VENETA 37103-64600-B Instruction sheet

Required Tools measuring
tape
drill with
2mm bit
phillips bit or
screwdriver
pencil knife
How to install your
#37103-64600-B
Shutters with Face Fit Frame
Difficulty:
Included Hardware
The hardware can be found in
the small hardware box included
with your blind.
1
1Getting Started
1
Make sure ITEM# (Highlighted in the circle) matches on both panel boxes.
Do not dispose of packaging until the shutters are operating appropriately.
Use of a moving blanket or drop cloth is recommended.
Find ample working space to assemble your frame (preferably in front of the window).
Check the diagram to make sure you have all the parts indicated for an appropriate
installation.
Carefully remove panels and frames from the
packaging. Do not mix panels or frames from
other windows. All frame parts are labeled
(top,bottom, right, left).
Dovetail Key
Hinge
Pins
Short
Screws
(For Hinge
Installation)
Long
Screws
(For Frame
Installation)
Medium
Screws
(For T-post
Installation)
1
Remove inserts. All frame parts will be labeled
(top, bottom, right, left).
2
Remove inserts and place them away from
the installation area. Do not mix inserts with
other windows.
Tip:
Hinge Spacer
2Assemble the Frame
Once top right & left frame are secured, panels can be installed...
How to install your
#37103-64600-B
Shutters with Face Fit Frame
Difficulty:
2
Position the assembled frame evenly around the window opening & secure with a screw into the upper left frame ONLY. Shutter
will be fully secured in later steps.Once done, level the frame on the window.
6
5
Once the left side is secured, to keep the frame level and secure with a screw into the upper right frame. Shutter will be fully
secured in later steps.
7
Place the left shutter panel(s) in the frame, slide into position, align the hinges, insert hinge pins into hinges.
8
Place the right shutter panel(s) in the frame, and insert hinge
pins into hinges.
Note: If you have bi-fold panels, after attaching the far left
and/or far right panels to the frame, you will need to join the
hinges of the panels labeled P1 and P2 and insert hinge pins.
Repeat for panels labeled P3 and P4 if you have these. Proper
order of panels from left to right is P1, P2, P3, P4.
9
Frame only Frame with T-post
3Assemble Panels
The T-post connector provides
some wiggle room, make sure the
T-post is at the center position at
each end and secure with two
screws.The T-post can also be
adjusted when gaps between
panels are not even.
Set all frames on a soft, level surface (moving blankets or some type of pad works best).
Position each side of the frame and line up the Dovetail Key slot.
3
The top and bottom of the T-post are labeled. Locate and identify. Line up the pre-drilled
holes with the top and bottom frame and secure with screws provided. Fasten the T-post
with additional nails if necessary.
※If not installing with T-POST, skip to #5.
4
Insert the Dovetail Key into each slot at the back of the frame. Use a rubber mallet if necessary.
Repeat step ⑤for remaining corners to complete the 4-sided frame assembly.
The Dovetail Key has a rounded side and a flat side.
The rounded side should be inserted in slot first.
With the rounded side of the Dovetail Key facing up,
push the top frame down onto the Dovetail Key.
!
1 2 3 4

3
If panel hinges are not aligned with frame hinges properly, then frame hinges can be adjusted.
10
How to install your
#37103-64600-B
Shutters with Face Fit Frame
Difficulty:
3
Once panels have been positioned and secured with the hinge pins, make sure shutter panels are even across the top and
bottom. If panels are not even, shift (rack) your frame left to right until the gap is even.
11
Check gap between panels and adjust accordingly with hinge spacers provided if needed.
13
Open and close panels to make sure panels operate properly. Secure the frame with screws through the rest of the holes.
Make sure gap between the panel and the frame are even.
14
Fasten the deadlock screw for all hinges.
15
Once panels line up, secure a screw at the bottom of the left frame and right frame.
12
Remember: bottom frame should not be secured at this point.
Step away from the window and open louvers to ensure the shutter is evenly positioned on the window.
Tip:
Move top & bottom frame up and down to achieve proper tolerance between panel and frame.
Tip:
Move side frames in and out to achieve proper tolerance between panel and frame.
Tip:
(DOUBLE CHECK AND MAKE SURE PANELS ARE STILL EVEN ACROSS THE TOP)...
Loosen Screws Insert spacer behind
hinge, tighten screws
Spacer Installed
How to install and maintain your
#37103-64600-B
Shutters with Face Fit Frame
Difficulty:
4
Please write a review on our
website at…
www.venetablinds.com.au
Feedback?
We would love to know how you
went with your installation…
Need HELP?
Call our
Customer Service team
for assistance
1300 836 382
Maintaining your
Blind
16
1Cleaning
Use a clean, dry feather duster, cloth or vacuum with brush attachment to gently remove
dust and debris.To ensure thorough cleaning, wipe the louvers or slats in the open and
closed positions. Do not immerse the product in water or use abrasive chemical solvents.
This may cause discoloration and the louvers to warp. Ultrasonic cleaning is not
recommended. For best results on TecWood Shutters use a cotton cloth dampened with
water. Polyester cloths tend to create static, which can attract dust.
Great Job… Enjoy your new Veneta Shutters!
Loosen frame hinge
screws, adjust frame
hinges properly,tighten
screws.
IMPORTANT: Check shutter operation and alignment before installing frame inserts, as frame inserts can NOT be removed once they
are snapped into place.
Match each frame insert with the corresponding side of the frame: Left to Left,Top to Top, Right to Right, Bottom to Bottom.
Snap the frame inserts into place (OR remove double-sided foam tape and put the frame insert into place).This will cover screws and
provide a finished look.
A rubber mallet can be used to help install frame inserts.
!
Double-sided foam tape for wood frame only:
Remove double-sided foam tape and put the
frame insert into place.