Vantage Hearth HD 8000S User manual

HD 8000S
MANUAL
www.vantage-digital.com

Safety Instruction
2English 2
S afety Instructions
This product has been manufactured to satisfy the international safety standards.
Please read all of safety and operating instructions before operating the product and keep this
manual for future reference.
MAINS SUPPLY
AC 90-250V~, 50/60Hz
Operate your product only from the type of power supply indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your local power company.
Disconnect the STB from the mains before you start any maintenance or installation procedures.
OVERLOADING
Do not overload a wall outlet, extension cord or adapter as this may result in electric re or
shock.
LIQUIDS
The product should not be exposed to any liquids such as dripping or splashing. No objects
lled with liquids, such as vases, should be placed on the apparatus,
CLEANING
Before cleaning, disconnect the product from the wall outlet, Use a cloth lightly dampened with
water (no solvents) to clean the exterior.
VENTILATION
The slots on top of the product must be left uncovered to allow proper airow to the unit. Do not
stand the product on soft furnishings or carpets. Do not expose the product to direct sunlight,
place it near a heater. Do not stack electronic equipment on top of the product.
ATTACHMENTS
Do not use any attachment that is recommended by the manufacturer it may cause a hazard or
damage the product.
CONNECTION TO THE SATELLITE DISH LNB
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the LNB.
CONNECTION TO THE TV
Disconnect the product from the mains before connecting or disconnecting the cable from the
satellite dish. Failure to do so can damage the TV.
LOCATION
Place the product indoors in order not to expose to lightning, rain or sunlight.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplier) that product heat.
LIGHTNING, or NOT IN USE
Unplug the product from the wall outlet and disconnect the cable during a lightning storm or
when unused for a long time.
SERVICING
Do not attempt service that this product yourself, as opening or removing covers may expose
you to dangerous voltage or other hazard. Refer all servicing to qualied service personnel.
“The mains plug is used as the disconnect device. Then disconnect device shall remain
readily operable”

Contents
3
English
C ontents
Safety instructions ................................ 2
Chapter 1
Before You Begin................................... 4
General Features......................................... 4
Accessories ................................................. 4
PVR Functions............................................. 42
Comfort Functions ....................................... 44
Chapter 2
Controls and Functions ........................ 5
Front Panel.................................................. 5
Rear Panel................................................... 5
Remote Control Unit.................................... 6
Chapter 3
Connections........................................... 10
Location of your receiver........................ 10
Connecting your receiver with
dish system ............................................ 10
Connecting your analog receiver ........... 11
Connecting your receiver to TV.............. 11
Connecting your receiver to VCR
(depending on model) ............................ 11
Connecting external audio/Hi-Fi system ... 11
Connecting digital audio system ............ 11
Chapter 4
Initial Settings and Operations............. 12
Menu Information................................. 12
Getting Started..................................... 12
Selecting the On Screen Display (OSD)
Language ............................................... 12
Selecting the Antenna Setting................ 12
Auto Scanning........................................ 15
Auto Scanning (terrestrial) ..................... 16
Basic Operation ................................... 16
Switching Channel ................................. 16
Volume Control....................................... 16
Info Bar................................................... 17
Selecting the soundtrack........................ 17
Selecting the OSD teletext, VBI teletext,
Subtitle and DVB subtitle ....................... 17
Sleep Timer Function ............................. 18
Zoom Function ....................................... 18
Channel List ........................................... 18
To view channel list in specic order
(Alphabet/Satellite/Provider/HD)............. 19
Electronic Program Guide (EPG)........... 19
Chapter 5
Menu Map............................................... 20
Main Menu.............................................. 21
Installation............................................ 21
Antenna Setting...................................... 21
Motor Setting.......................................... 23
Auto Scanning........................................ 26
Manual Scanning ................................... 26
Blindscan................................................ 28
Defaults Setting...................................... 29
System Setup....................................... 29
Language Setting................................... 29
OSD Setting ........................................... 30
Video Setting.......................................... 30
Audio Setting.......................................... 31
Time Setting ........................................... 31
Reservation Setting................................ 32
System Information ................................ 32
Channel Setup ..................................... 33
Delete Channels..................................... 33
Delete All Channels................................ 34
Favorite Channels.................................. 34
Edit Channels......................................... 35
Software Manager.................................. 36
Parental Lock....................................... 36
Channel Lock ......................................... 36
Lock Controll .......................................... 37
Change Pin Code................................... 37
Game ................................................... 37
Multimedia............................................ 38
PVR Setting............................................ 38
Player Setting......................................... 38
Internal Harddisk.................................... 39
USB 1 and 2........................................... 39
Ethernet.................................................. 40
Conditional Access............................... 41
PVR Functions..................................... 42
Comfort Functions................................ 47
Troubleshooting .................................... 48
Specications ........................................ 49
Glossary ................................................. 52
HDD Installation Guide.......................... 55

Chapter 1 Befor You Begin
4English
B efore You Begin
General Features
• Accurate, Brilliant Friendly OSD with Full Function
• MPEG-2 (MP@ML), MPEG-2 (MP@HL), MPEG4 AVC/H.264, HP@L4
• LNB Controlling Logic (0/22KHz Tone)
• SCPC/MCPC Receivable from C /Ku-Band Satellites
• Digital Tuner with Loop-through
• Wide Symbol Rate 2~45Mbps & Frequency Input 950~2150MHz
• DiSEqC 1.0, 1.1 & 1.2 Supported (Go to X function)
• 2 SCARTS for TV, VCR (optional)
• 16 Bit Colors Graphic User Interface
• Multi-language Menu
• 13-digit VFD (Time clock in Stand-by mode)
• OSD Teletext Supported
• EPG (Electronic Program Guide) for On-screen Channel Information
• Installation by Easy Setup Guide
• 10,000 Channels
• User-friendly Data Editing Function
• Favorite Channel and Parental Lock Function
• RS232C Port for Additional Information Service and Upgrading System Software
• S/PDIF OUT Optical and Coaxial
• HDMI
• SVIDEO OUT
•
PVR Ready
• Time-Shift
• Unicable
• OTA Update for Software and Channel Data
• Ethernet Port(Just HD7100 Series)
• USB Port
• 2 Common Interface and 2 Smart card Reader
• SW Blind scanning function
Accessories
• User’s Manual, Micro ber towel, Vantage CD-Rom
• Remote Control Unit
• Batteries
• HDMI Cable

Chapter 2>> Controls and Functions
5
Engllish
1
2
3
4
5
6
9
10
1 1
12
13
14
15
7
8
C ontrols and Functions
Front Panel
1
Power ( ) button
Turns your receiver On/Off.
2
Arrow (◄/►)buttons
Adjusts the volume and moves the cursor
left/right on the menu
3
Arrow (▲/▼)buttons
Changes channels or moves the cursor up/
down on the menu.
4
MENU button
Displays the menu
Exits from the current menu or goes to the
previous menu
5
OK button
Conrms selection
6
DISPLAY
Displays channel information
Displays local time in Standby mode
Rear Panel
1
Dish INPUT Tuner2
Connects to the satellite dish.
2
Dish INPUT Tuner 1
Connects to the satellite dish.
3
LOOP
Loop out is an output port of the DISH
INPUT signal.
4
USB 1
Connects to the External HDD or USB
storage with USB cable.
5
RS-232C
Connect to a PC.
RS232 transfers data to the external
computer.
6
USB 2
Connect to a PC..
7
VIDEO OUT
Connects to video input jack on TV or any
external Video system.
8
AUDIO OUT, LEFT / RIGHT
Connects to audio input jacks on TV or any
external audio system.
9
Y Pb Pr OUT
Connects to video input jack on TV or any
external Video system.
10
S-Video OUT
Connects to the TV with S-Video cable
1 1
S/PDIF OUT Optical & Coaxial
Connects to a digital audio component with
optical cable.
12
Ethernet(Optional)
Connects to the Ethernet with Ethernet cable
13
HDMI
Connects to the TV with HDMI cable
14
SCART for VCR
Connects to the VCR(AUX) with SCART
cables.
15
SCART for TV
Connects to the TV with SCART cables.

Chapter 2>> Controls and Functions
6English
Remote Control Unit
1
Power Button for TV and STB
Switch TV or STB On or OFF.
2
Nummeric (0~9) Buttons
To access channels directely via channel
number.
3
Mute ( ) Button
Mute the sound.
4
Sleep ( ) Button
Starts sleeptimer function.
5
Option Button
To access multifeed channels
6
OK Button
To access channel list or conrm/ select in
menu mode.
7
Text Button
Starts teletext service.
8
Last Button
Shows a list of last viewed channels
9
MoSAic ( ) Button
Opens Multi picture mode
.
10
Audio ( ) Taste
Zeigt die Audio Informationen an.
1 1
Arrow (◄/►)Buttons
Control Volume and in menu mode move
cursor left or right.
Arrow (▲/▼)Buttons
Changes channels up or down and move cusor
up or down in menu mode.
12
Guide Button
Opens EPG mode.
13
Media Button
Opens your lelist.
14
Zoom ( ) Button
To zoom in the picture, press twice for higher
zoom
15
Menu Button
Opens main menu .
Move back to the latest menu levelor close
menus..
16
Info Button
To show channel infomations on the Screen.
17
Back Button
Back to last menu level. Dont forget to store!!.
18
SAT ( ) Button
Shows a list of available satellites.
19
VOl +/- Buttons
Controls the Volume.
20
Page (+/-) Button
Jumps page wise up or down in TV or Radio
list.
21
FAV Button
To select one of your Fav lists. Press multiple
times to go thru all your Fav lists and back to
main list.
22
REW<< Button
Rewind in playback mode up to 8 x speed.
23
PR +/- Button
Channel change up or down.
24
Stop Button
stopps recordings or playbacks.
25
Record Button
Instant record
26
Play/ Pause Button
Shows your lelist, pause playbacks and start
playbacks
.

Chapter 2>> Controls and Functions
7
Engllish
27
FWD>> Button
fast foward up to 16 x speed in playback.
28
PiP Button ( Picture in Picture )
Starts PiP Feature.
29
Timer Button
Opens Reservation Menu.
30
Timeshift Button
Starts Timeshift Function.
31
Mode ( ) Button
Switch between TV and Radio mode.
Video Format Button
Opens a menu to change TV Aspect Ratio
Swap Button
Switch from PiP to full screen.
Pause Button
Pause and paylback again in playback
mode.
Remote Control Unit

Chapter 2>> Controls and Functions
8English

Chapter 2>> Controls and Functions
9
Engllish
Additional function
1. Learning Method
• If there is no further action within 30 seconds in LEARN MODE, the remote control turns to
normal operation mode switching LED off.
• TV Power key doesn’t have Default key data.
The Learning Method
• Only the key of “TV Power”has Learning function.
• Toggle Learning (Continuous 2 codes should be learned in TV Power key)
• 1st Learned data is produced upon 1st press and then 2nd Learned data will be produced
upon next pressing on the TV Power key.
If you press [TV Power + OK] KEYs at the same time for 1.5 seconds, the remote goes into
leaning mode. => Then LED ON will be “ON’ for 30 seconds. If there is no further action, it
will automatically turn back to normal mode after 30 seconds switching LED off.
Press TV Power key one more time. LED blinks one time and then LED will be “ON”.
Press 1st SOURCE KEY (Power key of the original key)
If it learns correctly, --- LED will be “ON”after blinking Two Times.
- If it does not learn correctly, --- LED will be “ON” after blinking 5 Times
- If there is no input Signal for 30 seconds, the remote will stay in learning mode after
blinking 5 times.
- If no further input signal for another 30 seconds, the remote will return to normal operation
mode. LED will be OFF.
- If you want to teach it again, then you need to press TV Power key. --- LED will stay
“ON”after blinking one time.
Now you learned one code from your original TV power key. Please press TV Power key
one more time. --- LED will stay ON after blinking one time.
=> If the rst TV Power code is learned correctly (after LED Blinking two times), 2nd code
can be taught.
Please press 2nd SOURCE KEY(Any numeric key from the original remote control. For
example Number 1)
If it learns correctly, --- LED will be “ON” after blinking Two Times.
If it does not learn correctly, --- LED will be “ON” after blinking 5 Times
=> If there is no input Signal for 30 seconds, the remote will stay in learning mode after
blinking 5 times.
If no further input signal for another 30 seconds, the remote will return to normal operation
mode. LED will be OFF.
=> If you want to teach it again, then you need to press TV Power key. --- LED will stay
“ON” after blinking one time.
If you press [TV Power + OK] Keys at the same time, it turns back to normal operation
mode after LED blinking 3 times.
2. Low Battery Warning Function
It is the fuction to check if the battery has LOW VOLTAGE
If you press [STB Power] KEY at the level that IC’s OPERATING VOLTAGE is as low as
“2.2V ~ 2.3V”, power code will be produced blinking LED 3 times.
At that LOW VOLTAGE level, you can not go into LEARNING MODE.
Remote Control Unit

Chapter 3 >> Connections
10 English
C onnections
Location of your receiver
• Install your receiver in horizontal position
• Do not put any heavy stuff such as a TV on your receiver
• Do not install your receiver in the places as follows: Vibrating place, direct sunrays, Humid
place, too high or low temperature, and no ventilated place.
Connecting your receiver with dish system
After installing your antenna system, connect the coaxial cable from the LNB of your antenna to
“DISH INPUT” terminal marked at the rear panel of your receiver. All cable connectors should
be nger-tightened; do not use any kind of wrench while tightening connectors. The cable
should be 75 ohm impedance coaxial twisted at the end with an “F” type connector.

Chapter 3 >> Connections
11
English
Connections
Connecting your analog receiver
To facilitate the user using analog receiver to view analog channels, this product has been
provided with a loop through terminal marked as “Loop”. Connect the coaxial cable from this
terminal to the IF input terminal of your analog receiver. Now by keeping your receiver in
standby, you will be able to tune and view analog channels from your analog receiver.
Connecting your receiver to TV
To connect your receiver with your television, you can use 4 different methods; via RCA cable,
SCART cable, HDMI cable or YUV.
Connect the RF cable to the terminal marked “RF OUT” on the rear panel of your receiver and
its other end to the TV RF input socket.
Connect the Video/Audio RCA cables from the Video OUT/AUDIO OUT (LEFT, RIGHT) on the
rear of your receiver to the Video INPUT/AUDIO INPUT (LEFT, RIGHT) jacks on the TV. In the
case of connecting your TV through SCART cable, connect the SCART connector marked TV to
the respective SCART port on the TV. (depend on model)
Connect the HDMI cable to the terminal marked “HDMI” on the rear panel of your receiver
and its other end to the TV HDMI input.
Connecting your receiver to VCR (depending on model)
To connect a VCR, your receiver has been provided with SCART at the rear marked “VCR”.
Using a SCART connector, the VCR can be connected to your receiver.
Connecting external audio/Hi-Fi system
To connect any external Audio Hi-Fi system, your receiver has been provided with two RCA
connectors at the rear panel of your receiver, marked with AUDIO L and R respectively to
connect the left and right Audio on the external audio/Hi-Fi system.
Connecting digital audio system
Connect a cable between S/PDIF OUT at the rear panel of your receiver and S/PDIF INPUT
COAXIAL or OPTICAL on the Digital Audio System.

Chapter 4 >> Initial Settings and Operations
12 English
I nitial Settings and Operations
Menu Information
A menu is a eld of text shown on the TV screen. Selectable lines are generally activated
(highlighted). No-activated lines cannot be selected. Most of menus show short information at
the bottom of the screen.
This menu consists of 7 main menus:
• Installation • Game
• SystemSetup • Multimedia
• ChannelSetup • ConditionalAccess
• ParentalLock
1 Using the Arrow (▲/▼)buttons you can move upwards and downwards on the menus.
On the menus, you can search channels using this button.
2When you have reached the required subject menu, press the OK button to conrm your
choice.
3On the menus, you can select menu items using the Arrow (◄/►)buttons.
4When you want to return to the previous menu with saving the change, press the Back
button.
5When you want to exit from the current menu, press the Menu button.
Getting Started
To start your receiver for the rst time, you must select the language for displaying menus
and you should set parameters for system conguration and scan satellite channels. Perform
the following setup procedure for scanning the satellite. Follow the instructions below to scan
satellite channels. You can enjoy watching TV or listening to the Radio after the procedure
completes.
1 Turn on your TV and receiver.
Language Setting menu will appear automatically.
OSD Language is highlighted.
Selecting the On Screen Display
(OSD) Language
2Select the OSD language of your choice using
the Arrow (◄/►)buttons.
You will see the selected language on the OSD
menu.
3Select Installation using the Arrow (◄/►)
buttons.

Chapter 4 >> Initial Settings and Operations
13
English
Getting Started
Setting the Clock
1Select the desired time zone using the Arrow
(▲/▼)buttons
2Select if you want to use daylight saving time
using the Arrow (▲/▼)buttons. Select between
On and Off
3Press the blue button to continue.
Antenna Setting Tuner 1
You can set antenna and LNB information for
scanning channels. If antenna is not correctly set,
you cannot scan channels, therefore you cannot
watch any programs.
1Select Antenna Setting using the Arrow (▲/▼)
buttons and press the OK button.
Antenna setting menu appears.
2Select satellite for channel scan using the Arrow
(▲/▼)or Page (+/-) buttons and press the
Arrow (◄/►)button to select at option.
3Select an option using the Arrow buttons.
LNB Power: On or Off (Defaulf: Off)
Longitude: Using Defaultmode
LNB Type: Universal 1, Universal 2 (Default
Universal 1)
LNB Freq: Frequency can be input with
numeric key with RCU
DiSEqC Port:1~4 for 1.0 and Tone Burst 1~2 and Off.
Tone 22kHz: On, Off or Auto (Default: Auto)
Unicable:
Press OK Button to choose one IF by Auto detection
Motor: Moving Antenna unsing DiSEqC1.2 or USALS
DiSEqC1.1: Uncommited DiSEqC Command 1-16

Chapter 4 >> Initial Settings and Operations
14 English
Antenna Setting Tuner 2
1Select Antenna Setting for tuner 2 using the
Arrow (▲/▼)buttons and press the OK button.
2Select one of the following options:
Same Signal: Same conguration as tuner 1
Loop Through - Cable from tuner 1 loop through
tuner 2
Separated: Tuner 2 has a different connection.
After selecting this options the same menu as
tuner 1 comes up and you have to select the
options.
Installation Options
1Select one of the following options using the Arrow (▲/▼)buttons.
Option 1: Auto Scanning see page 15)
Option 2: Download Channel list from Astra
You can select from different channel lists. Select you desired list and press OK Key.
Option 3: German Channel list
2 Press OK Key.
Getting Started

Chapter 4 >> Initial Settings and Operations
15
English
Auto Scanning
1Select Auto Scanning using the Arrow (▲/▼)
buttons and press the OK button.
The preprogrammed satellite lists will appear.
2Select an appropriate satellite using the Arrow
(▲/▼)buttons and set the channel options
using the Arrow (◄/►)buttons.
• Off: Scanning is disabled.
• All: Scan all the free and scrambled
channels.
• Free: Scan free channels only.
• NIT: Scan all mode with TP network scanning.
• You can set Off, All, Free or NIT to each satellite.
3Press the OK button, Auto Scanning will start.
All the channels in the list from the selected satellite will be automatically downloaded.
4Press the OK button to save the changes.
5Press the Back ( )button to exit from the menu
and press the Arrow (▲/▼)buttons to select the
desired channel. Now you can watch TV or listen
to the Radio.
For more information on scanning a satellite see chapter 5!!
Getting Started

Chapter 4 >> Initial Settings and Operations
16 English
Terrestrial (optional) Auto
Scanning
1 Press OK Key to start Auto Scanning.
2 Press the OK button to save the changes.
3 Press Back Key button to exit from the menu
and press the Arrow (▲/▼)buttons to select
the desired channel. Now you can watch TV
or listen to the Radio. You can no select the
channel using arrow buttons (▲/▼)
Basic Operation
This section explains various functions while watching TV or listening to the Radio.
Switching Channel
You can switch the current channel by three different methods.
• Method 1: Press the Arrow (▲/▼)buttons or PR+/- buttons.
• Method 2: To select a channel directly, select a channel using the Numeric (0~9) button.
• Method 3:
1To display the channel list, press the OK button.
2Select a channel you want to watch using the Arrow (▲/▼)buttons and then press the OK
button.
• If there are multiple channels, use the Page (+/-) or the Arrow (◄/►)buttons to move to
channels by page.
• Press the Mode ( ) button to switch between the TV and Radio channel.
• Method 4: In case of more than two scanned satellites
1Press the SAT( ) button to show satellite list.
2Move the cursor to the satellite of a channel to watch with the Arrow (◄/►)buttons and
then press OK button.
3You can follow the method 3 instruction for channel selection.
• Method 5: How to move to the watched channel.
1Press the last button with RCU.
2Press OK button after a channel selection by using the Arrow (▲/▼) with RCU.
3Press OK button to exit.
Volume Control
To control the volume:
• Press the VOL+/- or the Arrow (◄/►)buttons.
• Press the Mute ( )button to turn the sound off.
• Press the Mute ( )button again or the VOL+/- or Arrow (◄/►)buttons to cancel muting.

Chapter 4 >> Initial Settings and Operations
17
English
Info Bar
Channel information always appears for a specic period of time whenever you switch
channels.
General Information
Press the INFO button; you can see general information of the current channel.
1
Channel number and name
2
Current time
3
Signal Level
4
Signal Quality
5
Icons: HD channel, Locked channel, Radio Channel, Scrambled channel, Subtitle, Teletext
information
6
EPG information.
7
Conditional Access
Detailed Channel Information
You can see detailed channel information pressing the INFO ( )button again.
8
You can see detailed channel information pressing the INFO button again.
9
Satellite, Frequency, Symbol Rate, FEC, Polarity, Video PED, Audio PID, PCR PID,
Transponder
10
Display the stream information.
Selecting the soundtrack
You can select the audio language, soundtrack, or
sound mode.
1Press the Audio (Yellow) button.
2Press the Arrow (▲/▼)buttons to select the audio
language or soundtrack and press the OK button.
3Press the Arrow (◄/►)buttons to select the
sound mode from Stereo, Mono left, or Mono
Right.
4Stream information.
Selecting the OSD teletext, VBI teletext, Subtitle and DVB subtitle
You can choose the OSD teletext, VBI teletext, subtitle and DVB subtitle for the current live
TV program if provided from the broadcasting station.
• OSD teletext: Press the Text button
• VBI teletext: Press the Text button twice.
• Subtitle: Press the Text button three times.
• DVB subtitle: Press the Text button four times.
Basic Operation

Chapter 4 >> Initial Settings and Operations
18 English
Sleep Timer Function
Press the GREEN (Sleep) button, you will see the time set for the sleep timer if already set from
the Time Setting menu.
Zoom Function
You can make the picture appear larger on the screen pressing the Zoom ( ) button.
1Press the Zoom ( )button.
2Select the area you want to zoom using the Arrow buttons and then press the OK button.
Picture is enlarged two times.
3Each time you press the Page (+/-) buttons, the
picture is enlarged two or four times.
Press the Arrow (▲/▼/◄/►) buttons to change
the location at the lower right of display.
4To cancel the Zoom function, press the Zoom (
)button twice or Back button.
Channel List
You can see the TV or Radio channel list pressing
the OK button while watching TV or listening to
the Radio. Switch the channel list pressing the Mode ( )button. The icons behind channel
names reect the status of the channel like scrambled or locked.
Select channel using the Arrow (▲/▼/◄/►), PR+/-, or Page (+/-) buttons and press the OK
button to watch.
The colored buttons show the channel lists as follows:
• RedKey: sort channel alphabetically
• GREEN button: by satellites
(all/searched satellites)
• YELLOW button: by names of broadcasting
providers
• Bluebutton: by HD channels
• Opt: Enter channel list menu to move, delete or
rename channels
Basic Operation

Chapter 4 >> Initial Settings and Operations
19
English
To view channel list in specic order
(Alphabet/Satellite/Provider/HD)
1Press the Colored (Red/ Green/Yellow/Blue)
button.
Channel list is highlighted.
2Select Alphabet, Satellite, Provider, or HD
using the Arrow (▲/▼)buttons.
The channel list is sorted automatically by your
selection.
3Select the channel pressing the Arrow (▲/▼)
or Page
(/)buttons and press the OK button to
watch it.
Electronic Program Guide (EPG)
EPG displays program information such as program titles, broadcasting schedule,
Program synopsis and such EPG service differ depending on the service provider.
1Press the GUIDE button while watching TV or listening to the Radio EPG information
appears.
2Select a program for further more information.
• Arrow (▲/▼)buttons: Selects a program by channel
• Arrow (◄/►)buttons: Selects a program by time & date within the same channel.
It displays the program list at 30 minutes intervals.
• You can see the detailed information by pressing Page (+/-) buttons with RCU.
3
. Press the OK button, detailed information on the selected event appears.
4Press YELLOW Key to switch Viewmodes in EPG (Multi vs. Single Channel).
5To jump one day ahead press BLUE KEY.
6To jump one day back press RED KEY.
7To record a transmission press GREEN KEY.
Read more in the PVR-Chapter !!
8To exit from the EPG mode, press the Back button
Basic Operation

Chapter 5 >> Main Menu
20 English