VENETA 37103-64500-B Instruction sheet

Required Tools measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
How to install your
#37103-64500-B
Shutters with Reveal Frame
Difficulty:
Included Hardware
The hardware can be found in
the small hardware box included
with your blind.
1
1Getting Started
2Assemble the Frame
1
Make sure ITEM# (Highlighted in the circle) matches on both panel boxes.
Do not dispose of packaging until the shutters are operating appropriately.
Use of a moving blanket or drop cloth is recommended.
Find ample working space to assemble your frame (preferably in front of the window).
Check the diagram to make sure you have all the parts indicated for an appropriate
installation.
Carefully remove panels and frames
from the packaging.
Do not mix panels or frames from other
windows. All frame pieces are labeled
(top, bottom, right, left).
Dovetail Key
Hinge
Pins
Short
Screws
(For Hinge
Installation)
Plug
Hinge Spacer
Long
Screws
(For Frame
Installation)
The top and bottom of the T-post are labeled. Locate and identify. Line up the pre-drilled
holes with the top and bottom frame and secure with screws provided. Fasten the T-post
with additional nails if necessary.
※If not installing with T-POST, skip to #4.
The T-post connector provides
some wiggle room, make sure the
T-post is at the center position at
each end and secure with two
screws.The T-post can also be
adjusted when gaps between
panels are not even.
Set all frames on a soft, level surface (moving blankets or some type of pad works best).
Position each side of the frame and line up the Dovetail Key slot.
1
2
3
Medium
Screws
(For T-post
Installation)
Shutters with Reveal Frame
How to install your
#37103-64500-B
Difficulty:
2
The frame is pre-drilled well in the top left and right frame, bottom
left and right frame, and in the middle of the top and bottom
frame. Double check that all the holes are pre-drilled before
placing the frame on the window.
4
Position the assembled frame evenly along the window opening against the window. by using a tape measure and shims.
5
Once you have evenly spaced the frame into the window
opening, secure with a screw (pre-drill) into the upper left frame
ONLY. Shutter will be fully secured in later steps.
Once done, level the frame on the window.
6
Measure left & top frame for spacing Measure right & top frame for spacing
Only secure one screw into the top left frame.
Once the left side is secured, to keep the frame level and secure with a screw (pre-drill) into upper right frame. Shutter will be
fully secured in later steps.
7
8
Level the top frame. Only secure one screw into the top right frame.
With the rounded side of the Dovetail Key facing up,
push the top frame down onto the Dovetail Key.
The Dovetail Key has a rounded side and a flat side.
The rounded side should be inserted in slot first.
!
Insert the Dovetail Key into each slot at the back of the frame. Use a rubber mallet if necessary.
1 2 3 4

How to install your
#37103-64500-B
Shutters with Reveal Frame
Difficulty:
3
Shutters with Reveal Frame
How to install and maintain your
#37103-64500-B
Difficulty:
4
With the top right and left frame secured, place the left shutter panel in the frame and slide into position. Align the hinges, and insert
the hinge pin.
Open the left panel and place the right
shutter panel(s) in the frame, slide into
position, insert hinge pins into hinges.
Note: If you have bi-fold panels, after
attaching the far left and/or far right panels
to the frame, you will need to join the hinges
of the panels labeled P1 and P2 and insert
hinge pins. Repeat for panels labeled P3
and P4 if you have these. Proper order of
panels from left to right is P1, P2, P3, P4.
9
If panel hinges are not aligned with frame
hinges properly, then frame hinges can be
adjusted.
10
Once panels have been positioned
and secured with the hinge pins,
make sure shutter panels are even
across the top and bottom. If panels
are not even, shift (rack) your frame
left to right until the gap is even.
11
Position left panel in the frame. Slide panel into frame hinges.
Position right panel in the frame. Slide panel into frame hinges and
close other panel to hold in place.
Once you have installed the
panels, but they do not line up.
After racking of shutter,
panels should line up.
RACK the bottom of your
frame to the left or
right for an even reveal.
Check gaps between panels and adjust accordingly with hinge spacers provided if needed.
15
Once the panels are lined up, screw at the bottom of the
left frame.
Only secure one screw into the bottom left frame. Only secure one screw into the bottom right frame.
12
13 After securing the bottom left, secure with a screw at the
bottom right.
14
DOUBLE CHECK AND MAKE SURE PANELS ARE STILL EVEN
ACROSS THE TOP...
Step away from the window and open louvers to
make sure shutter is evenly positioned to window.
Tip:
Loosen screws. Spacer Installed.Insert spacer behind hinge.
tighten screws.
Open and close panels to make sure panels operate properly. Secure the frame with
screws through the rest of the holes.
16
Move top & bottom frame up and down to achieve proper tolerance between
panel and frame.
Tip:
Move side frames in and out to achieve proper tolerance between panel and
frame.
Tip:
After the top and bottom frame are secured, check that
the shutter operates properly. Fasten the deadlock screw
for all hinges.
17 Install the plugs into the frames’ pre-drilled plug holes to
complete the look of your shutters.
18
It is recommended to apply 2 screws for every
hinge, and 1 screw between hinges.
Tip:
3Assemble Panels
Great Job… Enjoy your new Veneta Shutters!
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
Cleaning
Use a clean, dry feather duster, cloth or vacuum with brush attachment to gently remove
dust and debris.To ensure thorough cleaning, wipe the louvers or slats in the open and
closed positions. Do not immerse the product in water or use abrasive chemical solvents.
This may cause discoloration and the louvers to warp. Ultrasonic cleaning is not
recommended. For best results on TecWood Shutters use a cotton cloth dampened with
water. Polyester cloths tend to create static, which can attract dust.
Need HELP?
Call our
Customer Service team
for assistance
1300 836 382
Maintaining your
Blind
1
Loosen frame hinge screws, adjust frame hinges
properly,tighten screws.