Valor tuscany 637 User manual

600B128/04
Tuscany
Model 637
(GC No. 32 032 06)
OWNER GUIDE
This Owner Guide is intended to hel
p
y
ou care
f
or
y
our Valor
g
as
f
ire.
Please read carefully before using your gas fire and keep for future reference.
This Owner Guide gives sufficient details to enable your gas fire to be operated and
maintained.
IMPORTANT.
Please keep your Owner Guide in a safe place together with the
Installer Guide.

2
Thank you for choosing Valor.
All Valor gas fires are designed to meet the most stringent quality, performance and safety requirements to provide our
customers with many years’ trouble-free service.
Your owner guide aims to improve your understanding and appreciation of your Valor gas fire by providing simple and
informative instructions to ensure that youbenefit from the excellent performance and features it hasto offer.
If you require further assistance or any advice about gas in general, the Valor AdviceLine will be pleased to help.
Please telephone [phone] (local call rates apply in the United Kingdom).
FOR OTHER USEFUL TELEPHONE NUMBERS SEE INSIDE BACK COVER.
Model 637 is for use with natural gas (G20)
This appliance is for use in the United Kingdom (GB) and the
Republic of Ireland (IE) only.
CUSTOMER CARE

3
SAFETY
IF YOU SMELL GAS
DON’T SMOKE
EXTINGUISH ALL NAKED FLAMES
DON’T TURN ELECTRICAL SWITCHES ON OR OFF
TURN OFF THE GAS SUPPLY AT THE METER
OPEN DOORS AND WINDOWS TO GET RID OF THE GAS
IMMEDIATELY CALL THE GAS EMERGENCY SERVICE- SEE YOUR LOCAL TELEPHONE DIRECTORY
1. As with any gas appliance, this fire must be
installed by a competent person. In the United
Kingdom, installation must be in accordance with
the latest edition of the Gas Safety (installation &
use) Regulations.
In the Republicof Ireland, installation must be in
accordance with all national and local regulations
in forec.
2. If the fire is intended to be installed to a chimney
which was previously used for solid fuel, please
note that the chimney must be swept prior to
installation.
3. On no account must the fire stand on carpets or
other combustible materials. The fire must stand
behind a non-combustible hearth surface. The
hearth material must be at least 12.5mm thick. Its
top surface should be 50mm above floor level to
discourage placing carpets. Rugs or other
combustible materials over the hearth. The
minimum sizeof the hearth is shown in figure 1.
4. The minimum height from the top surface of the
fireplace to the underside of any shelf made from
wood or other combustible material and which is
not more than 150mm deep is 200mm.
For shelves deeper than 150mm add 12.5mm to the
above clearance for every 25mm of additional
shelf depth.
5. Never put any paper or other material on the fire.
Never add any extra coals above the number
stated in these instructions. This could cause a
safety hazard.
6. It should be appreciated that although this
appliance conforms to all the applicable
standards, it is a decorative fuel effect heating
appliance and certain parts of its surface will
become hot. A suitable guard which complies with
BS 6539 or 6778 should be used for the protection
of young children, the elderly and the infirm. Such
a guard is also recommended for the protection of
pet animals.
7. Always switch the fire off and allow to cool before
handling. Note that this appliance retains heat for
some time after it has been switched off.
8. Never hang clothing, towels or any other fabrics
over the fire.
9. This appliance is fitted with a device which will
automatically shut off the supply of gas to the fire
if, for any reason, the flames go out. If this device
does operate or if the fire is turned off accidentally
or intentionally, always wait three minutes before
attempting to relight.
10. Soft wall coverings (e.g. embossed vinyl etc.)
which have araised pattern, are easily affected by
heat. They may, therefore, scorch or become
discoloured when close to a heating appliance.
Please bear this in mind when having a heating
appliance installed and when redecorating.
PLEASE NOTE
When operating your fire for the first time, some vapours may be given off which may cause a slight odour and could possibly set off any
smokealarms in the immediate vicinity. These vapours are quite normal with new appliances.They are totally harmless and will
disappear after a few hours use. This fire is supplied with ceramic “coals” to simulate a real coal fire. These items are designed for easy
refitting if removed.

4
GAS CONSUMPTION
Model637 has a maximum natural gas input of 6.85kW (Gross)
OPERATING THE FIRE
The flame sensing device.
For your safety, this appliance is fitted with a device which will automatically shut off the gas supply to the fire if the pilot
flame goes out. It will also shut off the gas supply if the flue is blocked or if there is not enough ventilation. If this device
starts to frequently shutoff the gas, get expert advice.
This device incorporates a probe which senses that the heat from the pilot flame is correct. If this probe is cool, the device
will prevent any gas flow unless the control is held at the ignition position.
If, for any reason, the flames go out when the fire is hot or if the fire is turned off when hot, always wait at least three
minutes before attempting to relight.
To light the fire
Rotate the control to the pilot positionand
depress. Press the piezo button repeatedly.
There may be a delay before the pilot lights
due to airbeing purged from the system.
Whenthe pilot burner is operating properly,
gradually turn the control knob anti-
clockwise to HIGH (Depress the knob
slightly to get past the LOW position). The
main burner should now light. Depress the
control knob slightly to release from the
HIGH position and turn back (clockwise) to
LOW. While turning, the burner flames
should gradually become lower but remain
alight. Depress the control knob slightly to
release from the LOW position and turn
back (clockwise) to IGN. The main burner
should extinguish but the pilot should
remain alight. Depress the control knob
slightly and turn back (clockwise) to turn
OFF this will extinguish the pilot. See fig 1. Fig. 1 – Lighting the Fire

5
CLEANING
Turn the fire off and allow it to cool before attempting any cleaning. Note that the fire will retain heat for some time after
it has been turned off.
If large pieces of debris are found anywhere in the fireplace, have the chimney inspected before further use.
Metal parts
Clean the metal parts with a slightly damp cloth and then dry. Do not use abrasive cleaners, they could scratch the surface.
Coals
This product uses fueleffect pieces and burner compartmentwalls containingRefractory Ceramic Fibres (RCF), which are
man-made vitreous silicate fibres. Excessive exposure to this material may cause temporary irritation to eyes, skin and
respiratory tract. Consequently, it makes sense to take care when handling these articles to ensure that the release of dust is
kept to a minimum.
Light coatings of soot will usually be burnt off during the normal operation of the fire. Should any soot accumulation
become excessive,the fuel effect pieces and walls should be removed from the fire for cleaning. Cleaning shouldbe carried
out in a well ventilated area or in the open air by gently brushing with the pieces held away from your face so that you
avoid inhaling the dust. We do not recommend the use of a normal domestic vacuum cleaner which may blow dust back
into the air. We suggest that youremove the coals in the reverse order to that shown inthe fuel bed refitting instructions.
Ceramic burner
Remove any deposits of soot or other foreign matter from the solid areas of the burner with a dry soft brush. Be careful
not to brush any particles into the openslots.Remove any particles from theslots with a vacuum cleanerfitted with asoft
brush attachment. Do not poke wire, etc. into the slots in the burner.
FUEL BED REFITTING
If the fuel bed components are dislodged or removed, they must be refitted as follows:
Only the fuel bed parts supplied with this appliance or authorised Valor replacements must be used. Never add extra coals
above the number stated in these instructions.
Placement of the ceramic coal matrix.
Positionthe bottom rear face of the coal matrix resting on the angled ledge of
the coal matrix support plate located towards the back of the burnertray.The
bottom front edge of the coal base should locate behind the recess in the burner
plaques (See figure 2).
Place the ceramic front coals in positionin front of
the coal matrix.Make sure that the side legs ofthe
front coals are fully seated into the burner tray. (See
figure 3).
Fig.3 – Placing Front Coals
Fig.2 – Placing Matrix