Valor Legend 937AN Instruction Manual

Legend
MODEL 937AN MODEL 937AP
FOR USE WITH NATURAL GAS
FOR USE WITH PROPANE
GAS FIRED VENTED ROOM HEATERS
)r
WARNING: If the information in this
manual is not followed esactly, a fire or
explosioil result causing property
damage, personal injury or loss of life
- Do not stme ox use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
-
WHAT TO DO 11; YOU SMELL GAS
Open windows
- Eixthguish any open flame
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phbne in your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas s~rpplier's
instructions.
If yo11 cannot reach your gas supplier, call
the fire department.
- Installation and service must be periorn~ed by a
qualified installer, service agenq or the gas
supplier.
This appliance is a7
domestic room l~eating
appliance. It must not he
used for any other
purpose such as drying
clothes etc.
L
Vous pounez vous procurer un cxemplaire en langue Frallgaise de cette btochure chrz wtre
conccssionail-e

OPTIONS ....................................................................................................................................................................................................,.................
GENEKLU, DATA ...........................................................................................................................................................................................................
LOCATION IN THE P.OOL,l .......................................................................................................................................................................................
SUPPLY GAS .................... .. ............................................................................................................................................................................................
PACK CONTENTS ..................................................................................................................................................................................................
APPLL4NC:E PREPARATION .......................................................................................................................................................................................
.........................................................................
.............................................................................................................
(;AS SIJPPT..V TNSTAI..J.;\TTON :
........................................................................................................................................................
BASE & MAIN APPLIANCE INS'TALL-ITION
kT.E.N'I' CONNECffON ........................................................................................s........................................-.................................................................
GAS LfNE CONNECTION .............................................................................................................................................................................................
SYSTEM CHECK ......................... .. ............ ...................................................................................................................................................... .........
CERAIMIC FCIEL BED ASS,&VBLY ...........................................................................................................................................................................
CONTROLS OPERATION CKECK ......................... .. .............................................................................................................................................
AEPA-I'ION AL?fUSTMEhT .........-......... . .................................................................................................................................................................
FACW INSTALLATION ..... .. .......................................................................................................................................................................................
VENTING CHECK , ................................................................................................................................ ...................................................................
Fii\JAI. Ch-ECfi ..-............ ... .................................................................................................................................................................................. ..
..
................... ..........
................
..........................
OPERATING TFIE f,lEATEH .... .. ...,,,
...............................
LIGHTI~GWITH A LONG IMATCH ............. , ............. ..,. ............................................................................................................
CLEANING ......................................................................................... .. ..............................................-................-...................................................... .

Due to high temperahres, the appliance should be
located out of traffk and away from furniture and
draperies.
-
Childrenand adults should be alerted to the hazards
of high surf'ace temperatures and should stay away to
avoid bums or clothing iflition.
Young children should be carefully supervised when
thcy are in the same room as the appliance.
Clothing or other flammable material should not be
placed on or near the appi' lance.
The glass and front fratne must be put back in pIace
prior to operatitlg the appliance if they have been
removed for servicing or cleaning,
Never operate with broken or damaged windo\v glass.
This appIiance should be installed and repaired by a
qualified service person.
The appliance shodd be inspected before use and at
least annually by a professional senice person. More
frequent cleaning may be required due to excessive
lint fiom carpeting, bedding materid, etc. It is
F imperative that control compartments, burners and
circulating air passageways of the appliance are kept
clean-
Keep curtains, clothin&, furniture and other
flammable materials at least 3Gins (90cm) fiorn all
parts of the appliance
Keep the appliance area ~rcll clear and free from
combustible materials, gasoline and other flammable
vapors and li-ids.
If any changes arc made to the rooxn constructinr~ it
the vicinity of the appliance after instaIIation (P:
additional mantle etc.) make sure that the chan!:~
conform to the installation requirements in d?i
manual.
Never attempt to burn paper or any other material ::
the appliance.
Keep the base of the appliance clear to prex-CT;
obstruction of air flow to the appliance. If fitted. 1;L;t:'
a pedestalbase, make sure that the grill at back is nc.
obstructed. If fitted with legs, make sure there is T~.
obstruction between the legs.
This appliance must be properly connected to
venting system. It is equipped with a vent safct-
shutoff sysrem. Operating when not co~ec~d to
proper17 imtalled nfid rnaintcthlcd venting system r:
tampering with the shutoff system can res~~lr ii
carbon monoxide (CO) poisoning and possible dear!!
The venting system should be checked peridicn?:?
Recent trends itl home improvemerrt and newr ti~l~t F.
construction txhniques have contribi~ted
problems with venting. E you suspect that F~Y'
appliance is not venting properly, do not opera:/
Seek eqert advice.
Do not use this appliance if- any part has beeit utlJc
water. finmediately call a qualified service technicin:
to inspect the appliax~ceand to replace any part v
the control system and any gas control which F.:,
been under water.
NOTE
mrr? operating your nmr stovc for tllc first time, some vapors may bc released which may cause a $ti& &or and could possibly SC~ ~ff 3ny in?!.
dctcnion alms in the immediztcte iicinity. Thee vapos arc quite normal on ncm appliance. Thcy are to:ally harmless and uill disappear xfter a ::-
houo use.

Xi10 CFK Circulatitlgfan Lc (For bare only) is a-:aiIablc:
as an option for this appliancc. C>pcnud by a t-ariable spccd
controller, it is designed to boost. rlic natural convrction pnxess
throa~h the heate:. 1t may be fitted bcforc the heater is imtalied
or retrofitted at a later datc. Full installation and opcradng
instructions arc included xvkh the kit
This appliancc is ccrti5~d by Jatcrr)ationd Appmval Services fur
usc in Canada and the USA
The instzllation nlust conform with 1oc;ri coda or, in the absence
of local cocles, with thc current CAN/CGA-Bl49. i~~s:allat?on
code in Cailx& clr the current National FucI Gas Coclc, ANSI
ZZZ3.1 in the LYSh Only qwlificd liccnscd or trained permnnel
should insdlthc appliancc.
This applhce is only fix w wth thc tgx of .p indicxttcd on
the ratins phtc.
2.1 Rating plate
The rating piate is lmccd inside thc control
cotnparunenrdoor.
2.3 Pressures (in. w.c.)
t
I Natural. gas I Propane
I Supply- / Manifold - 1 Supply - I .Manifold -
thermostat
I 1 fir11 on) I 1 full on)
Mau 1 10.5 1 3.5 9.5
2.4 Orifice data
Forveriicationonly. Do not atwmpr ro drill or othc.~.~isr law!(:<:
the appliance input.
--
I
Na turd Gaq 1 Propnnc
-
I Type / No of I Dia. 1 Type 1 No of ,f Ii3 '
Pilot I 40 I 1 1 0.022 1 1-1 1 I 1 C~.Ol~ :
Fhmt 1 18- 1 1 / 0.04:
I
7 1 0.027 1 105 1
2.3 Venting
This appliance is for connectiotl to an approved 9" mctai
vcslt.
Rear
Cotnbustible materials insidc the room most not be closer th-il
thc dimensions shown in fiatire 1.
Tl~r flwr cousuuc~iou sl~uuid allucv tllc hcatcr tn 'bc scrcv..cd t:~
tllc flmr. If the heater is to be insnlled directly on a?;.
combustible m~terialother than ud tlmrin.5 it rnrlxr I-c
insrallcct on a meul or wwk! panel extending the full width an,?
depth of the appliance.
Modcl'337hI\i is for [rnc only\&i:h n:ltural gs. Mock1 9YN1 is
for use only with propme gas. The suppl!; prcssux must k
bcnvccn thr. limits shown in section 23 of tfrh mulual.
The supplv corlrlectjon is 3i,"~~-f. Opel~hgs for rhc p5 supply
are provided ior rmor i~ndcrfloor connection (see figure 1:).
:<4
1.8-
350
.
7
O.tJ27
103 1
--.
O.$!L :
I I

,
Combuslible ceiling or overhang
3 r
s toGs pipe
undeilioor mnneetion
WITH PEDESTAL
Combustible &:inp or overhang
* > -- --x
I i
,?',/' ./' , + ,
,' ,' / ,./,',' ,.',
,':' ,/
/
15 3:d"
/ conibustible wa!l controls access
WITH LEGS
T rnir
7 114- !O gas
Pl=-n~~
... t
4' min. to
s mr-. for
wmbus:iSle wall coctrclb %ess
Fig. 1 nimensions & cleamces
1

'The completc appliance j~ contained in rwu pcb. Onc of the
altcmativc base rupprt and front designs will hc includcd -
either pcdrstal with conccrnporw faci~ or Lcg vd<tIltraditional
C~cin (Scc pack2).
Pack 1 - Main appliance unit contains:-
1 Main appliaqcc iitced with wirtdow.
3 Ccnmic Ic~.
2 Crmndc firi~ck h: bars.
1
Pair ccramic kbox side wal!s.
1 Ceramic fircbx back wall..
1
D~or.~tiiic vcnt cellar kir a!>pliancc top.
1 Gx$ supply inlet pipc.
1 Gas supply inlet clhcnvhcnv
Pack 2 - Pedestal and conbsmporar). facia sltcrnatke
ciuluins:-
1 Ycdcaal unit.
1
Contemporary design front faciz unit.
1 ~'bh!ip unit
4
#.S mpping screws ('for hing ashlip).
4
Machinc screws (for fixing pcdestai to rnxin appliance).
2
\Xfcmd scrm (for floor &kg).
2 Piugs (for floor .fixing):).
or
Pack 2 - Legs and traditional facia alternative r.onuins:-
1 Hsse ?i Icp unit.
1 Traditionaldesign front facia u111t.
'I mmr retaining brackcr.
1 'iV~ndow franc top cover.
2
el I) tapphg screws (for door rewiniug bracket).
1
Machine scrm~ (fbr fudng b;ae rsi lcg unit to main
3ppliancc).
2
Wood screws (for flow fing).
2 I'lugs (far floor fr6ng.
T~ke carc when removing thc contents from the pach$n.g to
prcvcnr dama~. Check that all the con:ents are iz the packs and
arc unctlrr.gcd.
6.1
Reniove the winrIt>\v & logs (see fiewe 2)
6.1.1
Detach the window unit by removing the nvo hurlv::
scrrv.5 ("Ar) 2nd huried nut ("B*) holding thc sides 2nd
bottom uithe \rindc.wframc.
6.1.2 Lift the windo\v unit up and fowards ro unhonl: th:: ti.?.
Put thr. window in a mfe p1ac.c.
6.1.3 Takc the ccramic !ogs and ceramic front ban our of :%c
firebox and storc safely.
6.2
Check ignition electrode spark (see fi-gurc- -2)
Illcpilot burner and elrr;trdc arc at the ri&t side 9Frhrr
fircba
(3ptil thc control mess dwr. Turn the ps contr:jl h~t,
(the ri&t hand hob) counterclock\vke to " 1p". 'X3: 11;
turning pilot ignition spwh shvuld bc activated twice
Chcck tiut thc sph arc produd at tt~c pilot L.r;r~cr.
If no spub arc produced. check that the wiring is sccurr
and that thc spark gap is 3.5 L0.3 mm.
Route tllc p.s supply line w the applian?:. inlc:
mnrlection point (scc figvrr I).
Xex: Pmslc: rtdn'tr,: tire line fir iwks trraj. ~ied 10 bc. jle!&r,l:r,.'
B@iorc I& litre 5 wnttecvd in the applinrrm - xcercctk?~: iii.
Gas connection to the appliance is 3S"NYT.
Usc only tlcw bhck iron or stel pipes or COFpCr c{ll>ing I:
accclpt~ble - chcck local coder. i\?ot~ drol i)i L;Y:4 cop:-).!
rubing mr~st. hc intenrally hn~rcd >r lvuttction ppirsl s~r&!.
c0n;poumis. ,
Unions in gas lines should be of gonndjoinr ?ype.
The ps supply liz~c: nzusr be sircd and installed tc) pt0x.i 3:
a supply of sut-ficicnt to mcct the maximum dcmgi?:!
of tht ;~~pliancc without undue lo= of pressure.
Scalan.ts used must be mistant to thc action c\f 211 k,:~ :
cc-~~stltucntsincluding LP ,gas. Sedatlts should k ?p~ii?:i
liehtly to mnak threads to cnsutc ckxcs* sealant tlors 11i-
cntcr gz lincs.
The supply lint should includc a manual sbt~r-c.~<-,~~~::::
allow the appliance to k dismnnecrcd for sen.ir:inp.
A pl~h.cd W"NYT upping tnust Ix insiallcd in the lirl:.
nnncccirn
The mppi~g must trc accessible for test gauge c-
and br inmlcdiz:elv clpstrcam of he p5 SU~;\'IC
cor~ilection to the arlslinnce.
[Fi?;. 3 Pilot i,pition sysrcm,
. -.

8.1 PEDESTAL BASE
8.1.1
Detrch thc pdestal front panel by removing two screur.
8.1.2
Place the pcdcseai in position (scc fi-rc 4). 'The htotn
rcar 0:' thc prclcstal must bc at lest 2!hw fn~ra thc back
u-all to maintain thc 2'hrelr cicannce shoun in fi.qrc 1.
5.13 1M;ttk :hs floor viirh the floor firing positions throu@ thc
holes in thc pedestal (see ftgr;rc 4).
5.1.4 Remove the pcdtstd. Drill the flwr at the marknl
positions and fit plug ifn~~c;ar);.
8.1.5 For easier fii:y, fir the nvo ~wxlscrcm suppIicd into
thc floor p~nixlly 1ca';ing a spacc bc:t.veeu thc wrew ha&
end the floor. Thc pedestal has tan 'keyhole" openings
in its bottom cl~anne!~. Phcc the pcdcsotl back in position
by dropping it to loutc thc xrcu-s in the wide hola of
the kcyholes and thru sliding thc pcdcstal bck to locatc
thc screws in the uamu- slots of the kcyholrs. Tighten
the scrcnvs.
8.1.6
Fit thc inlct elbow to the rupplv pip.
hrore: Ifthc optitmu1 circulating jhn kit is intmdcd to be instalhi,
it nn'll k twiest lOJt it at thia rtaxc
8.1.7
Phcc the twain applkncc unit over the pedestal, :1Iig11 tilc
4 f~ng hots (2 u each side) and srcure rhc unit to thc
pedesul nith 4 machine scrcw.
8.2 BA.SEE?Tv LEGS
S.2.1
Dc~~ch chc dwr rrtGning bracket (loc~trttl ned: rhr rr.ll
right comer of the a~pliance main unit) by rc~i?i;ng P.. :.
scrcw ((sct figlrr 3).
8.2.2. Swing the hotrorn of rhc door fonwrd to rc1e;ts.r r!;c
lnxtorn pin from rhr slot in the CA:C and lift tllc door
clear {set: fipc 3).
KEXlOt'E BR4Ck'ET
i
!
I
I! I ! i
i; i
I
I
i! j
I
,
1
,
I
I L
I
1
I
I
i
i
i
i
I
SWKG DOOR FORVL4R.D
Fig. 3 Soor rcmovd 1
-
8.2.3 P1;lce tllc base in pition (scc
6). ).'i'!:c rcar of :lir
be must hr at Seas: 2" 3~x2)- h>rn ilic JC:I~ iv~lI t~! al!i..;:.
air fiav to the iilsuile J applia ace.

8.2.4
iulnrk rhc floUr f;xing positiot~s through the !?olcs in !hc
rmr fccr.
8.2.5
Rsrnove the base. Drill thc floce 3t thc rnarkcd witions
and fir plug if nacssary.
1.2.6
Rttpia*3e? thc base. Fit wo&cre\~ through tt5c rexr feet
i~nd tightcn.
8.2.7 Fir tllc inlct elbow to the supply pipe.
8.2.8 Phcc the main appliance unit m-cr the basc, align thc
securing holes (see figure 6). Sccurc with 4 machinc
screU;5.
8.2.9 Kcplacr: the door as fi>llour;s:
8.2.9.1
htc the hir* pin at top of the d~r intc the holc at
the wp of chc door avrnxre (scc figure 7).
8.2.9.2
Kacarc the hingc pin at Lmttorn of tkc door ir.:c :!ti :i.:.,.
in the ba~e. Swing the httorr! of the door part ~-2y :<-
the lnck A new door xtaininq brilckct ir; suppiird -.t;!:li
thc leg 3nd 9cia kit. Hold this bracket uncicr
k~nom of the bsc side. Position it with tile t.>io hcic:
at chc bott0111 and locatc thc single h~le wcr ?hi..
bottom door hillgc pi.. (see figure 7).
8.2.9.3 T7hilc keeping the I~raclxt Iwsred to the hingc Fir'.
svingthe dmr and bnckcr fill!). backmards. Ai,p :hc
nvo holcs in the bnckcrivith thc two holes in the I>a:c
side and fixwith thc tsw tapping screws provided (scc
fi-~rr? 7).
LOCATE TOP DOOR HiNGE Pl N
LOCATE BOTTOM HINGE PIN IN SLOT & SWING
DOOR PART WAY TO BACK
I FIT BP,SChTT TO HINGE PLV & SWh'G sACK SECURE RRACKlEl" R7Il-I 2 SCR13XfS 1
I
Fig. 7 Door fitting with 19 design base

Conncct 2n approwd 4" vent unit to the applj5anre vent collar.
A dcuor~tiv: vent colhr is suppliedwith the applimcc ta cover
the vent and applisnce.co.olliujoint at the top of thc hater.
'10.1
Opcn thc sonu01 pancl door.
10.2
Pull off rhc nvn cvntrol knobs.
10.3 Dctach the mntroI cwa panel {scc figure 8):-
Remow thrcc screws.
Lift the panel up
Pull thc buttom front comet of the pancl hard and
outtoclmr the casc and then lift clear.
10.4
Couple thc ps inlet pipe to thc connector below the
reg~~lator (scc 9).
11.1
Pressu~ wst the supply Iit~e for 1cak~.
The q:plinncc and its i~~ddividunl sl~ut-ot'i'v,~l~-e rr!:~::i
k disconncctcd horn thc PS supply piping sycc. rri
during any pmsure tesrin~ of that syztcrn :I[ :c:r
pmr.lires in esccss of '/iysig (3.5kPa).
Tlic appliance must be isolated fron the 91; pi>!:.
piping system by c!osing is individual rnanu:tl shui-
offvab.:e during any pressure testing of the 9: suppi-;
piping system at test pr~ssuresequd to or le;; ti?:,:.
'hpsig (3.5kPa).
*
Failure to cithet disconnect or isdate the appliani:!
during prcssurc eating may rcsult id regwlator o;
valve damag. Consult your dcalcr in this ewe.
11.2 Thc appliance is p.mct tn ~ive the corrcn inpur wrrh
natud F. For input adjusrmenq tlic supply prcr::tr
to the appliancc inlet must within the tang shc~vn ii:
section 2 of this manual.
11.3 Thc burner manifold prcssure is coarrclllcd by ;l built-il:
nnn-~dj~stahlrregulator. The correct prcssard: mng 1..
sham in thc tthle in section 2 of this rnan~i~i. 7'5..
manifold ptessurc should be checked at the pressurc st
point mhjch is lruated on the thcrmosut unic (;rc il.ri.lr-.
9). Thc: prrsprc check should be made with .i..
appliance burning, the p+s control scr. at '-On" and si!..
thermostat control set at 'Full". (Temporarily rctit
contrni bobs for check in^.)
11.4
-Ali piping and connccrion:: must be ccstcd for !elks at;$-.
in~ttill~ti~n or scnicing. .UI Icak milst bc rsrrcr:c.!
immediatclp.
Whcn testing for icaks:
Make sure that the appliancc g;ls control knob i.; :I-
the "OF position
Opcn the mmual shut-off valve.
Test for lcah by spplying a licl~~id Jctcrg,cnt or sc,.l?
solction to all joints. Bubbles forming indic~tc ;I e:...
leak Nwer rue as gcctj70m.e lo cluck fir &ah.
Coma ;my leak detectcd i.m.rnrdizttely.
Fig. 9 Inlet pipe conncction Si ressurc test poitlt
105
Connca the other cnd of the inlct pipe tu the elbctw
attached to :he supply line.

12.1
Plxc the cenn~ic hxck wall in position centrally at the
backof the Crcbnx. It tr~usl rcst on thc mctd ledge at tile
bnckof the fircbr~x (see figup 10).
Fig, 10 R:ck wall position
122
Place thc ccramic sidc zv;lll~ in position at the sids of the
firchox The sides arc left md right handed. Thc sidcs
should locate in thr slopingchannels !leer thc bottom of
the fircbos sides and in thc alp btwccn each sidr of thc
5rrboxand thc black :op hftle (see fiprt: 11).
1.2.3
Plaa the re;u lop (the log without a bnnch) in rhc
rminitl~cradlc behir~d i11c rcar humcr tubc with its back =pinst
:hc hack \-all. Centcr the log so that the gap to tlic side wall is rhc
samc at rwh sidc (KC 6-spe 12).
12.4
Plnco the front log on thc retainitig cradles ktwrcn rt:-
rear and front bun~er. rubes. Centc: rhc log so that ti!: g::
co dlc side wall is chc same at wch side. Scc rhr b< ;o rh-t.
thcre i:; A sFacc of apvrozcimateb,r 14" k&~-cen the hxck.
fi1c.e of the rear br~nch and surCacc or'the rear ICS <:cl-
figurc 13.
I Fig. 13 Front log position
I
125 Place the cross log in position. The front cf :his ID? 1,:
indic~teci by rhe 1-r -F" cn~'~sscd underneath. Makc
sure that tbc fint of thc mss log is s~~trd insidc tht:
Irollc~u in the front log and is not raiscd in front of it (;a:.?
fig.1~ 1 4).
-.
rig. 1.1 Cross log
I
j
I'
.

12.6
Place the tv~o cervnic ban: over thc fx>r~t mi! of the
fircbm (see figr~rc1 .i).
Fie. 13 Ceramic hars mxition
13.1
KeGt the conrrolcover pmcl. Kcfit r.hc mr, c?c,ouc>l hlobs
13.2
if instalicd wit.11 a pcdcstal brse, refit tlic pcdcstil iron:
p:l!lel-
13.3 If iustdlcd with mditional dcsign fiont frcia, fit tllc
\v-i11dtm- hmc top wtrr (supplied in rhe pack) ovcr thc
top of the wit~do\v hmc to hide tllc barc meal (see
G.pre IG).
Fig. 16 Tt'mJc~fi top cover
13.4 Rcfie the window (with top cover if zpplicable).
Hook thc top of thc \Yindo,u. fraamc over the Greh
top front edge.
Swing ~hr wivi!ldo\v d~~s'~1 over the hrtorn ,:tx\rc
locating stud.
Sccorc the \vindow unit in pbce by r*;fittiny ti-<
hurled nut and nvo knurled screvs ac rhc silJcs >:lri
bottom orthe window fr~me.
Check ignition, gas conrrnl v;~lve and thcrrn.?st.,[
settings as described in thc lighting insrnictio:!,:
section fttrthcr on in this 11lanux1.
These appliances arc quip@ with uljustable shuacn i<l cc\rrcrqi;
primary :wation.
Natural ps appliances have shi.utters on borh hnr and rcar
burncr tubes.
Propane $;at applihnces Invc a shutter on the rcar burncr tr~ke
Thc fmnt tuk 1ras an opcn air hole without a shurtcr.
The 3ir holes arc at thc right side of the tubcs - Scc fig 17. 'f 1:::
shuttcn can slide to the right to rcducc the air slipply ot. to tilc I-!':
to incrcasc it
The X~~~~IKC is supplied with the shr-~ttcm sct tn suit the .:ar:r
majority cf instalht;~~~. No adj~~smcnt stiould U~LIRIJ~ %L
necessary, Hmrrr, in emin insm1btion.s (c.g Low Btu mlr.~c
gas, high dtimckt) it may bc ncccssary to adjust t1c s1ru:r.cr position
of vnr or b.h ofthc blirncrs to obtain the optimal -;isaa! r<&ct.
17 Acratio~ shutter.;

.mop (surd ~VJJIICO aqlm13 9.~1
-aopwdo
;i! pui: ~AIFAJJO lnys L~ddil~ aqa 3~ UO!1ZJO1 3ql ano ~LI!O,-J
~LI
'ld ,:
3=21 ?r p>>!.U3S '~BSS~XU
;! 'Fue p3333dq s! ams!lddl: alp 1q1 pu~~rn~~ ~LT
-aaou!lddr, 31p S'uyerxto xopq qaln33 pm~ldx q
lsnu mopu!~ aqi aaqr ssaq apq~nls!pj! do1 aqi lass 10
21?1::u! ay~ urqs 01 p]co pueyo lnqs s! a~uexidd~ aqiu39~
!mc.our-l aq .<cur mopursr, xp 'hassamu 31 '1q1 as!qV
~LT
-r;>uz!ldd.c 293 a~nacfo 01 ~~oq J~LLYLC> atp wnnnrI
~LI
-no!~u~ado lElSOUJ3tp pUl: (OJVrCO S& 733v33?4
t*Ll

For full lighting instructions see next page-
nn oprrolirc ins~rtrrtions arc nko itt.ti.de ti= control pdttel door.
18.1
For your safety this appliance is fitted with a flme
supervision device which uill shut off the pds supplv if,
for any texwn, the pilot flames go out. This dnicc
incorporates a fwd pmbe which senses the hcat fr~m the
pilot flame. If the probe is cool, tllc dcvicc xvi1I prrwrt
any gas flow utr.less the ps control knob is kp pushed in
bmvaen the "OW and "Tpn positions. See full li&tiug
instructions onnext page.
18.2
Oped the mntrol pancl dmr at right side of the heater for
access to thc controls. Clox the door wllcn you have
finisl~edoptration the controls.
18.3 The Valor Cmnfoshi" Tcmrerature control system
Convcntional thcmosms regulate rhc rcrnpcratun by
shuttingthe burners offwhen the tcmpciatt1:c reaches its
upper litnit. This gives stop-go heat, unnaturally varying
flama and impaired eficicncy {ih 3 c;u in city mffrc).
The Co~nfimt~ system controls the cemperaturc by
grad~dly lnweri* or raking thc firc. This maintains
ruom comfort by pro~dingsteadier heat and a morc
nxtural lwkinp regulation of tilt flflarncs. Thc nmnl
tempraturc will bc mintrined at the desired lcocl f~r
any scning up to just short of the mFull"position. The
"Full" position is an -errride which \\72l kccp thc firc
full:; on ail the time and is not a.Rccted by mom
trnrperature.
18.4 Wheu fhst tui~icd oa, thc decomtivc tlarncs will apFa.r
predominantly bluc. Afcrr .~p~~rnxitmtely 15 minuccs the
flarnm \\ill turn yellow.
18.5
Aftrr appdmtely th~ houn usc at the high crntml
setting the he1 picccs\\ill shew itru.s of chrwillgray color
as mold rul burning I*.
Ir. the utzlihly event of fiilurc to cwtt an ig~lilirionspark using
the control knob, thc stow can be lit zi ftbllo~vs:
19.1
Lift off thc front fxia
19.2 Remove th windmvunit
19.3
Open thc conrrol panel door.
19.4 Itlserta long burning match zt tile pi!ot.
19.5 (.>prr.uc? the conr.rols as dcscribcd in the lighting
instructiom.
19.6
1Mab sure that the pilot flame is stabletc.
19.7
Replacethe wi~ldarv uuit sccurcly.
19.8 Rcplacc the facia.
13.9 Select the burncr sctting.
19.10 Closc the control panel door.
20.1
Only clean when the appliance is cold.
20.2
NormalIy-, thc appliance should only need dusting hy
srains on thc ccnmic glass windsm rau Lk: tcmoecd with
a n~n-abrasive clnr~sr. Nmp1 uc ulmii.r clcnncrs art tlte
glass,
20.3
Dun. ctc. can bc brushed from the logs ah dettching
thc front 6%~ mci \\indo\\"- If you arc rcmoving the log,
we sugest that they :ire remavcd in the rrrersc nrdcr v:
thnr shown in the fuel bcd assembly instructions. i?t?-'.
ttc. can aim k removed from the burnen using a ~ott
brush &cr removing thc log. \:(/hen cleaning chr bur11c1.r
alw check thc acrrtjon holes (we fig.1'7) 2nd hrusll clcdli I:
necessary. Makr sure that no pmiclcs arc brr~shhd il~to :I!:.
burner tubes.
20.4 fivs).s replace the ceramic bars. wjndcni- 2nd f~cil af::>r
an); cl~aning as shown in rhe iristallationsccrion of these
in~ructinns.
205
Coloring of the metal fircbos is normal whcn used. 0::
not tv toremove the colorwit11abrasicc m~tcrixls.
21.1
A periodic visual check of the pilot and burncr flamc:
should be madc (scr figures 22 tk 23).
- - - -
!
i
j
j
t
!
f
CORRECT i
!
i
;
i
WRONG
I
j
Fig 22. Burncr flanks
1
i
!
I
I
!
I
1
I
I
I
Fig. 23 Pilot flama i
21.2
Thc appliance area must alw*ys be kept clear and frcr
from cornbx~stiMc materials, psolinc and 0th-I-
flammhlc vxprs md liquids.
21.3 Kccp thc b~x r>f the appliance clcar to prcvc:n!
ohstmction of air flow to the appliance. Lf fittcd v;irh J
pedestal base.. makc surc that the grill at back is r?,-i
t~hstrucctd. If fi~d with le~, makc s~~rc thrrr is n.:.
obstruction hem-een the leg.
21.4 The venting rwrn sbo\~ld hc eedmined rephhrly t.; ;.
qualified qcn.7. We suggest an annual checi-
! i

'VirAlXNlNG: Ifvoudonot follow these instructio~lsexactly, a fire or e~;plosivn ma). result causing proper?- 1
damage, pcrsona~injury or loss of life. -. . . 1
A.
This appliance has a pilot which must be lighted by hand. %'hen lighting the pilot, follow these
instructions exactly-.
B.
BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smeIl next to the floor
because some gas is heavier thm air and will settle on the floor.
WH.A.T' TO DO IF YOU SIXELL GAS
Do not try to light any appliance,
Do not touch any clcctric switch; do not use any phone in >.our builtling
Immediately call ymr gas supplier from a aeighbor's phonc. FolIow the gas supplier's instnrctions.
If you cannot reach your gas supplier,call the fse department
C.
Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not ~ush in
or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair m:cy
result in a fucor cxplosioa
I?.
Do not use this appliance if any part has been under water, ~dediately call a qualified service
technician to inspcct thc appliance and to replace any part of the control system and any gar control
~7hich has bccn undcr water.
1. STOP! Read the safety information ab-c on this page.
b i
I
The;n:ma~ L?& Q% control imb
i
2. Set the thermostat to its lowest setting.
3.
Turn the gas coa~ullalobclockwise 17 to "Oft".
-
Note; Knob cannot be turned to Wff" unless it is pushed in partially.Do not force.
4.
Wait five (5) minutes to clear out any gas. If ~u then smell any gas. STOP! Follow "D" in the safety
information above on this label. If you don't slllell gas, go tonext step.,
3.
Find the pilot It is attheright side of the firebox.
6.
Push in and turn &c gas control knob counter- cloch-ise n untiI resistance is felt. Keep pushed in at
this position for a few seconds to allowgas to flow.
7.
Kccp hob pushcd in and turn to "Igti" to lightpilot mileturning to this position ignition sparks will
be activated twice. Hold knob in for a further 5 seconds then release.The knob should pop hack up. The
pilot should remain lit. Xfpilot goerc outrepeat steps 3 through 7. If pilot does not light at all during a
few- attempts, tty lightingxvith a long match as described on previous page.
If pilot lislitc but will not staylit after several tries, h~rn thc gas control knob t.ouO.ff" and call your
sen-icetechnician or gas supplier.
8.
When pilot is lit, partially depress the wax control knob and turn countcrclockwisc
to "On*.
Do not leave knob set between "I& and "Onz.
9. Set thermostat to desired setting.
10. Close~vntrolaccess door.
,Mways replace the window unit after match lightin the pilot.
servicetechnician or gassupplier.
ti
The gas conttol khob should always pop up when re ssed Xf it does not, stop and immediately call your
1. Set the thermostat to lowest setting
2.
Push in the gas control knob and turn clockwi.e 0 to Donot
force.
3. Close control access door.

If you require any anention to y7)ur appliance, contact your
supplicr quacin~ thc model numkr. It will br hclpfi~l if tb:
appliance scri+i nom.ber can also bc quoted. This is on thc ratitig
plate visible w!m the control pancl door is apencd.
Thc repair paru: arc shown in the. eapwnte rcpir pam leaflet.
Plwe alw~ys wsqrlote part number and description when
requesting spare pan.
- C
Distn'buW in Central and
Eastern USA by
VALOR HEATING
Post mice Box 773
Franklin. Ky 42135
Ph (Toll free)
Sales 800-892431 35
Service 800-654-8534
Fax [phone]
.
Distributed in
Eastern Canada by
VALTECH INDUSTRIES
6660 Kennedy Road
Missis=uga
Ontario L5f 2M9
Ph. (905) 7956333
Fax [phone]% .
J