Vax Vivality V-0071 Product information sheet

V-0071
D - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.
F - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.
GB - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.
I - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.
NL - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.
E - easy guide
Please read carefully before using your V-0071. Always fully extend mains cable before use.

D - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
• Read all instructions carefully, even if you are familiar with the appliance.
• To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
• Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
• Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
• Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
• The use of attachments or accessories sold by other manufacturers is not recommended.
• Do not operate or place any part of this appliance on or near any hot surfaces.
• Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
• This product is intended for internal household use only.
• Do not attempt to repair the appliance yourself.
• Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
• Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
• Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
• Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
• Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
• To clean, wipe the exterior with a damp cloth.
F - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
•Read all instructions carefully, even if you are familiar with the appliance.
•To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
•Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
•Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
•Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
•The use of attachments or accessories sold by other manufacturers is not recommended.
•Do not operate or place any part of this appliance on or near any hot surfaces.
•Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
•This product is intended for internal household use only.
•Do not attempt to repair the appliance yourself.
•Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
•Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
•Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
•Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
•Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
•To clean, wipe the exterior with a damp cloth.
GB - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
•Read all instructions carefully, even if you are familiar with the appliance.
•To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
•Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
•Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
•Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
•The use of attachments or accessories sold by other manufacturers is not recommended.
•Do not operate or place any part of this appliance on or near any hot surfaces.
•Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
•This product is intended for internal household use only.
•Do not attempt to repair the appliance yourself.
•Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
•Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
•Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
•Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
•Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
•To clean, wipe the exterior with a damp cloth.
I - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
•Read all instructions carefully, even if you are familiar with the appliance.
•To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
•Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
•Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
•Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
•The use of attachments or accessories sold by other manufacturers is not recommended.
•Do not operate or place any part of this appliance on or near any hot surfaces.
•Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
•This product is intended for internal household use only.
•Do not attempt to repair the appliance yourself.
•Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
•Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
•Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
•Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
•Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
•To clean, wipe the exterior with a damp cloth.
NL - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
•Read all instructions carefully, even if you are familiar with the appliance.
•To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
•Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
•Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
•Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
•The use of attachments or accessories sold by other manufacturers is not recommended.
•Do not operate or place any part of this appliance on or near any hot surfaces.
•Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
•This product is intended for internal household use only.
•Do not attempt to repair the appliance yourself.
•Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
•Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
•Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
•Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
•Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
•To clean, wipe the exterior with a damp cloth.
E - Save these instructions
Congratulations on the purchase of your V-0071 cylinder cleaner. In order to get the best performance
from this product, please read and retain these instructions. When using electrical appliances, in order to
reduce the risk of fire, electric shock and/or injury to persons, basic safety precautions should be
followed, including the following:
•Read all instructions carefully, even if you are familiar with the appliance.
•To protect against the risk of electric shock, DO NOT IMMERSE the appliance, cordset or plug in water
or other liquid.
•Close supervision is necessary when any appliance is used by or near children. Never leave an appliance
unattended when in use.
•Switch off and remove the plug from the power outlet when not in use and before assembling or
disassembling parts.
•Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or is
dropped/damaged in any manner.
•The use of attachments or accessories sold by other manufacturers is not recommended.
•Do not operate or place any part of this appliance on or near any hot surfaces.
•Do not abuse the cord. Never carry the appliance by the cord or yank it from the power outlet; instead,
grasp the plug and pull to disconnect.
•This product is intended for internal household use only.
•Do not attempt to repair the appliance yourself.
•Do not suck up inflammable liquids such as cleaning fluids, petrol, etc, or their vapours.
•Do not vacuum hard, sharp or over-large objects, matches, hot ashes, cigarette butts or similar materials.
•Do not use the vacuum cleaner without its dust bag or motor protection and air outlet filters.
•Donotusethecleanerifthere is any obstruction in its suction passages, as this may dangerously overheat
the motor.
•Do replace/empty the dust bag and filters after picking up fine dust such as cement, very fine sand, flour etc.
•To clean, wipe the exterior with a damp cloth.
Important information • Important information • Important information
Important information • Important information • Important information
2

21
D - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
GB - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
NL - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
E - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
I - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
F - How to use your V-007
Assembling the appliance
fig. 1 The telescopic extension tubes can be lengthened by pressing the button down and pulling the tubes apart.
fig. 2 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the attachment point on the
vacuum cleaner.
3

34
D - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
F - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
GB - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
I - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
NL - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
E - How to use your V-007
Assembling the easy-reach tool system
Your V-0071 has been equipped with easily accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery brush (B) and crevice tool (C) on the tubes as shown.
A
B
C
4

56
D - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) – The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position – The cleaning head bristles should be raised. Press the rocker switch to lift them.
F - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) –The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position –The cleaning head bristles should be raised. Press the rocker switch to lift them.
GB - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) –The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position –The cleaning head bristles should be raised. Press the rocker switch to lift them.
I - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) –The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position –The cleaning head bristles should be raised. Press the rocker switch to lift them.
NL - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) –The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position –The cleaning head bristles should be raised. Press the rocker switch to lift them.
E - How to use your V-007
Adjusting the cleaning head for carpets & hard floors
fig. 5 Hard floor position (tiles, parquet floors, etc) –The cleaning head bristles must be in the lower position. Press on the rocker
switch to lower them.
fig. 6 Carpet or rug position –The cleaning head bristles should be raised. Press the rocker switch to lift them.
5

7 8 9
D - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
F - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
GB - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
I - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
E - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
NL - How to use your V-007
Fully extend the mains cable and plug it into a standard domestic outlet
fig. 7 Press the foot pedal to start the vacuum cleaner. To stop it, press the pedal again.
fig. 8 Press the foot pedal to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows you to control the suction power.
6

10 11 12
D - How to use your V-007
F - How to use your V-007
GB - How to use your V-007
I - How to use your V-007
NL - How to use your V-007
E - How to use your V-007
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
fig. 10 If you wish to pause briefly during vacuuming i.e. to move a piece of furniture or a rug, use the special parking
position on your vacuum cleaner as shown. Slide the hook attached to the cleaning head into the slot on the rear of the
appliance.
fig. 11&12 You can move or store your appliance in a vertical position by sliding the hook on extension tube into the clip on the
underside of the appliance. This practical system allows you to carry the vacuum cleaner around in one hand and to store
it in the minimum amount of space.
7

13
D - How to care for your V-007
14
GB - How to care for your V-007
F - How to care for your V-007
I - How to care for your V-007
E - How to care for your V-007
NL - How to care for your V-007
14a
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
Your appliance is equipped with a dust bag. If you notice that the vacuum cleaner seems to be less efficient than usual, check the dust
indicator by selecting the maximum power and lifting the vacuum cleaning head off of the floor. If it turns red, empty the dust bag.
To empty the dust bag
fig. 13 Turn off the appliance and unplug it. Lift up the catch to access the dust bag compartment, raise the cover and remove the
bag. Pull the handle up to remove the bag holder.
fig. 14a The clip on the bag can then be removed as shown. fig. 14 Shake the dust bag over a bin so that the dirt can be removed.
Once empty, replace the clip and re-assemble in the cleaner.
8

15 16
D - To change the filters
F - To change the filters
GB - To change the filters
I - To change the filters
NL - To change the filters
E - To change the filters
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set.
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set.
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set.
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set.
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set.
Motor protection filter
fig. 15 The filter is located in the dust bag compartment and protects the motor from dust. To access this filter, remove the grille from the machine and replace it
with a new one. We recommend changing the filter after 5 bag changes or when it appears soiled.
Air outlet filter
fig. 16 The air outlet filter is also housed in the dust bag compartment above and behind the air outlet filter, as shown in fig 16. Remove the dirty filter assembly
from the machine and dispose of the filter medium. Replace with a new filter medium. Return the filter assembly to your V-0071.
We recommend replacing the air outlet filters every 4-6 months, after the bag has been emptied 5 times, when appearance is soiled or a loss of suction is experienced
(whichever is sooner). Attention: Do not use the vacuum cleaner without the full filter set. 9

18
D - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
F - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
GB - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
I - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
NL - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
E - Dust bag indicator
fig. 17 When the indicator turns red or when the suction power reduces substantially, this indicates that you should empty the dust bag.
fig. 18 When the bag is not full, the indicator will show blue.
Attention: If after emptying the dust bag, the indicator stays red, this could be for several reasons: 1, The suction passages may be blocked –check the flexible hose
and extension tubes, suction inlet, floor brushes and nozzles for obstruction. 2, Check the motor protection filter. 3, Check to see if the air outlet filter is dirty.
Check carefully which of these is causing the indicator to light and correct it so that the vacuum cleaner can work normally.
Do not use the vacuum cleaner with the indicator on red, as this could cause irreparable damage to the motor.
17
10

11

D - SERVICE & HELP – VAX CARE 0870 6061248
Mon – Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
F - SERVICE & HELP –VAX CARE 0870 6061248
Mon –Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
GB - SERVICE & HELP –VAX CARE 0870 6061248
Mon –Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
I - SERVICE & HELP –VAX CARE 0870 6061248
Mon –Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
NL - SERVICE & HELP –VAX CARE 0870 6061248
Mon –Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
E - SERVICE & HELP –VAX CARE 0870 6061248
Mon –Fri. 9:00am to 5:00pm. An answer phone is available out of these hours.
If you have queries or concerns about using your VAX, call the HELP LINE.
Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling.
VAX Limited, Kingswood Road, Hampton Lovett, Droitwich, Worcestershire WR9 0QH, UK
Email: [email protected] - Website: www.vax.co.uk
Version 1
12