Vents VUT 100 P mini Mounting instructions

USER’S OPERATION MANUAL
Air handling unit with heat (energy) utilization
VENTS VUT 100 P mini
VENTS VUE 100 P mini

2VUT(VUE) 100 P mini
CONTENT
3
3
3
4
4
5
6
6
7
8
9
10
11
12
12
13
14
14
14
Introduction..................................................................................................
Application.....................................................................................................
Delivery set....................................................................................................
Unit designation key..................................................................................
Basic technical data....................................................................................
Basic dimensions.........................................................................................
Safety requirements...................................................................................
Structure and operating diagram..........................................................
Mounting and setting-up.........................................................................
Condensatedrainage.................................................................................
Unit connection to power mains...........................................................
Unit operation and control logic...........................................................
Servicing and maintenance.....................................................................
Troubleshooting...........................................................................................
Storage and transportation rules..........................................................
Manufacturer’s warranty...........................................................................
Acceptance certicate...............................................................................
Connection certicate...............................................................................
Warranty card...............................................................................................

3
INTRODUCTION
APPLICATION
DELIVERY SET
This user’s manual combines technical description, operation and service manual, technical data
sheet and installation guidelines for the air handling unit with heat utilization VENTS VUT 100 P mini /
air handling unit with energy utilization VENTS VUE 100 P mini, hereinafter unit.
The unit described in this user’s manual is the air handling unit with heat utilization (VENTS VUT
100 P mini) or energy utilization (VENTS VUE 100 P mini) and is one the energy saving components
used in the buildings and premises. The unit is a complete unit and is not designed for independent
operation. The unit is designed to provide permanent controlled air exchange in houses, oces, ho-
tels, cafés, meeting halls and other mechanically ventilated premises as well as utilization of extract air
heat energy to warm up supply puried air.
The unit is designed for ceiling mounting.
The unit is rated for continuous operation always connected to power mains.
Operating medium must not contain any ammable or explosive mixtures, evaporation of
chemicals, coarse dust, soot and oil particles, sticky substances or brous materials or any other harm-
ful substances.
The unit is not designed to be used by children, physically or mentally disabled
persons, persons with sensory disorder, persons with no appropriate life experience
and/or expertise unless they are properly instructed about the device use or supervised
by the person in charge for their safety.
The unit can be operated by qualied experts after careful instruction about its use
and operation.
The unit shall be mounted in places inaccessible for children.
VENTS VUT (VUE) 100 P mini unit - 1 pce.;
User’s operation manual - 1 pce.;
Packing box - 1 pce.;
Speed switch P3-1-300. - 1 pce.

4VUT(VUE) 100 P mini
UNIT DESIGNATION KEY
Air capacity [m3/h]
Casing type
Compact casing.
Modication type
P– suspended.
Unit type
VUT  ventilation with heat utilization.
VUT  ventilation with energy utilization.
VUT 100 P mini
BASIC TECHNICAL DATA
The unit is designed for indoor application with the ambient temperature ranging from +1ºC (34
°F) up to +40ºC (104 °F) and relative humidity up to 80%.
Ingress Protection (IP) rating from solid objects and liquids:
IP 44 for the unit motors (protection from objects equal to or larger than 1.0 mm
and splashing water);
IP 22 for the assembled unit connected to the air ducts (protection from objects
equal to or larger than 12.5 mm and water tilted at +/- 15°).
The unit series designation key, the basic overall and connecting dimensions, external view,
technical data are shown in g. 1 and in tables 1 and 2.
The unit design is regularly improved, so some models can slightly dier from those ones described
in this manual.
VUT 100 P mini VUE 100 P mini
Weight [kg] 13 10
Heat exchanger type Aluminium Paper
Table 1

5
Fig. 1
595
497
215
175* 111*
105 105
213
112 129
Ø 125
Ø 125
81 81213
249
434 404 374
397
Ø 8.2
4 holes
BASIC DIMENSIONS
G 1/2”
* - for VUT 100 P mini only
Model VUT(VUE) 100 P mini
Speed min. med. max.
Voltage, 50 Hz [V] 1~230
Power [W] 30 38 56
Current [A] 0,18 0,23 0,34
Air capacity [m3/h] 57 78 106
Rotation speed [min -1] 1300 1950 2500
Noise level at 3 m [dBa] 24 32 41
Maximum operating temperature [°C] -25 up to +50
Casing material Aluzink
Insulation material Penophole
Heat insulation layer [mm] 15
Filter
extract G4
supply G4
Connecting air duct dia. [mm] 4  125
Heat utilization eciency [%] 68
Moisture utilization eciency [%] 65
Heat exchanger type cross-ow
Table 2

6VUT(VUE) 100 P mini
SAFETY REQUIREMENTS
DO NOT!
• Do not operate the unit beyond the specied temperature range or in an aggressive
and explosive medium.
• Do not connect clothes dryers or similar equipment to the ventilation system.
• Do not operate the unit in the air and dust mixture environment.
WARNING!
Mounting, servicing, connection and repair works are allowed after the unit is
disconnected from power mains.
While operating and mounting the unit consider the requirements of the present operation manual
as well as general requirements of all applicable local and national building and electrical codes and
standards.
Ground the unit before operating!
Before connecting the unit to power mains make sure that the unit is free of any visible damages or
any other foreign objects inside the casing that can damage the impeller blades.
Connection of the unit to power mains by duly qualied electricians only!
STRUCTURE AND OPERATING LOGIC
The unit design and operating logic of the unit is shown g. 2.
1 3 6 7 2
5 4
SUPPLY AIR
EXTRACT AIR INTAKE AIR
EXHAUST AIR
Fig. 2

7
While mounting the unit provide enough space for its servicing and maintenance. Suspend the
unit to ceiling by means of the threaded rod xed inside the threaded dowel, g. 3.
MOUNTING AND SETTING-UP
1. Supply fan
2. Extract fan
3. Plate cross-ow heat exchanger made of aluminium for the model VENTS VUT 100 P mini or
paper for the model VENTS VUE 100 P mini.
4. G4 Supply lter
5. G4 Extract lter
6. Thermostatic switch
7. Condensate drain pipe (for the unit VUT 100 P mini only).
Fig. 3
Minimum access distance for the unit
400
10
Fig. 4
Washer
Nut
Vibration-absorbing
rubber
Nut and counter-nut
min 10

VUT(VUE) 100 P mini
8
CONDENSATE DRAINAGE
The unit is equipped with a drain pipe for condensate drainage (only for the unit VENTS VUT 100
P mini). The connection of the unit to drain system is shown in g. 5.
Connect the condensate drain pipe (1), U-traps (3) and the drainage system with metal, plastic
or rubber pipes .
The pipes should be sloped down by min. 3 degrees.
Before starting operation of the unit ll the system with water and check that U-trap is always
lled with water. Make sure that the water drainage is correct. Wrong connection to drainage system
may result in unwanted water ingress to the room.
The unit with a condensate drainage system is designed for operation at the ambient tempera-
ture above 0C. If the unit is operated in the environment below 0C it must be thermal-insulated and
equipped with heating.
Check the correct installation of the U-trap considering low pressure in the system produced
by the supply fan (g.5). In this case the maximum developed pressure is 115 Pa and dimension A is
about 100 mm and dimension B is about 80 mm.
Fig. 5
To gain the best performance of the unit while mounting provide a straight 1 m duct section
in front and behind the unit . If the unit is installed at the air duct inlet or outlet it shall be equipped
with a grille with the mesh width up to 12.5 mm or any other protecting device to prevent free access
to the unit fans.
2 4 13
А
В
min 3°

9
UNIT CONNECTION TO POWER MAINS
Cut power supply o before any operations with the unit. The unit shall be con-
nected to power mains by duly qualied electricians. The rated values of the electrical
parameters are shown on the rating plate. Any modications of the internal connections
are not allowed and will void the warranty.
The unit is rated for connection to single-phase ac 230 V / 50 Hz power mains.
For the unit connection use insulated, durable and heat-resistant wires, cables not less than 0.75
mm2. The unit is connected to power mains through the terminal block in compliance with the wiring
diagram and terminal designation on the g. 6. The wiring diagram is also shown inside the terminal
box. The terminals on the wiring diagram are marked in compliance with the actual marking in the unit.
Route the wires into the terminal box through an airtight screwed cable gland located at the side
wall of the unit to preserve the electric rating class.
Connect the unit to power mains through the external magnetic circuit breaker integrated into the
xed wiring system with min. overload protection 1A.
Fig. 6
QF - automatic circuit breaker
(not included into delivery set);
S1 - speed switch;
X1 - terminal block.
~ 230 V,
50 Hz
QF X1
L
N
PE
SL
1
2
3
low
middle
high
L
N
PE
123
С В
S1
1
2
3
4
5
6
7
8

10 VUT(VUE) 100 P mini
UNIT OPERATING AND CONTROL LOGIC
The operating logic of the unit is as follows.
Sensible heat energy contained in the extract air ow is transferred in the VENTS VUT 100 P mini
unit heat exchanger to the cold intake air ow from outside to warm it up before supplying it to the
room.
Both sensible and latent moisture energy contained in the extract air are transferred in the VENTS
VUE 100 P mini unit heat exchanger to the cold intake air ow from outside to warm it up before sup-
plying to the room .
The paper heat exchanger of the VENTS VUE 100 P mini unit operates as a moisture balancer in
case of too low outdoor humidity or as a air dryer in case of high outdoor air humidity. Due to high
hygroscopic features of the heat exchanger materials the unit does not need condensate drainage.
Due to energy and heat utilization by the heat exchanger minimizes thermal energy losses and
saves heating costs during cold season.
Air ow in the unit in regulated by the two-speed switch P3-1-300, further the switch. View of the
switch as shown in g. 7.
The thermostatic switch 6 (g. 2) in the unit casing provides frost protection of the heat exchanger
during cold season. The thermostatic switch switches the supply fan o if the heat exchanger needs to
be heated with the extract air heat energy.
The thermostatic switch is regulated manually by turning the control knob to set the required ther-
mostatic switch setpoint. The threshold switching value is set individually depending on the operat-
ing conditions of the unit. The recommended thermostat setpoint is +3ºC (factory setting). Rotate the
switch control knob to set the setpoint threshold.
Fig. 7
OFF
12
3