic check of the pilot and burner ames should
be made. Check after the re has been on for at least
30 minutes. The pilot ame must cover the tip of the
thermocouple probe. The main burner ame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions.
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
ammable vapors and liquids.
Inspect the vent terminal outdoors regularly to make
sure that snow, trees, bushes, leaves, or other objects
do not obstruct it.
Examine the vent system and terminal regularly. We
recommend annually.
Pilot Flame can be
seen between logs
Owner’s Information
Pilot
Flame
see instructions
next page.
The appliance uses four 1.5 V AA alkaline batteries
for its remote control receiver and one 9 V alkaline
battery for its handset. Batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should the
batteries loose power, the control may be operated by
manually turning the control knob at the valve or by
turning off the valve at the switch.
:
1. The receiver is located to the left of the valve and it
is retained to the rebox by a Velcro tab. Grab the
receiver and pull it out from its location.
2. Slide and remove the receiver cover.
3. Replace the 4 AA batteries.
4. Replace the cover.
5. Put the receiver back in its position pushing it in so it
attaches to the Velcro tab.
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be helpful
if the appliance’s serial number can also be quoted. This
number is on the rating plate, which is located under the
burner. The replacement parts are shown at the end of
this manual. Please always quote the part number and
description when requesting spare parts.
a screwdriver or other metallic object
to remove the batteries from the receiver or the
handset! This could cause a short circuit to the
receiver.
20
Other manuals for Legend 739ILN
1
This manual suits for next models
1
Table of contents
Other Valor Indoor Fireplace manuals
Valor
Valor 1700JN Operating instructions
Valor
Valor 495 User manual
Valor
Valor BR Assembly instructions
Valor
Valor Ultimate Assembly instructions
Valor
Valor 739-72ILN Operating instructions
Valor
Valor 650JN Operating instructions
Valor
Valor 1600IN Operating instructions
Valor
Valor CHURCHILL 32-810-58 Assembly instructions
Valor
Valor Legend 736CN User manual
Valor
Valor ULTIMATE TURBOCHIM 517SF Assembly instructions
Valor
Valor LINEAR SERIES User manual
Valor
Valor Visage 640 Assembly instructions
Valor
Valor COSYFLAME TURBOCHIM 528 Assembly instructions
Valor
Valor Horizon 601SFB User manual
Valor
Valor LX2 2200LKN User manual
Valor
Valor LX2 CORNER User manual
Valor
Valor 1700KN Planning guide
Valor
Valor 1500IN Operating instructions
Valor
Valor L1 1600KN User manual
Valor
Valor HORIZON 534JN User manual
Popular Indoor Fireplace manuals by other brands
Morsø
Morsø S80-90 Instructions for installation and use
RAIS
RAIS Q-Tee 2 Instructions for installation, use and maintenance
Superior
Superior CFPF-CMN installation instructions
Montigo
Montigo 36DV-SH Installing and operating
Marquis
Marquis MQRB4436N Infinite Series installation instructions
Continental Fireplaces
Continental Fireplaces CB36NT Installation and operating instructions
Vermont Castings
Vermont Castings VFF32LI Installation & operating instructions
The Collection By Michael Miller
The Collection By Michael Miller Aleesia DDAL RN Series Installation, maintenance & user instructions
Majestic
Majestic 36MCUFD SERIES Installation and operating instructions
furniture123
furniture123 AGL049 user manual
Dragon Wholesaling
Dragon Wholesaling 564 HO GSR2 (AU) owner's manual
Quadra-Fire
Quadra-Fire QV32B-A owner's manual
pleasant hearth
pleasant hearth GLF-5002-75 installation instructions
Vogelzang International
Vogelzang International Colonial TR004 owner's manual
Woodbridge
Woodbridge DV32CV Installation and operating instructions
Dimplex
Dimplex DF3033ST user manual
decoflame
decoflame DENVER F6 user manual
Acucraft
Acucraft Blaze BL-6-ST Installation & operator's manual