Ventry BTV110 Instruction Manual

115mm
115mm
23”
(58cm)
20kg
(44lbs)
IP-BTV110-V2-VT2BX-271009-03
BTV110
flat panel wall mount
REG. DESIGN NO: 566831-0001
8mm (5/16”)
masonry bit or
5mm (3/16”) wood bit
2009 Bennett Technologies Limited. All rights reserved. B-Tech Audio Video Mounts is a division of Bennett Technologies Limited.
B-Tech, Better By Design & Ventry are registered trademarks of Bennett Technologies Limited. All other brands and
product, names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE.
Suitable for VESA and non-VESA screens up to 23”
Mounts screen only 15mm from the wall
Simple hook-on installation with all mounting hardware included
INSTALLATION SAFETY
INSTRUCTIONS
CAUTION: This wall mount is intended for use only with the maximum
weights indicated. Use with flat screen heavier than the maximum
indicated may result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read
and properly understood. Please keep these instructions for future reference.
B-Tech International Limited, its distributors and dealers are not liable or responsible for
damage or injury caused by improper installation, improper use or failure to observe
these safety instructions. In such cases, all guarantees will expire.
B-Tech International Ltd recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during installation
as most AV equipment is of a fragile nature, possibly heavy and easily damaged if
dropped. If you do not fully understand the instructions or are not sure how to install this
product safely, then please consult a professional for advice and/or install this product
for you.
Failure to mount this product correctly may cause serious injury or death both during
installation and at any time thereafter. Do not mount any AV equipment that exceeds the
specific weight limit of the product you are installing. This weight limit will be clearly
stated on each product and its packaging and will vary from product to product.
General
Please pay careful attention to where this product is located. Some walls are not
suitable for installation.
If located in a public or frequently populated area ensure that the product is out of the
immediate reach of people. If any AV equipment is to be suspended over the likely path
or location of people then great care should be taken to secure all parts of the installation
from falling. If you install this product on drywall it must be securely fixed to a wooden
stud, concrete block or other permanent structure behind the drywall board. Installing on
drywall boards alone will not support the weight of most AV equipment. When drilling
holes in walls it is essential to avoid contact with electrical cables and water or gas pipes
contained within. Use of a good quality live wire detector and hidden object locator is
therefore recommended. Only drill into structures when you are sure it is safe to do so.
Product location
It is highly recommended that all wall fixing screws be used where supplied and that the
purpose of all other fixing hardware is fully understood. In some cases more AV
equipment fixing hardware will be supplied to accommodate different models of
equipment and set up configurations. The installer must be satisfied that any supplied
fixing hardware is suitable for each specific installation. If any fixing screws or included
hardware are deemed not sufficient for a safe installation then please consult a
professional or your local hardware store.
Fixing hardware
When routing cables take advantage of any built in cable management features that the
product might provide and ensure that all cables are tidy and secure. Check to see that
any moving aspect of the product can do so unhindered by any cabling. Some products
have moving parts and the potential to cause injury through the crushing or trapping of
fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installations double-check that
the work done is safe and secure. Double-check all necessary fixings are present and
are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made
as frequently as possible to ensure that safety is maintained. If in doubt consult a
professional AV installer or other suitably qualified person.
Hazard limitation

BTV110
INSTALLATION INSTRUCTIONS
1. Attach wall plate to either a concrete or stud wall.
i. Concrete wall. ii. Stud wall.
A2
1
A1
A1
1
2. Attach VESA plate .
3. Hook mount onto wall plate. 4. Fasten top screw to secure installation.
2
A
1
2

BTV110
PARTS LIST
3
A1
A2
Suitable for loads up to
20Kg (44lbs)
VESA PLATE
WALL PLATE
3 M4 X 10mm SCREW 1
1
1
M5.5 X 42mm WOOD SCREW 2
2
WALL PLUG
M4 X 10mm SCREW 4
PLEASE KEEP THIS PARTS LIST FOR FUTURE REFERENCE