Vent-Axia sentinel Kinetic MVHR series User manual

Copyright © 2009 Vent-Axia Limited. All rights reserved.
Sentinel
Kinetic MVHR Range
Installation of the unit in the Opposite
Orientation (LH Condensate)
Stock Ref. N°
438222 Kinetic B Right
443319 Kinetic BH Right
408167 Kinetic FH Right
443028 Kinetic Plus B Right
408449 Kinetic High Flow Right
Read in conjunction with Sentinel Kinetic MVHR Installation &
Commissioning

Sentinel Kinetic MVHR Installation & Commissioning 2
If the orientation of the condensate exit (and the atmosphere spigots) would be better suited on the left of the
unit, the front Control Unit and the rear Cable Inlet Plate can be swapped over to allow the unit to be installed in
the opposite orientation.
Installing the Unit in the Opposite Orientation (LH Condensate)
Installing the unit in the opposite
orientation involves removing the front
cover (and associated Control Unit
Panel), and the rear cover (and
associated Cable Inlet Plate), rotating
the unit chassis and covers through 180
degrees and then re-attaching them.
This moves the condensate drain exit
from the right (rear) corner of the unit to
the left (front) corner of the unit, when
viewed from the front (viewing the
Control Unit).
Figure 1: Installing the Unit in the Opposite Orientation
Remove the front and rear covers by
unscrewing the) fixing screws on both
covers (see Figure1).
Six screws for the Kinetic.
Eight screws for the Kinetic Plus
Remove the 2 screws and detach
the Electrical Cover from the front of the
unit (see Figure 2).
Figure 2: Detaching the Electrical Cover (Front of Unit)

Remove the 2 screws and detach
the Control Panel and disconnect the
mains lead.
(see Figure 3).
Figure 3: Detaching the Control Panel (Front of Unit)
Disconnect the ribbon cable (see
Figure 4).
Figure 4: Disconnecting the Ribbon cable (Front of Unit)
Disconnect the 4-way connector
(see Figure 5).
Figure 5: Disconnecting the 4-way connector (Front of Unit)
Remove the 2 screws and detach
the rear Cable Inlet Plate (see Figure
6).
Figure 6: Removing the Cable Inlet Plate (Rear of Unit)
Re-attach the Cable Inlet Plate on the opposite side of the unit.

Fit the Control Panel on the opposite side of the unit. Taking care to reconnect the ribbon cable
and internal 4-way connector to the control panel before securing the panel to the unit.
Note: Cable ribbon connector is polarised to ensure correct fitting.
Re-connect the mains cable: L, N, E,LS.
Re-attach the Electrical Cover.
Re-attach the front and rear covers off the unit.
Note: When the unit is converted from RH to LH the blue Vent-Axia logo will then be facing
the wall.

Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX.
UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA
SALES ENQUIRIES: Tel: [phone] Fax: [phone]
TECHNICAL SUPPORT Tel: [phone] Fax: [phone]
For details of the warranty and returns procedure please refer to www.vent-axia or write to Vent-Axia Ltd, Fleming Way, Crawley, RH10 9YX
474478 A © 2016 Vent-Axia Limited. All rights reserved. 0716
The Guarantee
Applicable only to products installed and used in the United Kingdom. For details of guarantee outside the United Kingdom contact your local supplier.
Vent-Axia guarantees its products for two years from date of purchase against faulty material or workmanship. In the event of any part being found to be
defective, the product will be repaired, or at the Company’s option replaced, without charge, provided that the product:-
Has been installed and used in accordance with the instructions given with each unit.
Has not been connected to an unsuitable electricity supply. (The correct electricity supply voltage is shown on the product rating label attached
to the unit).
Has not been subjected to misuse, neglect or damage.
Has not been modified or repaired by any person not authorised by the company.
IF CLAIMING UNDER TERMS OF GUARANTEE
Please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by post or personal visit. Please ensure that it is
adequately packed and accompanied by a letter clearly marked “Guarantee Claim” stating the nature of the fault and providing evidence of date and
source of purchase.
The guarantee is offered to you as an extra benefit, and does not effect your legal rights