Vera Ezlo Secure User manual

User Guide
Smart Home Controller

User Guide 2
Chapter 1
Introduction
Package contents
Features
LEDs
Chapter 2
Initial Installation
Requirements
Procedure
Chapter 3
Configuration
Configuration Program
Appendix A
Specifications
Regulatory Appro als
Table of contents

User Guide 3
Chapter 1
Introduction
This chapter provides an overview of the Ezlo Secure Gateway’s
features and capabilities
An always-on solution that works even in the event of a power or
internet outa e, the Ezlo Secure is a feature-rich control hub that keeps
users in control of their home from anywhere, at any time. It oers
control for Z-Wave, Zi bee, and 2GIG devices while also enablin control
of Wi-Fi devices paired to Amazon Alexa or Goo le Assistant. It features
local control for fast responsiveness, and throu h the Vera app ives
customers remote access, personalized notifications, and scene creation
ability.
Package content
The Ezlo Secure comes with an ethernet cable, power adapter, and quick
start uide. Each Ezlo Secure is shipped under a unique serial number
shown on the packa in . Users should retain packa in for reference.
Features
CPU: Quad-Core Cortex-A7 ARM
Memory: 16GB EMMC Flash and 512MB DDR3
LAN: 10/100 Ethernet port with RJ45 connector
Z-Wave Plus, 700 Series
Zi Bee 3.0
345MHz 2GIG receiver
802.11 /n/ac Dual Band WiFi 2.4 & 5GHz
4G/LTE supportin bands B2/B4/B5/B12/B13/B14/B66/B71
Bluetooth Low Ener y 5.0
Host USB 2.0 port
Reset buon
Top surface RGB LED
5V/3A power

User Guide 4
LEDs
Top-mounted LEDs
Rear/Top Panel
Bootin / Power ON
Power port
Buon on
the top
Ethernet port
USB Port
Reset
Bootin recovery partition
Bootin application partition
System has booted but firmware
not started
Firmware has started
Red
Connect the supplied power
adapter here
Multifunctional user buon
Use a standard LAN cable (RJ45
connector) to connect your router
to the port.
The connector is a USB host with
support for mass stora e devices.
Resein the device to Factory
Sein s will remove all the
information about included
devices, scenes created, House
modes sein s, etc.
Push and hold the RESET buon at
least 5 sec (on Ezlo Secure LED
starts blinkin RED), After that
your Ezlo controller will be reset to
factory defaults.
Red
Green Blue
Yellow
Blue
Slow blinkin
Slow wavin
Power
Reset
LAN

User Guide 5
Chapter 2
Initial Installation
This chapter covers the software installation of the Ezlo
Secure Gateway.
Requirements
Use a standard 10/100/1000 BaseT network (UTP) cable with
RJ45 connector
Procedure
1. Choose an Installation Site
Select a suitable place to install the Ezlo Secure Gateway.
2. Connect LAN Cable
Use a standard LAN cable to connect the device to the Ethernet port on
the Ezlo Secure Gateway.
3. Power Up
Connect the supplied power adapter to the Ezlo Secure Gateway. Use
only the power adapter provided. Usin a dierent one may cause
hardware dama e.
4. Check the LEDs
• The LED should be ON.
Power
Reset
LAN
Power
Reset
LAN
Connect the AC Power
Adapter to your Ezlo Secure.
Connect your Ezlo Secure to
your internet ateway usin
an Ethernet cable.

User Guide 6
Chapter 3
Configuration
This chapter provides Setup details of the System.
Configuration Program
The Ezlo Secure Gateway can oer customers seamless communication
between devices while at home or away. This ateway is desi ned to
provide complete connectivity with all certified devices includin ,
security systems and Zi Bee/ZWave/2GIG devices.
Preparation
1. Install the VeraMobile application on your phone
iOS
Go to App store
Search for VeraMobile app and install it
Android
Go to Goo le Play store
Search for VeraMobile app and install it
2. Connect the AC Power Adapter to your Ezlo Secure
3. Connect your Ezlo Secure to your internet ateway usin a LAN cable
Using the mobile application
1. Open the VeraMobile app on your mobile phone
2. If you don’t have an account after you open the app select New to
Vera option and select from the list Ezlo Secure.
3. Select Wired setup. The app will walk you throu h the rest steps.
4. Select Scan Barcode you will see the screen with a camera and Add
manually buon.
5. Tap Add manually and enter the serial number and MAC address
(printed on the sticker)
6. You will see the con ratulations screen with Ezlo Secure.
7. Ezlo Secure is ready to use.

User Guide 7
Appendix A
Specifications
Ezlo Secure
Model
Dimensions
Operatin Temperature
Buons
Network protocol
Network Interface
LEDs
Power adapter
Ezlo Secure
194x164x46 mm
0Cto40C
Functional buon on the top
surface and reset buon on the
back surface
TCP/IP
1 * 10/100 BaseT (RJ45) LAN
connection
RGB led
5V, 3A

User Guide 8
Regulatory Approvals
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
g interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a ClassBdigital device, pursuano Part 15 of the FCC Rules. These
limits are designed to provide reasonable protec- tion against harmful
interference inaresidential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur inaparticular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged
to try to correche interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
The antennas used for this transmier must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmier.
includin
For indoor use only. Device does not operate in Band 5600-5650MHz.

User Guide 9
Industry Canada Licence Exemption
This device complies with Industry Canada licence-exempt RSS
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
ma
For indoor use only. Device does not operate in Band 5600-5650MHz.
y cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
fonctionnement.
Pour usage intérieur uniquement. L’appareil ne fonctionne pas dans la bande 5600-5650 MHz.