Vaughan 050012 Installation and operating manual
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE
AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS,
WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS
PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT,
DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT
AT 1-800-423-3598. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL
No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR
PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT, GIVE US A
Model #050012
Component #692527
100 Ft.
LASER DISTANCE METER
1
TABLE OF CONTENTS
INTENDED USE .............................................................. 1
GENERAL SAFETY RULES ...................................................... 1
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS ......................... 1
IMPORTANT SAFEGUARDS ............................................... 2
LASER SAFETY......................................................... 2
TOOL USE AND CARE ................................................... 2
FUNCTIONAL DESCRIPTION .................................................... 3-4
LCD INDICATIONS AND SYMBOLS ......................................... 3
LCD ERROR MESSAGES ................................................. 3
BUTTON FUNCTIONS.................................................... 3
BATTERY SYMBOL STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....... 4
BATTERY INSTALLATION/REPLACEMENT ......................................... 4
OPERATING INSTRUCTIONS .................................................... 4
TROUBLESHOOTING .......................................................... 5
MAINTENANCE .............................................................. 5
SPECIFICATIONS............................................................. 5
1-YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................... 6
FCC INFORMATION ........................................................... 6
INTENDED USE
This product is intended for consumer use only. It is designed to be used indoors and for non-contact distance mea-
surement.
GENERAL SAFETY RULES
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all
instructions in this manual may result in severe personal injury or death. Keep this manual and refer to it for
safety instructions and operating procedures.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
DANGER indicates an imminently hazardous
situation which, if not avoided, could result in death or serious
injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in death or serious
injury.
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
2
IMPORTANT SAFEGUARDS
WARNING: This product can expose you to chemicals known by the State of California to cause cancer
and birth defects or other reproductive harm. Wash hands after handling.
LASER SAFETY
Pointing a laser and interfering with the operation of an aircraft is
a felony punishable by fine and imprisonment.
The laser guide used in the tool is Class II.
The laser shall be used and maintained in accordance with the
manufacturer’s instructions.
The use of optical instruments with this product will increase eye
hazard.
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation ex-
posure.
Do not stare into the laser beam.
Never aim the beam at any person or an object other than the
work piece.
Avoid indirect exposure via reflective surfaces, such as glass and mirrors.
Store out of reach of children. Equipment should be in a high location or locked up to keep out of reach
of children. It is not a toy.
Do not tamper with the laser output. Changing the performance of the laser to increase its output is
prohibited. Any claim for damages or injuries resulting from not following these instructions will be refused.
Never operate laser if the unit is defective or the cover or seal is damaged.
There are no user-serviceable parts in the laser device. The laser unit must be returned to the
factory for any service or repair. Service or repair must be handled by authorized factory-trained technicians.
Be careful with this tool. Striking or jarring it, especially on the laser housing, can affect its accuracy.
TOOL USE AND CARE
Use the product only as specified in this manual.
Avoid exposing this device to EMF (electro-magnetic fields) from arc welders, induction
heaters, etc. OR exposing to static electricity.
To prevent sensor damage, do not point the sensor lens directly at the sun or any other
source of strong infrared light.
AVOID EXPOSURE
DIODE LASER CLASS II LASER PRODUCT
Alltrade Tools LLC Made in China
1 MW MAX OUTPUT
AT 630-680 nm
2 in. - 100 ft. (51 mm - 30.48 m)
LASER RADIATION-DO NOT
STARE INTO BEAM
MK7-30 (692527)
LASER RADIATION IS EMITTED
FROM THIS APERTURE
VISIBLE LASER RADIATION-DO NOT
STARE INTO BEAM OR VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CAUTION
Laser Distance Measure Label
3
FUNCTIONAL DESCRIPTION
LCD INDICATIONS AND SYMBOLS
1. Battery Status
2. Received Signal Strength
3. Laser On
4. Front Edge Measurement
5. Rear Edge Measurement
6. Unit (Foot, Inch, Metric)
7. Measured Distance or Error Message
LCD ERROR MESSAGES
BUTTON FUNCTIONS
Red Button: To turn on the meter and measure distance (single or continuous
measurement).
Black Button: To turn off the meter or to select options (Unit measurement or Front/
Rear edge measurement).
To convert the measured distance to other units of measurement, briefly press both red and black buttons at the
same time.
RED BLACK
Off/Options Button
On/Measure Button
LCD Display
Battery Housing (Backside)
Optical Receiver Lens
Hanging/Carrying
Lanyard
Laser Beam
Opening
2 AAA Batteries
Error Code Cause Solution
ERR01 The target the laser beam aims at is strong at
reflecting the laser beam.
Change the target or attach a piece of
white paper to the target.
ERR02 The distance to be measured is beyond the
measuring range. The specified measuring range
of this instrument is 2 in-100 ft (51 mm~30.48 m).
Measure within the effective measuring
range.
ERR03 The target the laser beam aims at is weak at
reflecting the laser beam.
Change the target or attach a piece of
white paper to the target.
ERR06 Low battery. Replace with a new battery.
4
BATTERY SYMBOL STATUS
“Battery Full”
“Battery Low”: Batteries MAY be replaced.
“Battery Empty”: Batteries MUST be replaced.
BATTERY INSTALLATION/REPLACEMENT
To install or replace the batteries:
1. In the back of the meter, gently slide the battery housing cover away.
2. Remove old batteries and insert two new AAA batteries according to the
battery direction markings inside the battery housing.
3. Reinstall battery housing cover.
4. Properly dispose of old batteries in accordance with local regulations.
OPERATING INSTRUCTIONS
Never aim the laser beam pointer at the eyes of a person or animal or
an object other than the work piece.
Pre-measurement setting:
1. To turn on the meter and laser pointer, briefly press the red button.
2. To set for desirable measurement units (inch, foot, metre), while
pressing on the red button, toggle between the measurement units
using the black button.
3. To toggle between front or rear edge measurements, briefly press
black button.
Measurement:
1. For single measurement:
a. Direct the laser at the target and briefly press the red button.
The distance to the target appears on the display.
b. For additional single measurements, press the red button to
clear the display and to turn on the laser pointer. Repeat step 1a.
2. For continuous measurement:
a. Direct the laser at the target and press the red button for 2
seconds until a clicking noise is heard. As you move toward
or away from the target, the distance to the target appears on
the display.
b. For additional measurements, press the red button to clear
the display and to turn on the laser pointer. Repeat step 2a.
Post-measurement:
• To convert the measured distance to other units of measurement, briefly press both red and black buttons at
the same time.
• To turn off the meter, press the black button for 2 seconds.
Front Edge Measurement
Rear Edge Measurement
Continuous Measurement
Distance
Distance
5
TROUBLESHOOTING
MAINTENANCE
•Clean the housing and the lens using only a soft cloth or cotton swab with water or medical alcohol.
•Do not let any liquid enter the case or sensor area. Allow the lens to fully dry before use.
•Avoid storing the meter in extreme temperature conditions. Do not store below 14°F (-10°C), or where the radiant
temperature may exceed 140°F (60°C).
•Always purchase the correct size and grade of battery most suitable for the intended use.
•Clean the battery contacts and also those of the device prior to battery installation.
•Remove batteries from equipment that is not to be used for an extended period of time to avoid damage to the tool
should the batteries deteriorate.
•Remove batteries if consumed or if product is to be left unused for a long time.
SPECIFICATIONS
Recommended Operating Environment: Indoor
Measuring Range: 2 in ~ 100 ft (51 mm ~ 30.48 m)
Measurement Accuracy:*+/- 2 mm (+/-0.079 in)
Minimum Display Unit (Metric) (Standard): (1 mm) (0.01 in.)
Laser Class: 2 (complies with FDA 21 CFR 1040.10 and
1040.11)
Laser Type: Maximum output power 1 mW,
Wavelength 630-680 nm
Instrument Auto-off Delay Time: 5 min.
Laser Auto-off Delay Time: 20-25 sec.
Battery Life (AAA alkaline battery): More than 5000 single measurements
Working Temperature: 14~104°F (-10~40°C)
Storage Temperature: 14~140°F (-10~60°C)
*IMPORTANT: Under adverse conditions (such as bright solar light outdoors or in the surrounding environment,
weak reflection of the surface to be measured, and rough surface), accuracy will be reduced.
Problem Cause Solution
The meter does
not turn on.
Batteries incorrectly inserted.
Low battery power.
Poor contact of the ON button.
Reinsert according to polarity symbols.
Replace with new batteries.
Press the button hard or send meter for
repair.
The meter clicks
inside.
It is a normal sound generated by the light
path switch-over device during measurement.
N/A
6
1-YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Every ALLTRADE®product is inspected before leaving the factory. This product is warranted to be free of defects in
material and workmanship for a period of one year from the date of original purchase. If a defect appears within one
year after the date of purchase, the purchaser may return the item, together with a purchase receipt or other appropri-
ate proof of purchase to the place of purchase. Upon receipt of the item(s), the place of purchase will, at its option,
replace the defective item or refund your money. This warranty shall not apply when the product has been used for
commercial or rental purposes, has been tampered with, when repairs or attempted repairs have been made by
unauthorized persons, or where the item has been subjected to misuse, abuse, accident or damage in transit. No
charges will be accepted for unauthorized parts, repairs or services.
IN NO EVENT SHALL ALLTRADE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states and provinces do not allow limitations on how long an implied warranty lasts and some states and
provinces do not allow the exclusion or limitation of the incidental or consequential damages, so part or all of the
above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from province to province.
FCC INFORMATION
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Printed in China
FOR CUSTOMER SERVICE
1-800-423-3598
Official Licensed Product.
Vaughan is a registered trademark of
Vaughan & Bushnell Mfg. Co.
All rights reserved.
Distribution & Returns
Reno, NV 89508
www.vaughangear.com
MADE IN CHINA
©2016, Alltrade Tools, LLC
Table of contents
