VarTech Systems DiamondVue VT201C User manual

VT201 DiamondVue User Guide 150-021
VT201 DiamondVue Series
20.1” Flat Panel Series LCD Monitors
VT201C · VT201R
VT201P · VT201PSS
VT201W · VT201M · VT201MF
Transflectives:
VT201CTSR · VT201PTSR
VT201PSSTSR · VT201RTSR
VarTech Systems Inc.
Solutions for Demanding Applications
Industrial CRT and Flat Panel Displays
User’s Guide
Read these instructions completely before attempting to operate your new Color Display.

Table Of Contents
Page Page
Section 1 Section 4
Introduction 1 Touch screen 10
1.1 About LCD Monitors 1 4.1 Introduction 10
1.2 Product Safety Precautions 2 4.2 Installation 10
Section 2 Section 5
Display Setup 3 Troubleshooting Tips 11-12
Display Features 3
2.1 Unpacking The Display 4 Section 6
2.2 Included Parts 4 Cleaning & Maintenance 13
2.3 Connecting Your Display 4
2.4 Signal Connections 4-5 Section 7
Mechanical Drawings 14
Section 3 7.1 Panel Mount Procedure 14
Getting Started 6 20.1” Chassis Mount Mechanical Drawing 15-18
3.1 Adjusting the Display 6 20.1” Panel Mount Mechanical Drawing 19-20
3.2 Adjustment Procedure 7-9 20.1” Rack Mount Mechanical Drawing 21
20.1” Wall Mount Mechanical Drawing
20.1” Foxboro Configured Mechanical Drawing 22
Section 8
Display Specifications 23

VT201 DiamondVue User Guide 150-021
LCDs
INTRODUCTION
INTRODUCTION
1
Section
About LCD Monitors
What you gain by using an LCD monitor in your industrial controls
are the future of display technology. CRTs although they have
dropped in cost significantly, do not offer the performance, reliability,
and mounting options available with LCDs. LCD monitors consist
primarily of an LCD, Video Board and a Back Light video. The LCD
determines to a large extent the viewing angle, brightness and contrast. Beyond that it is the
function of the video board which converts the analog RGB (Red, Green, Blue) signals from a
standard video card to a high quality, digital RGB that the LCD can display.
Recently the video card has taken on a new role. It is the responsibility of this device to “scale” a
particular video resolution to the “native” resolution of the LCD. Simply, consider that a computer is
putting out a VGA [640x480] resolution signal, yet the LCD that is connected is an XGA
[1024x768] display. The displayed picture would be in the center 1/3 of the LCD. With the
introduction of the scaling engine. The converter will mathematically recalculate the 640x480 to
1024x768. This may sound simple but it is in fact a complex algorithm that adjusts for different
aspect ratios and pixel alignment, essentially smoothing text and graphics to produce a picture
that is pleasant to the eye.
All Vartech displays from 12.1” (800x600) to 23.1 (1600x1200) incorporate scaling engines in the
converter card.
1.1
1

Product Safety Precautions
 Ensure that sufficient space is available around the display to provide the circulation
necessary for cooling.
 Ensure that the ambient air temperature will not exceed the specified maximum
temperature.
 Do not attempt to service this display yourself. The rear chassis has a seal so that non
qualified personal will not expose themselves to dangerous voltages or other risks.
 To protect from electrical shock, unplug the display power supply from the wall before
moving.
 Do not expose the display to direct sunlight or heat.
 Do not use this display near water
 Do not place any heavy objects on the power cords. Damage may cause electrical shock.
 Unplug the power supply from the wall or unit if one of the following conditions exists.
 Power cord or plug is damaged or frayed
 Liquid is spilled into the display or the display is exposed to rain or water.
 The display does not operate normally when the operating instructions are
followed.
 The display has been dropped or the enclosure has been damaged.
 The display exhibits a distinct change in performance, indicating a need for
service.
1.2
2

VT201 DiamondVue User Guide 150-021
Section
2 DISPLAY SETUP
DISPLAY SETUP
VT201 Series Display Features
 Capable of displaying unlimited colors in a continuous spectrum. The high contrast LCD
enhances the image with no geometric distortion.
 The VT201 DiamondVue Series directly accepts an analog 5 wire RGB with separate H/V sync
or 4 wire RGB with separate combined sync or 3 wire SOG.
 The VT201 DiamondVue Series is auto synchronous adjusting the display to the appropriate
input between VGA, SVGA,XGA, and SXGA.
 The VT201 DiamondVue Series is supplied with a Anti-Reflective Screen unless equipped with
an optional Touch System.
 The VT201 DiamondVue Series has an integrated 115/220VAC or 90/264VAC supply as stan-
dard on all models.
2.1
3

 VT201C, VT201P, VT201P-SS, VT201R, VT201MF, VT201W, VT201M LCD Monitor or
VT201CTSR, VT201PTSR, VT201PSSTSR, VT201RTSR Transflective
 5 ft Video Cable
 10-32 Mounting Hardware. (For use with Panel Mount only)
 6 ft RS232 or USB Touch Interface Cable (Optional when touch is installed)
 CD ROM with Touch Screen Drivers (Optional when touch is installed)
 Users Guide (Printed or on CD)
2.2 Unpacking and setting up your display
Your LCD monitor package will consist of the components listed below. Open shipping
container and lay all components on a flat clean surface.
2.3 What is included with your display
2.4 Connecting the Display
4
1. Connect all cables to the computer first. This would include the VGA cable and the optional
RS 232 serial or USB touch screen connection.
2. After connecting the cables between the LCD monitor and the computer, plug the customer
supplied +12VDC or 90/264 VAC source to the 12V connection on the rear.
3. Once the +12V connection is made, the display is active.
4. If your computer was off, turn on your computer.
5. Your display should now operate as a normal computer display showing your windows or
whatever video is being sent to the flat panel.
Note: If for any reason the display goes blank and gives an “out of Range” or “No Input Signal”,
your computer or video source is putting out a signal that is out of range of the LCD’s video
board. If this happens, reboot the computer or video source and make sure you are inputting
the correct signal. If the display doesn’t work properly, it may be because:
(a) The resolution is to high or low for the LCD.
(b) The refresh rate is set to high. Refresh on an LCD is different than a CRT. Set the refresh to
60Hz. CRT’s need a high refresh rate to avoid flicker. The refresh rate has no impact on
LCD’s.
(c) The power source is incorrect.
(d) The unit is malfunctioning. If you believe this to be true, disconnect the video cable from the
rear of the LCD and connect to a known good computer CRT display. If the computer
display is working satisfactory and the video is within the appropriate range, then contact
Vartech Customer service for a RMA number at 800-223-8050.
2.5 Signal Connections
To avoid irregular operation and /or damage to the display, please insure correct video is being
supplied as shown on the following page.

VT201 DiamondVue User Guide 150-021
2.5 Signal Connections Cont.
5
Standard Resolution Supported
 640 x 480 (VGA)
Pin assignments for the HD15
video connector.
Pin
1 Red Video
2 Green Video
3 Blue Video
4 Not Used
5 Return
6 Red Video Ground
7 Green Video Ground
8 Blue Video Ground
9 No Connection
10 Sync Ground
11 Not Used
12 Bi-Directional Data
13 Horizontal Sync
14 Vertical Sync
15 Data Clock (SCL)
Composite Video Input Connector: CVBS 1.0V p-p
S-Video: S-VHS
LUMA Signal Input 0.7V p-p
CHROMA Signal Input 0.7V p-p
You can use an HD-15 connector cable or a BNC adapter cable to connect the flat panel
monitor to the host computer. The HD-15 video cable (supplied in the kit) you use with this
monitor is equipped with a conventional HD-15 connector at each end.
Note:
The following figure is the view looking into the pin end of the male connector or solder term
end of the female connector.

Optional BNC Adaptor Cable
A 5BNC-to-HD15 adapter cable is available. The functions of the cables are described below.
 R, B, and G: Red, Green, and Blue input connectors to establish color.
These are used for RS-343 analog signals.
 HS/CS: Separate horizontal/composite sync signal from the video
source.
 VS: Separate vertical sync signal from the video source.
BNC Adapter Cable
This table describes the signal types you can use with the connectors:
2.5 Signal Connections Cont.
6
BNC Signal Type Description R G B HS/ CS VS
Sync-on-Green
(Not Available)
Use the three video connectors.
Horizontal and vertical syncs are
supplied on the green video line. X X X
Composite Sync
(Not available)
Use the three video connectors
plus the horizontal sync/
composite sync input X X X X
Separate Horizontal
and Vertical Sync.
Use the three video connectors
plus the horizontal sync/
composite sync and vertical sync
input.
X X X X X
BNC Signal Types

VT201 DiamondVue User Guide 150-021
Vartech Systems, Inc
Menu Select Down Up Input
3
Section
3.1 Adjusting the display
The VT201 DiamondVue Series display has an embedded microprocessor in the converter
card. Once you have the unit displaying the resolution you desire for your application do the
following:
In order to navigate to the appropriate adjustments, press Menu and the OSD layout chart will
appear as indicated as shown below.
Definition of OSD (on screen display) Adjustments
There are seven membrane buttons (as shown above) located on the unit. They will activate
the OSD and allow navigation to all adjustments if your unit requires adjustment.
Press MENU and a major adjustment category will appear. Press DOWN or UP and you will
see the remaining adjustment categories. The actual adjustment categories are listed under
each major category (bold) as shown below.
ADJUSTMENT
Brightness, Contrast, Clock, Phase, H Position, V Position, Auto
COLOR ADJUSTMENT
User, 6500, 9300
SETUP
Language, Image Size, OSD H Position, OSD V Position, Transparency, Zoom
PIP - Picture in Picture
PIP On / Off, PIP Source, PIP Size, PIP H Position, PIP V Position, PIP Image
7
3.2
GETTING STARTED GETTING STARTED

TOUCH SCREEN
TOUCH SCREEN
10
4
Section
Touch screens are a common means to interface operator inputs to a system. The universal
standard of Windows GUI (Graphical User Interface) has significantly increased the use of
touch screens.
There are four main touch technologies. The technologies are resistive, surface acoustic
wave (SAW), capacitive, and infrared (IR). Each touch technology has advantages and
disadvantages based on different user applications.
All Vartech Systems displays configured with a touch screen are supplied with a CDROM
which includes user manuals, application software, and drivers for various operating systems.
Insert the supplied CDROM into a CDROM drive and follow the installation instructions that
will appear on the screen.
Limited technical support is available by contacting Vartech Systems customer support at
800-223-8050.
4.1 Introduction
4.2 Installation

VT201 DiamondVue User Guide 150-021
11
Trouble Troubleshooting Tip
No Picture  The signal cable should be properly connected to the
display card and computer.
 Try disconnecting the video cable from the display and
connecting to a CRT display if available to confirm the
presence of proper video.
 Make sure power is connected to the proper DC or AC
source.
 Make sure the resolution mode is supported by the display and
check settings of the display card.
 Confirm that the video cable is not defective.
Image Persistence Image persistence occurs when a ghost of an image remains on
the screen after the monitor has been turned off. Unlike a CRT
monitor, an LCD monitor’s image persistence is not permanent.
To erase an image ghost, turn the monitor off for as long as the
image was displayed. If the image was on for one hour and the
ghost of the image remains, the display should be turned off for
one hour to erase the image. To avoid this problem, use a screen
saver.
Picture Quality & Image Stability  Check for proper video cable for proper grounding and
shielding.
 Check the signal source for proper signal.
 Check for proper adjustment of the Phase and Frequency
controls.
 Check for proper recommended signal timing.
Green LED not lit Check for proper power and power connections
Green LED blinking This indicates absence of video or proper video for this display
Display image is not properly
sized
 Adjust the Vertical and Horizontal size controls via the OSD.
(Reference setup adjustments)
 Ensure that a supported mode is selected on the display card
or system being used. Consult the display card or system
manual for proper video.
No S-Video or NTSC operation  Check for proper connections.
 Check the setup instructions for proper input selection.
If these tips do not solve your problem, contact Vartech Systems Customer Service support.
Troubleshooting
TROUBLESHOOTING
TROUBLESHOOTING
5
Section

12
Trouble Troubleshooting Tip
Screen is blank. Screen saver activated.
Video Cable problem. Check for proper installation
Change video cable .
Faulty video display. Needs Service.
Image is dim, even with
brightness and contrast
controls set full UP
Video cable problem. Check for proper installation of cables
Faulty video source.
Faulty display.
Image not centered Reset the horizontal and vertical positioning using the on-screen
menu. Check to see if video source is operating within the
monitor’s range
Image will not adjust Video timing outside of range. Use the on-screen menu to ad
just the Clock Setting.
Make sure timing is within VESA standard.
Image is not stable. Monitor has incorrect or bad sync signals.
Check for proper video cable installation.
Replace suspected faulty cable.
Check to ensure that video source is operating within the display’s
range.
Vertical shaded bars on
Screen image Horizontal size not properly adjusted. Adjust horizontal size settings
Colors are missing Faulty video cable.
Missing from video source.
Connect video source to another display
Screen jitter or noisy display
Troubleshooting Cont.
Monitor clock phase not properly adjusted
Slight distortion in text or
Graphics. Not working in native resolution.
Display is present but “bars”
Appear or roll across screen Ground loop problem between computer and display Interference from adjacent equipment
The background looks
Acceptable but text and
Icons seem to be missing
rows of pixels
Video running interlace mode.

VT201 DiamondVue User Guide 150-021
CLEANING AND MAINTANENCE
CLEANING AND MAINTANENCE
Cleaning
Occasionally clean the display panel and cabinet with a soft cloth dampened (not soaked) with a
mild (non-abrasive) glass cleaner. Keep turning a fresh side of the cloth toward the screen surface to
avoid scratching it with accumulated grit.
Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow
the screen to stand dry.
Special care should be taken when cleaning a touch screen or polycarbonate shield that is installed
over the screen. Abrasive and certain chemical cleaners can easily damage the surface.
Never use alcoholic or ammoniac cleaners to clean the polycarbonate shield or a touch screen.
Replacing a Line Cord
To avoid shock and fire hazards, the monitor’s power cord should be replaced if the insulation
becomes broken or if it develops a loose internal connection.
Other Maintenance
Qualified service personnel should perform all maintenance, except for the power cord replacement
described above.
13
Note:
The solvent should be applied only to the cloth, and not directly on the monitor screen.
Note:
For best results cleaning a monitor with the optional antireflective tempered glass display shield, a
solution of denatured alcohol is recommended to thoroughly clean the display.
6
Section

Panel Mounting Procedure
1. Cut and drill the panel (refer to panel mount drawing). Measurements are in inches.
Panel Mounting Cutout
2. If access to the side of the monitor is not available following installation, attach the power and video
cables to the side of the monitor at this time.
3. Install the monitor in the prepared cutout.
4. Install the lock nuts and washers, supplied with the monitor, behind the holes running along the sides
and top/bottom of the cutout in the panel. Extra lock nuts and washers are provided.
MOUNTING INSTRUCTIONS
MOUNTING INSTRUCTIONS
7.1 Panel Mount Procedure
14
7
Section
Mechanical Drawings
Model Description Page(s)
VT201C 20.1” DiamondVue Chassis Mount Mechanical Drawing 15-18
VT201P 20.1” DiamondVue Panel Mount Mechanical Drawing 19-20
VT201R 20.1” DiamondVue Rack Mount Mechanical Drawing 21
VT201W 20.1” DiamondVue Wall Mount Mechanical Drawing
VT201MF 20.1” Foxboro Configured Mechanical Drawing 22
Note:
Use #10-32 nuts for mounting.
5. Tighten all mounting nuts evenly to a torque of 24 inch-pounds.
ATTENTION: Mounting nuts must be tightened to a torque of 24 inch-pounds to provide panel seal and
avoid potential damage. Vartech Systems assumes no responsibility for water or chemical damage
to the monitor or other equipment within the enclosure due to improper installation.
6. Attach the power and video cables to the side of the monitor if you have not already done so.

VT201 DiamondVue User Guide 150-021
23
SPECIFICATIONS
SPECIFICATIONS
8
Section
ENGINEERING SPECIFICATIONS
Panel Size 20.1”
Type Active Matrix Color Thin Film Transistor (TFT)
Resolution Capabilities VGA to UXGA
Pixel Pitch .3075 mm
Active Display Area 16.21” x 12.20”
411.7mm x 309.8mm
Pixel Format 640 x 480, 800 x 600, 1024 x 768, 1280 x 1024, 1600 x 1200
Viewing Angle (Left/Right) 80/80 deg.
Viewing Angle (Up/Down) 80/80 deg.
Contrast Ratio 350:1
Brightness 201C, 201P, 201PSS, 201R, 201W, 201M, 201MF
250 Nits
Transflectives
over 1000 Nits*
Response Time TR= 12ms typical (22 max)
TF= 13ms typical (23 max)
Back Lights Cold Cathode 50,000 Hrs. Half Life
Video Connector HD15(F), DVI-I 29Pin connector (Digital/Analog)
Composite Video (CVSC), S-Video (S-VHS), RCA, mini din
Colors Supported 16.8M
Video Input RGB Analog (0.7V p-p / 75ohm) , Digital
NTSC / PAL, CVBS (1.0V p-p)
S-VHS, luma/chroma (.7V p-p / 75ohm)
Sync Separate H & V, Combined, SOG, Digital
Input Voltage 90-264VAC Universal
Power consumption 60 Watts
Operating Temperature 0 to 50ºC
Storage Temperature -20 to 60ºC
Operating Humidity 10 to 95%NC
Storage Humidity 10 to 95%NC
Operating Altitude Up to 10,000 ft
Storage Altitude Up to 40,000 ft
*Outdoor Brightness Equivalent (Varies depending upon sunlight brightness)

150-021-015
3.15.12
VARTECH SYSTEMS
HEADQUARTERS
11529 Sun Belt Ct.
Baton Rouge, Louisiana 70809
Toll-Free: 800.223.8050
International Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.vartechsystems.com