Vector Technology VT700CR User manual

OPERATION MANUAL
OF FUNCTION SETTING
GSM IC-Card
PAYPHONE
MODEL: VT700CR

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 1 -
Installation:
Getting Starte ：
：：
：Before initial installing the SIM Card to the payphone, please disable your SIM card PIN
code on your cell phone in advance.
If the SIM card requests a PIN CO E to activate, but you do not disable the PIN code in advance, when
the GSM payphone starts initially, LC will display NO PIN CO E. Please enter Function Setting
Mode COMMAN 01: Function 01 to enter your PIN code.
1 ) Insert SIM card ：Open the front door to find the SIM card holder near the door hinge to insert your SIM
card. Clip down the SIM card securely.
2) Please plug in the AC power Adaptor. When the Solar Power supply connection is not established ready
yet, the main power supply is provided from AC power only.
3) Wait for about 30 seconds for network registration process and the LC displays -- GSM POWER ON--
SIM TEST OK – Signal Quality xx –
4) The Payphone LC screen displays “ “W WE EL LC CO OM M” ” in idle mode (on-hook status). Lift up the handset to
display “Welcome” “Insert Card” to make calls.
A) Function Setting Item List of COMMAND (00-31):
The payphone provides 31 Function setting items (COMMAN ) via keypad programming feature. Before setting the
parameters to your phone, please make sure what you want to do, prepare the operational manual by your side and
follow the instructions carefully. If you don’t understand what the function is, don’t change anything, but leave the default
value for safety.
Function Setting Item List of COMMAND (00-31):
Page
Function 00 : Self- iagnosis 4
Function 01 : SIM card pin code setting 5
Function 02 : efine Local/ST /I Area Prefix number (Tariff table prefix number setting) 6
Function 03 : RMS, SIM Card number programming 9
Function 04 : Incoming call time setting 9
Function 05 : RMS, SIM Card number programming 9
Function 06 : Warning Tone 10
Function 07 : SIM card designate setting 10
Function 08 : Total collected money display 10
Function 09 : (Reserved) 11
Function 10 : Meter signal selection 11
Function 11 : Owner password setting 12
Function 12 : (Reserved) 12
Function 13 : Language mode Selecting. 13
Function 14 : The credit of indication of rate Program 15
Function 15 : Time group & Indication of Rate's time program 16
Function 17 : The gateway number setting 17
Function 18 : Speed dial programs (10 sets) 17
Function 19 : Real Time Clock Setting 17
Function 20 : iscount time setting 18
Function 24 : Simple discount program 19
Function 27 : Software checking number. 19
Function 30 : Parameter setting 20
How to set a rate completely 20
Q&A 22
FCT Specification 23

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 2 -
B) How to enter the Function Setting Mo e of COMMAND ( 00-31):
1) Please open the front door and pick up the handset. Slightly ouch the Function door switch (see the photo below).
Funct on/Door sw tch
2) LC will display “COMMAN (00-31)”. If not, please hang up the handset to wait for 5 seconds, and try again.
3) Enter the COMMAN number of the Function Items you want to program and follow the instructions page 4 -22 to
set the parameters.
4) After finishing the programming, LC will return to command screen：
LC isplay
COMMAN (00-31)
5) Press RE AIL key to save the data entered, LC will show SAVING while the data is saving.
LC isplay Operation
1.COMMAN (00-31) Press “RE AIL” to save
2. SAVING Wait for around 10 seconds
Important note:
When the LC shows “ SAVING”, it means the data is saving into the memory chip. Please don’t close the front door or
put the handset back to cradle. Make sure the function switch is open and handset is off hook to avoid any in-completed
data saving process to lead the micro-chip losing memory and causing permanent damage to the phone.
Don’t close the front oor. Make sure the function switch is open.
6) If there is no change of the setting, no update data will be saved. The LC will show EN ING

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 3 -
7) If you touch the function switch carelessly or a power failure happens during the data saving, after the phone regaining
the power, it will be starting to activate. The LC screen will turn from *****GSM****** to xxxxxGSMxxxxxx for 0.5
second. It means the data is not being saved correctly during the previous step. Please re-enter the COMMAN mode
again and complete the data-saving process correctly to save the data by following the correct steps.
C ) FOLLOW ON an REDAIL key efinition for programming purpose:
“FOLLOW ON”
“REDIAL”
a. Press the "FOLLOW ON" key to exit without saving from programming &to return to Command mode.
b. Press the "RE IAL" key to save the programming data and return to Command mode.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 4 -
Funct on 00 : Self-D agnos s
Whe LCD displays COMMAND (00 –31), please e ter 00 to start Fu ctio 00: "Self-Diag osis"
Diag ostic items: KEYBOARD u it
Fu ctio a d door SWITCH
HOOK SWTICH u it
HANDSET u it
LCD DISPLAY u it
Operatio LCD Display
SELECT (0-1)
Select "0" to ru step 1 KEYPAD TEST
(0) 0000000000000000
(1) 1111111111111111
(2) 2222222222222222
(3) 3333333333333333
(4) 4444444444444444
(5) 5555555555555555
(6) 6666666666666666
(7) 7777777777777777
(8) 8888888888888888
(9) 9999999999999999
(*) ****************
(#) ################
(FOLLOW ON) NNNNNNNNNNNNNNN
(REDIAL) RRRRRRRRRRRRRRRR
(LOUD) LLLLLLLLLLLLLLLLL
Door a d fu ctio switch ope CASHBOX OUT
Door a d fu ctio switch close CASHBOX IN

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 5 -
Funct on 01: SIM card PIN code program
Note: this function is only necessary when you do not disable the PIN code on your cell phone in advance.
Whe LCD displays COMMAND (00 –31), please e ter 01 to start Fu ctio 01: SIM card PIN
code program
Operatio LCD Display
COMMAND(00-30)
Press "01" OWNER PASS:
Key the PIN code OWNER PASS: ****
Press" REDIAL" to save

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 6 -
Funct on 02: Def ne Local/STD/IDD Area Pref x number
(Tar ff table pref x number sett ng)
Note: This fu ctio 02 helps you defi e the Local/STD/IDD CALL AREA Telepho e Prefix
Numbers. We defi e 3 Call Areas below:
0 : Local CALL AREA : The Prefix umber is 1, 2,3,4,5,6,7,8 or 9. (1 digit)
1: STD CALL AREA : The Prefix umber is 0. ( 1 digit)
2: IDD CALL AREA : The Prefix umber is 00. ( 2 digits)
Example:
If you would like to program the prefix umber 00886XXXX…. is 1 dollar for 60 seco ds.
You eed to program 00886 i the IDD Call Area. Because 00886 prefix with 00, the default of
IDD Call Area prefix umber is 00.
The , we eed to program the rate. The rate is 1 dollar for 60 seco d will be program i Fu ctio
14 a d Fu ctio 15.
I Fu ctio 02, we o ly program the i dicatio of Rate. There are 47 sets i dicatio of Rate.
Now, we choose the Rate 07 which is 1 dollar for 60 seco ds. (Please check the Fu ctio 14 a d
Fu ctio 15 later)
LCD D splay Operat on
1) COMMAND (00-31) press 02
2) FUN PASS: **** 8080( e ter 8080 password)
3) CALL AREA (0/2): press 2 (0 for LOCAL,1 for STD,2 for IDD Call
Area)
4) IDD 000-399: press 000(The Serial No.000-399 total is 400sets
for IDD Call Area )
5) 000: e ter 00886 a d press REDAIL key (00886 is
the Prefix Code ; press REDAIL to save )
6) 000:00886 07 e ter 07 a d REDAIL key ( 07 is the i dicatio
of Rate , press REDAIL to save)
7) CALL AREA (0/2):
Notes: 1) Funct on Password: It ca be cha ged i fu ctio 23.
2) Ind cat on of Rate :

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 7 -
There are 47 sets i dicatio of Rate. After we call the i dicatio 7 is Rate”07”.
Whe we program the 00886 prefix umber will follow the Rate”07”. All the pho e
umber will follow the tariff with Rate”07”.
How do you defi e the Rate”07” to follow 1 dollar for 60 seco ds? Please check the
fu ctio 14 a d fu ctio 15 later.
3) The default for nd cat on of rate :
Rate"00" is default rate of LOCAL Call Area.
( The prefix umber 1, 2, 3, 4, 5, 6, 7, 8 or 9 which does ’t program i the LOCAL Call
Area will follow the Rate”00”)
Rate"01" is default rate of STD Call Area.
( The prefix umber 0 which does ’t program i the STD Call Area will follow the
Rate”01”)
Rate"02" is default rate of IDD Call Area.
( The prefix umber 00 which does ’t program i the LOCAL Call Area will follow the
Rate”02”)
Rate"46" is default rate of FREE CALL.
Rate"47" is default rate of BARRED CALL.
4) Ser al No. of Call Area :
Local Call Area: 000-199 , total 200 sets.
STD Call Area : 000-399, total 400 sets.
IDD Call Area : 000-399, total 400 sets.
5) Pr or ty :
For the CALL AREA : The priority is IDD , STD, the LOCAL CALL AREA.
For the Ser al no of Call Area :
High Serial o. will be prior tha low serial o.
Example:
We program the 00886 prefix umber i the IDD CALL AREA a d i the Serial No.
000.
LCD D splay Operat on
8) COMMAND (00-31) 02
9) FUN PASS: **** 8080( I put password)
10) CALL AREA (0/2): 2 (0 for LOCAL,1 for STD,2 for IDD Call Area)
11) IDD 000-399: 000(The Serial No.000-
399 total is 400sets for

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 8 -
IDD Call Area )
12) 000: press 00886 a d REDAIL key (00886 is the
Prefix Code ; REDAIL to save )
13) 000:00886 07 07 a d REDAIL key( 07 is the i dicatio of
Rate , REDAIL to save )
Next, we co ti ue to program the 008867 prefix umber i the IDD CALL AREA a d
the Serial No. 001
14) CALL AREA (0/2): 2 (0 for LOCAL,1 for STD,2 for IDD Call Area)
15) IDD 000-399: 001(The Serial No. 000-
399 total is 400sets for
IDD Call Area )
16) 001: 008867 a d REDAIL key (008867 is the Prefix
Code ; REDAIL key to save)
17) 001:008867 08 08 a d REDAIL ( 08 is the i dicatio of Rate ,
REDAIL to save)
18) CALL AREA (0/2):
After fi ishi g the program, whe we dial 008867XXX, the tariff will follow Rate”08”.
If you program the 00886 i Serial No. 001 a d the 008867 i Serial No. 000.
Whe we dial 008867XXXX, the tariff will follow the Rate”07”.
Si ce the CHIP system program check is starti g from Serial No. 399 to 000, the priority
001 prevails over 000.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 9 -
Funct on 03: RMS, SMS caller ID
The Fu ctio is to save the RMS of SMS Caller ID to the paypho e.
Please see the RMS ma ual for the operatio .
Funct on 04: Incom ng call
To program the time limited of the i comi g call
Example: If you wa t to set the time of i comi g call for 10 mi utes.
Operatio LCD Display
COMMAND(00-30)
Press "04" INCOMING: 0M
Press "1" to i crease to 10 INCOMING: 10M
Note:
Press "1" o e time will decrease 1 mi ute, "3" will i crease 1 mi ute.
The Mi is 0 M. The Max is 100 M.
Funct on 05: RMS, the SIM card number programm ng
To use the RMS function, please make sure that RMS function is available for your
payphone. CPU an Flash Memory chip shoul be upgra e .
Step 1 Exchange RMS cell phone's SIM car with payphone's SIM car
Step 2 Set RMS cell phone's numbers un er function 05, then it'll return to
comman mo e
Step 3 Enter function 03, you'll see the screen showing" SAVE" an payphone will
sen SMS to itself. When you hear "Di Di", it means SMS is successful. Payphone
will return to comman mo e again
Step 4 Be sure to press "REDIAL" key to save the ata.
Step 5 Exchange SIM CARDS BACK.
Please rea the
G
GG
GSM
SM SM
SM RMS
RMS RMS
RMS Operation Manual
Operation Manual Operation Manual
Operation Manual for etails.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 10 -
Funct on 06: Warn ng Tone Sett ng
To program whe the War i g To e appears before disco ectio .
Example: If you wa t to set the war i g to e appear i 10 seco ds before disco ectio .
Operatio LCD Display
COMMAND(00-30)
Press "06" WT: 0S
Press "4" to i crease to 10 WT: 10S
Note:
1) Press "1" o e time will decrease 0.1 sec., "3" will i crease 0.1 sec.
2) Press "4" o e time will decrease 1 sec., "6" will i crease 1 sec.
Funct on 07: The SIM card lock sett ng
You ca program a specific SIM card i this fu ctio . The paypho e will be worki g with the SIM
card o ly you program.
Example: To e able this fu ctio . Please i sert the SIM card you prefer to lock before pluggi g
the power.
Operatio LCD Display
COMMAND(00-30)
Press "07" SIM.PRESET :0/1 0
Press "1" to E able ENABLE
Press "Redial" to save
If you wa t to disable it, please Press "0'.
Funct on 08: Total Collected Money D splay
Display o ly.
SUM is total collected mo ey from this paypho e i stalled. PURSE is the bala ce from crediti g
air time values.
Note: if you wa t to clear the bala ce here, please refer to fu ctio 30.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 11 -
Funct on 09: (Reserved)
Funct on 10: Meter ng S gnal Select ng
There are two meteri g Sig al Selectio s (0) Auto detectio , (1) Auto + C. Normally, please set
(0) Autodetect on as default. (1) Auto+ C is special fu ctio to cooperate with gateway termi al
a d ow er should also set gateway umbers u der Fu ctio 17
Set the pho e to tariff o the GSM system via auto detectio .
Operatio LCD Display
COMMAND(00-30)
Press "10" METER(0-1)
Press "0" select auto detectio AUTODETECTION
Note: If you select "1" for Gateway system, please program the fu ctio 17 also.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 12 -
Funct on 11: Owner password sett ng
To set the password for the free call. 1 to 10 digits.
Operatio LCD Display
COMMAND(00-30)
Press "11" OWNER PASS :
Please key i the password "1234567" 1234567
You ca set for max 10 digital.
a d press "redial" to save
How to use: Pick up the ha dset. Press the "louder" key, the LCD will ask the pass word.
Key i the ow er password a d press the "Redial" It ca make a free call.
Funct on 12: (Reversed)

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 13 -
Funct on 13: Language Mode Select ng
There are two la guage modes you ca choose. 0 is for E glish, 1 a d 2 are for other la guages.
Example: if you wa t to select the seco d mode.
Operatio LCD Display
COMMAND(00-30)
Press "13" ENG / OTHER (0/2):
Press "1" to select local la guage
Press "Redial" to save
Note:
You ca press the" follow o " butto to cha ge the la guage display before diali g the telepho e
umber.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 14 -
Funct on 14: The cred t of nd cat on of rate Program
This fu ctio is to program the credit of the nd cat on of rate.
If you choose the tariff by paypho e ( I fu ctio 10 you choose tariff by paypho e itself),
you eed to program the credit of the i dicatio of rate.
There are 47 sets i dicatio of rate for programmi g. But the Rate”46” a d Rate “47” is fix.
Rate”46” 

 Free call
Rate “47”

 Barred call
Example:
I the fu ctio 02, we program the prefix umber 00886 will follow the Rate”07”. Now, we
program the credit of the Rate “07” i fu ctio 14. The credit is 1 dollar for 60 seco ds. We
program 1 dollar i fu ctio 14.
LCD D splay Operat on
1. COMMAND(00-31) 14
2. TAXE(1) press 1 a d REDAIL key( This is for system tariff ,
please read below)
3. TAXE(2) press 1 a d REDAIL key ( This is for system tariff ,
please read below)
4. RATE(00-47): 07 a d REDAIL key (Program the Rate”07”
5. MIN.1 ST 1 ( 1 dolla
r for the mi imum credit the user should
i sert to make a call)
6. MIN 2 ND: 2 ( Whe the MIN.1 ST credit ru out, User should
i sert 2 dollar to keep this call co ti ue.)
7. RATE(00-47): You ca co ti ue to program other nd cat on of rate.
Note. 1) I fu ctio 10, you choose :
. (4) REVERSE＋_SELF (5) 50Hz_＋_SELF
(6) 16KHz_＋_SELF (7) 12KHz_＋_SELF
(8) AUTODECT
It will tariff by paypho e.
2) The TAXE(1) , TAXE(2) , is for the system Tariff. Please program the mi imum credit i
TAXE(1) , TAXE(2), whe you choose the tariff by paypho e itself.
If you choose the tariff by system ( I fu ctio 10 you choose tariff by system), you eed to
program the credit of TAXE(1) a d TAXE(2).

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 15 -
Example : The tariff is by System. Each meteri g sig al will take 1 dollar credit.
LCD D splay Operat on
1. COMMAND(00-31) 14
2. TAXE(1) 1 a d REDAIL key(The first meteri g sig al from
system, the paypho e will take 1 dollar credit. )
3. TAXE(2) 1 a d REDAIL key ( The seco d a d after meteri g
sig al from system, the paypho e will take 1 dollar credit)
4. RATE(00-47): 07 a d REDAL key ( If you would like to the prefix
umber 00886 will be asked for 1 dollar mi imum i sert, you ca program the i dicatio of
rate or you may ig ore it.)
5. MIN.1 ST
1 ( 1 dollar for the mi imum credit the user should
i sert to make a call)
6. MIN 2 ND: 2 ( Whe the credit is less tha Taxe(2), User should
i sert 2 dollar to keep this call co ti ue. Or the
paypho e will disco ect this call whe it receive
the ext meteri g sig al )
Note. 1) I fu ctio 10, you choose :
. (0) REVERSE (1) METERING_50Hz
(2) METERING_16KHz (3) METERING_12KHz
It will tariff by system.
2) I the example, if you program the prefix umber 00886 i Fu ctio 02, a d the MIN.1
ST a d MIN 2 ND i fu ctio 14. Whe user dial the 00886XXX umbers, the paypho e
will ask for the mi imum credit 1 dollar to make a call a d 2 dollar for keepi g this call
co ti ue.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 16 -
Funct on 15: T me group & Ind cat on of Rate's t me program
This fu ctio is to program the time of the nd cat on of rate.
If you choose the tariff by paypho e itself (I fu ctio 10 you choose tariff by paypho e
itself), you eed to program the Time of the i dicatio of rate.
There are 47 sets i dicatio of rate for programmi g. But the Rate”46” a d Rate “47” is
fixed.
Rate”46” 

 Free call
Rate “47”

 Barred call
Thus, there are Rate 00-45 ca be programmed.
TIME GROUP (FOR D scount t me program, please check the funct on 20 later):
The Time Group has 18 sets, Group (00-17), for discou t programmi g. Normal rate ( o
discou t) is group 00. I this fu ctio , You ca set the commu icatio time (seco ds) for each
rate at differe t discou t time. (Discou t time is defi ed i fu ctio 20).
Example:
Follow fu ctio 02 a d 14 example, we wa t to program the prefix umber 00886 is 1 dollar for
60 seco ds.
LCD D splay Operat on
1. COMMAND(00-31) 15
2. GROUP(00-17) 00 (Set for ormal time first , please read the otes
below )
3. RATE(00-45) 07
4. RATE: 60 S 60 S
5. RATE(00-45) You may program other i dicatio of Rate.
Notes:
1) There are 18 sets time groups. There is Rate”00-47” i each time groups. Thus, i
differe t time will follow the differe t tariff rate. How to program the time zo e? Please
check the Fu ctio 20. Please check the Fu ctio 20.

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 17 -
.
Funct on 17: Gateway number sett ng
You ca program the gateway umbers i this fu ctio .
Funct on 18: Speed d al programs
User ca press “MEMO fu ctio key” +“0(1/2/3/4/5/6/7/8/9)” for a speed dial call. Due to
less choice i hot li e fu ctio , this fu ctio ca compe sate ow er to set ma y hot li e pho e
umbers.
Example:
If you wa t to set speed dial umber “MEMO 0”=”22678080”. The rest ca be do e i the same
ma er. “MEMO 1”=“12345678”, “MEMO 2”=“87654321”, etc.
Operatio LCD Display
COMMAND(00-30)
Press “18” SPEEDDIAL(0-9)
Press “0” SPEEDDIAL(0-9)
“22678080” “Redial”
Funct on 19: Real T me clock Sett ng
Example: Set the 2003/3/28 09:50:45 Wed esday
Operatio LCD Display
COMMAND(00-30)
Press "19" REAL TIME CLOCK INPUT
KEY IN YEAR YEAR :2003
KEY IN MONTH MONTH:03
KEY IN DAY DAY: 28
KEY IN HOUR HOUR: 09
KEY IN MIN MINUT: 50
KEY IN SEC SECOND: 45
KEY IN WEEK WEEKDAY:3

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 18 -
Funct on 20: D scount t me Sett ng
You ca defi e what time i terval is for discou t rate which set u der fu ctio 15.
Example:
Follow fu ctio 15’s example. We should defi e the time i terval for discou t rate. The time we
set is period 00, everyday, AM00:00~06:00, group 01
Operatio LCD Display
COMMAND(00-30)
Press "20" PERIOD(00-17)
Press "00" to select the first period CLOCK INPUT
The total periods are 18 sets (00-17)
Key "0230060000060001" 0230060000060001
Press "Redial" to save
Note:
1) Pho e must have real time clock(RTC) hardware support.
2) Format:
02 30 0 6 00 00 06 00 01
mo th day week week hour mi . hour mi group
start e d start start e d e d
3) Mo th: 2 digits, ra gi g form 01 to 12, if key i 00 mea s a y mo th
Day: 2 digits, ra gi g from 01 to 31 & 00 mea s a y day
Weekday: 1 digit, ra gi g from 0 (Su day) to 6 (Saturday)
Hour: 2 digits, ra gi g from 00 to 23.
Mi ute: 2 digits, ra gi g from 00 to 59
Time group: 2 digits, ra gi g from 0 to 23
4) If hour setti g across to a other day must be divided i to two time periods ex. 9:00pm to
6:00am You should set first period 9:00pm to 11:59pm, seco d period 00:00am to 6:00am.
Group 00 is ormal rate, o discou t.
Time group correspo ds to Fu ctio 15

Vector Technology Co. – GSM IC-CARD Payphone Manual
GSM IC-Card PAYPHONE - 19 -
Funct on 24: S mple d scount program
Our fu ctio 24 is to set all rates i crease/decrease perce tage o matter ormal or discou t time
Example: Adjust the rate to 200% (double)
Operatio LCD Display
COMMAND(00-30)
Press "24" DISCOUNT: 100%
Press "3" to i crease to 200% DISCOUNT: 200%
Press "Redial" to save
The Call Time Discou t Discou ted time
180S 50% 90S
180S 120% 216S
180S 200% 360S
Note1): Press “1” to decrease, “3” to i crease
2): The discou t ra ge: from 0%~200%
Funct on 27: Software Vers on NB.
Show the software check sum.
Operatio LCD Display
COMMAND(00-30)
Press "27" AA08
"AA08" is the software's check sum.