Velleman High-Q Velleman-Kit K8057 User manual

K8057
ILLUSTRATED ASSEMBLY MANUAL H8057IP-1
Total solder points: 91
Difficulty level: beginner 1 2 3  4 5 advanced
ForusewithK8059/VM108
2ChannelRFtransmitter
2 CHANNEL RF RECEIVER
Specifications
 Power supply : 9 to 12V AC or DC / 100mA max.
 Relay contacts NO / NC: 3A each.
 Selectable timers per output
 Open field range of up to 30m possible.
 On board antenna or external antenna.
 Dimensions : 100 x 82mm.

2
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
• Thin raisin-core solder. Do not use any flux or grease.
• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
⇒Make sure the skill level matches your experience, to avoid disappointments.
⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.
⇒Perform the assembly in the correct order as stated in this manual
⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒Values on the circuit diagram are subject to changes.
⇒Values in this assembly guide are correct*
⇒Use the check-boxes to mark your progress.
⇒Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0
.0
0
0

3
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE
CORRECT MOUNTING SEQUENCE !

4
Construction / Bouw / Montage / Montaje
 D1 : 1N4148
 D2 : 1N4148
 D3 : 1N4007
 D4 : 1N4007
 D5 : 1N4007
 D6 : 1N4007
Watch the polarity! - Let op de polariteit!
Attention à la polarité! - Achten Sie auf
die Polarität! - ¡Controle la polaridad!
1. Diodes / Diode / Diodo
D...
CATHODE
 R1 : 330 (3 - 3 - 1 - B)
 R2 : 330 (3 - 3 - 1 - B)
 R3 : 330 (3 - 3 - 1 - B)
 R4 : 330 (3 - 3 - 1 - B)
 R5 : 47K (4 - 7 - 3 - B)
 R6 : 47K (4 - 7 - 3 - B)
2. Resistors / Weerstanden /
Résistances / Widerstände /
Resistencias
R...
 IC1 : 8p
Pay attention of the notch!
Let op de positie van de nok!
Attention à la position de l’encoche!
Achten Sie auf des position des Nockens!
¡Atención a la posición del la muesca!
3. IC socket / IC voetje / support
de CI / IC-Fassung / Zócalo de
integrado
 C1 : 100nF (104)
 C2 : 100nF (104)
4. Capacitors / Kondensatoren /
Condensateurs / Kondensa-
toren / Condensadores
 VR1 : UA78L05
6. Voltage regulator / Spannings-
regelaar / Régulateur de tension /
Spannungsregler / Regulador de
tensión
VR...
 T1 : BC547B
 T2 : BC547B
5. Transistor
 SW1 :KRS0610
7. Push button / Drukknop /
bouton-poussoir /
Druckknöpfe / Pulsador
SW...
 SK1
8. DC-jack / DC connector /
Connecteur CC / DC -
Einbaubuchse / Conector CC
-
SK... +
SW

5
 SK2 : 2p.
 SK3 : 3p.
 SK4 : 3p.
10. Screw terminal / schroef-
connectoren / connecteurs à
visser / Schraubconnectoren /
Regletas de conexión
Construction / Bouw / Montage / Montaje
 C4 : 100µF

C5 : 10µF
Watch the polarity!
Let op de polariteit!
Attention à la polarité!
Achten Sie auf die Polarität!
¡Controle la polaridad!
11. Electrolytic Capacitors /
Electrolytische condensatoren /
Condensateurs électrolytiques /
Elektrolytkondensatoren / Con-
densadores electrolíticos
C...
 RY1 : V3SM121C (12VDC - 3A - 1 c)
 RY2 : V3SM121C (12VDC - 3A - 1 c)
12. Relays / Relais / Relés
R Y...
 LD1 : 3mm RED
 LD2 : 3mm RED
 LD3 : 3mm RED
 LD4 : 3mm RED
Watch the polarity!
Let op de polariteit!
Attention à la polarité!
Achten Sie auf die Polarität!
¡Controle la polaridad!
13. LEDs
COLOR= 2...5
LD...
CATHODE
16mm
 RX1 : 433MHz.
9. Receiver module / Ontvangst-
module / Module récepteur /
Empfängermodul / Módulo de
recepción
!
 IC1 : VK8057
VK8057=(Programmed PIC12F629)
Pay attention of the notch!
Let op de positie van de nok!
Attention à la position de l’encoche!
Achten Sie auf des position des Nockens!
¡Atención a la posición del la muesca!
14. IC / CI

6
Construction / Bouw / Montage / Montaje
16. PCB / Print layout / Circuit imprimé / Leiterplatten-Lay-out /
Circuit integrado
Solder a 30cm / 0.5mm² wire (option) for an
improved reception quality.
Soldeer een draad van 30cm / 0.5mm² (optie)
voor een betere ontvangst.
Soudez un fil de 30cm / 0.5mm² (option) pour
une meilleure réception.
Löten Sie einen Draht von 30cm/0.5mm²
(optional) wenn Sie einen besseren Empfang
wünschen.
Suelde un hilo de 30cm / 0,5mm² (opción) si
quiere una mejor recepción
15. Antenna / Antenne / Antena
Solder

7
17. Schematic diagram / Schema / Schematisches diagram / Diagrama esquemática
Schematic diagram

5 410329 311865
Modifications and typographical errors reserved - © Velleman nv. H8057IP - 2004 - ED1