Vertex T22.3 User manual

TREADMILL T22.3
OWNER’S MANUAL

1
2015/3/9V1.0+V1.0
Content
1. Overview Drawing.........................................................................................................2
2. SAFETY INSTRUCTION ..............................................................................................3
2.1. Power Requirement ...........................................................................................5
2.2. Add Lubricant.....................................................................................................6
2.3. ADD SILICONE..................................................................................................7
2.4. Level Adjustment................................................................................................8
2.5. Power Switch.....................................................................................................8
2.6. Running Belt Adjustment....................................................................................8
3. Assembly Instructions...................................................................................................9
3.1. Pre-Assembly Check List...................................................................................9
3.2. Hardware Pack ................................................................................................10
3.3. Assembly Steps ...............................................................................................11
4. The operation instruction of electronic meter..............................................................14
4.1. Electronic meter structure_ A LC Screen Section ............................................15
4.2. Electronic meter structure_B Substance Keys.................................................15
4.3. Electronic meter structure_C Substance Keys.................................................16
4.4. Electronic meter structure_Outter Installation Section .....................................17
5. Display page introduction ...........................................................................................18
5.1. Simple user interface：....................................................................................18
5.2. Startup page.....................................................................................................18
5.3. Resident area...................................................................................................18
5.4. Standby page...................................................................................................19
5.5. Program control set page.................................................................................19
5.6. Exercise storage device optional page (running and fitness with the exercise
record device).............................................................................................................20
5.7. Pages of the exercise ......................................................................................21
5.8. Exercise Course Page .....................................................................................26
6. Heart Detection Introduction.......................................................................................27
6.1. Heart Rate Sensor System ..............................................................................28
6.2. Regional heart rate exercise............................................................................28
7. Sports and fitness program.........................................................................................29
7.1. Overview of sports and fitness program...........................................................29
7.2. Program Illustration..........................................................................................29
8. Program Set ...............................................................................................................39
8.1. Enter and Exit Engineer mode.........................................................................39
8.2. Setting Metric or Imperial system Units............................................................40
8.3. Time zone setting.............................................................................................40
8.4. Language.........................................................................................................40
8.5. Setting Metric or Imperial system Units............................................................40
8.6. Machine information.........................................................................................40
8.7. Wi-fi setting......................................................................................................41
8.8. Power setting...................................................................................................41
8.9. Update for the software....................................................................................41
8.10. Value Setting................................................................................................42
8.11. Debug Log....................................................................................................42
8.12. TV Setting.....................................................................................................42
8.13. Others...........................................................................................................43

2
2015/3/9V1.0+V1.0
1. Overview Drawing

3
2015/3/9V1.0+V1.0
2. SAFETY INSTRUCTION
When using this product, basic precautions should always be followed, including the
following:
Please read the instruction carefully before starting to use this product.
DANGER –To reduce the risk of electric shock：
Always unplug this product from the electrical outlet immediately after using and before
cleaning.
WARNING –To reduce the risk of burns, fire, electric shock, or physical injury：
1 The product should never be left unattended while plugged in. Unplug the product from
the outlet when not in use.
2 Close supervision is necessary when this product is used by or near children, invalids,
or disabled person.
3 Be sure to use the product only for its intended use as described in this manual. Do not
use any attachment not recommended by the manufacturer in order to avoid any
danger or accidents.
4 Never operate the product if it has a damaged cord or plug, if it is not working properly,
if it has been damaged, or dropped into water. Please return the product to the service
center of seller for examination and repair.
5 Do not carry this product by the supply cord or use the cord as a handle.
6 Keep the cord away from hot surfaces or ground.
7 Never operate the product with the air vents blocked. Keep the air vents free of lint, hair,
etc.
8 Never drop or insert any objects into any openings.
9 Do not use or operate outdoors.
10 Do not operate where aerosol (spray) products are being used or where oxygen is thin.
11 Before turning the product power off, turn all controls to the off position then remove the
plug from the outlet.
12 Connect the product to a properly grounded outlet only.
13 If the power cord is damaged, be sure to ask the manufacturer for replacement to avoid
accidents. The seller and correlative qualified professionals are as well as eligible.
14 This appliance is not intended for use by person (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
15 Incorrect or excessive training may cause injuries.
16 The equipment shall be installed on stable base and properly leveled.
17 A safety area of 2,000mm x 1,000mm should be kept behind the equipment.
18 Maximum user weight is 180 Kgs.
19 The safety level of the equipment can be maintained only if it is examined regularly for
damage and wear.
20 Any of the adjustment devices that could interfere with the user's movement should not
be left projecting.

4
2015/3/9V1.0+V1.0
21 Users correct ergonomic position on the equipment shown in Figure
22 Before using this product, you should step on it then turn on the product. Do not turn on
the treadmill before step on it.
23 Running surface is 555*1575mm
24 The appliance is intended for commercial use.

5
2015/3/9V1.0+V1.0
2.1. Power Requirement
This treadmill needs special power supply:
Power Voltage（V）
Frequency（HZ）
Rated Current（A）
100
50/60
18
120
50/60
18
200
50/60
9
220
50/60
9
230
50/60
9
240+
50/60
9
Wirings should be transported according to the electric law of the local country. High
pressure wires, low pressure wires and underground wires should be transported
separately and can’t connect with or twist other wires.
Improper connection of the grounding plug can result in the risk of electric shock. Check
with a qualified electrician or serviceman if you are in doubt as to whether the products are
properly grounded. Do not modify the plug provided with the product –If it will not fit the
outlet, have a proper outlet installed by a qualified electrician.
Figure
Grounding methods
GROUNDED
OUTLET

6
2015/3/9V1.0+V1.0
2.2. Add Lubricant
Use the Hex Wrench to unscrew the hex screws inside the Rear End Cap. Then pull the
belt up and daub some SILICON to the center of the board.After that, adjust the belt to the
center of the deck, followed by tightening the screw to the original set. Adjust the running
belt according to the above steps. Half a month should be checked once

7
2015/3/9V1.0+V1.0
2.3. ADD SILICONE
Time of add SILICONE
When suggested time of adding SILICONE is achieved, please extend your hand to the
center of the running board to make sure whether there is any SILICONE before adding. If
no SILICONE on the running board, please add 30cc SILICONE to the running board. If
there is still a little SILICONE, add 15cc SILICONE to the running board.
Area of adding SILICONE
Add SILICONE from the center of the running board to the running belt ’s the left and right
side which should minus 6 cm.

8
2015/3/9V1.0+V1.0
2.4. Level Adjustment
The treadmill will wobble during workout and the incline angles will be affected if it is placed
on uneven ground.
The level adjustment method is as follows:
1 Turn A anticlockwise to loosen it
2 Adjust B to the proper height
3 Turn A clockwise to tighten it.
4 The left side adjustment method is same as the right side.
2.5. Power Switch
The Power Switch is on the bottom panel of the treadmill. 1 means on, 0 means off.
2.6. Running Belt Adjustment
After assembling the treadmill, check the operation of the running belt.
First, make sure the power supply is correct. After starting the treadmill, stand on the two
sides of the pedal(At the very start, don’t stand on the running belt).Press QUICK START
key and then increase the speed to 4.0MPH(6.4KPH) by pressing + key.
If the running belt is moving towards the right side：
Turn the right button 90°clockwise and the left button anticlockwise 90°. You will find the
belt return to the center position automatically.
If the running belt is moving towards the left side：
Turn the left button 90°clockwise and the right button anticlockwise 90°. You can also find
the treadmill return to the center position automatically.
If you find that the belt has not moved to the proper position, please repeat the steps above.
Note：When adjusting the button, the angle can not exceed 90° which will make it
impossible to adjust the belt to the proper position.

9
2015/3/9V1.0+V1.0
3. Assembly Instructions
Ready the operation instructions carefully before use, then choose a flat position to
assemble.
This treadmill also can use other way to account the HRC. When in fitness,
user can wear the chest pulse belt and the HRC will show in Pulse windows.
3.1. Pre-Assembly Check List
ITEM
Description
Qty
A
Computer Console
1
B
Stuff Holder
1
C
Frame
1
D
Left Handrail
1
E
Right Handrail
1
F
Inner handrail cover L
1
G
Inner handrail cover R
1
H
Outer handrail cover L
1
I
Outer handrail cover R
1
J
TPR handrail upper cover set L
1
K
TPR handrail upper cover set R
1
L
Computer decorative cover
1

10
2015/3/9V1.0+V1.0
3.2. Hardware Pack
ITEM
Description
Qty
a
Cks hex screw M10xP1.5x25
8
b
Truss hex screw∮13
4
c
Truss Philips Screw M5xP0.8x12
4
d
Screw Φ4x16
4
e
Philips screw M5xP0.8x15
4
f
Truss hex screw M8xP1.25x20
2
g
Spring washer M8
2
h
L hex wrench+ Philips Screwdriver 5mm
1
i
L hex wrench 10mm
1
j
L hex wrench 8mm
1
k
SILICONE
1
l
Spring washer M4
2
m
Truss Philips Screw M4xP0.7x10
2
n
Power Cord Switch Cover
1
o
CABLE Adapter
1

11
2015/3/9V1.0+V1.0
3.3. Assembly Steps
STEP 1
Release cross screw on frame(c) for motor upper cover fixing and take off upper motor
cover, fix the truss hex screw of upright tube into gourd hole as figure 1-1 and push it
forward. Then pull the control wire & other wires out with guide thread attached in upright
tube and fix the upright tube L,R(D,E) with screw(a), but do not tighten. Tighten outer
handrail cover L&R(H,I) on upright tube L,R with screw(e), at last tighten inner handrail
cover L,R(F,G) with screw(c,d).
STEP 2
Make control wire& other wires through the hole of stuff holder set(B), make sure the wires
is not pressed and fix the truss hex screw of stuff holder set(B) into gourd hole of upright
tube as figure 2-1, push it forward. After finished, tighten stuff holder(B) with screw(b) and
tighten the screw(a) that fixing the upright tube L,R. At last, cover the upper motor cover
back to frame(C) and tighten with cross screw.
Philips Screw
Philips Screw
Philips Screw
Philips Screw
Philips Screw
Philips Screw

12
2015/3/9V1.0+V1.0
STEP 3
Put computer console(A) on stuff holder(B) as figure 3-2, connect the control wire & other
wires of stuff holder(B) with wires of computer as figure 3-1. The put the connected wires
down to the place under flask holder set, that assembled before and fix with screw(f) &
spring washer(g), cover the computer decorative cover(L) and tighten with screw(d), when
cover it, please be sure to not press the wires. At last, tighten TPR handrail upper cover set
L,R(J,K) on stuff holder with screw(c).
Attention:
(1) When connect the wires, if the connecting is successful, it will have a voice.
(2) TV cable(lower) is ready for TV systems using
(3) To avoid danger, always assemble the treadmill with more than two workers, do
not assemble alone.
(4) When assembling the console, one person should hold the console to prevent
them from falling.
Internet wire (lower) is prepared for the internet system.
Hub plate connecting wire upper
Control wire upper
Control wire lower
TV cable lower
Power wire lower
TV cable upper
Power wire upper
Internet cable upper
Internet cable lower
Hub plate connecting wire lower

13
2015/3/9V1.0+V1.0
STEP 4
Inset power wire into power wire socket as figure showing, then cover the power wire switch
cover(n) and tighten with screw(m), spring washer(I). Finished as figure 4-1.
Attention: cable transferring connector(o) is ready for TV cable systems using as
figure 4-2
Internet adapter connector is prepared for the adaption of the internet system, as
picture 4-2
Power wire

14
2015/3/9V1.0+V1.0
4. The operation instruction of electronic meter
This treadmill can provide a simple and easily operated electronic meter. Users can input
personal data by the electronic meter and set each exercise target.
This is the presetting hole, and we recommend that the internet hole under the machine
frame should be the main hole, and this hole and the one behind computer console cannot
be plugged with internet wire at the same time which will lead to the mixture of the digital
signal.
Ethernet
C-safe

15
2015/3/9V1.0+V1.0
4.1. Electronic meter structure_ A LC Screen Section
Position Section
Function Instruction
Information condition
display area
Display each condition information before exercise, during
exercise and after exercise.
Touch operation area
The screen area has touch function. On the screen, there are
operation keys for each page. Except for pressing once, part
keys support long time pressing, finger drag and rotating.
Picture display area
Display multiplayer picture.
4.2. Electronic meter structure_B Substance Keys
Name of Keys
Function Instruction
START
1. If the electronic meter is in log in and standby page and if press this
key, the electronic meter can turn to Quick start mode directly.
2. If the electronic meter is in the program setting and if press this key,
it can ensure the setting and turn to remote controlling exercise mode.
3. Under pause state, press this button to liberate pause, and return to
exercise mode and the speed and incline will come to the state as the
state before pause.
STOP
1. If the electronic meter is in log in page, if press this key, the
electronic meter can turn to standby mode directly.
2. If the electronic meter is in standby mode, when the remote
controlling option list is opened, if press this key, the electronic meter
can shrink the remote controlling option list.
3. If the electronic meter is in setting page, if press this key, the
electronic meter can return to standby mode.
4. The exercise in this electronic meter can to divided into 2 modes:
(4-1)with pause function：Pressing 1 to pause, and pressing 2 to end
exercise and enter exercise course report.
(4-2) without pause function: end exercise directly and enter exercise
course report.
SPEED↑/↓
Increase or
decrease speed
during exercise
1. If the electronic meter is in standby page, when the remote
controlling option list is opened, it can switch to next remote
controlling program by turns (circulation)
2. If the electronic meter is in setting page, the function is to switch to
next setting program (circulation)
3. During exercise, the keys can be pressing once or long time
pressing, the climax is 15.6mph (25.0km), the bottom line is
0.5mph( 0.8km).
※When the key is long time pressed, the data will change rapidly.
On account of safety, only 5.0kph (3.1mph) can be increased or
decreased once, until the key is liberated and pressed again.
※Under specific remote controlling, the speed is controlled by
computer and this key is invalid at that time.
INCLINE↑/↓
1. If the electronic meter is in standby page, by moving the cursor the

16
2015/3/9V1.0+V1.0
Increase incline
angle during
exercise
remote controlling program can be chosen.
2. If the electronic meter is in Training remote controlling setting page,
the Level bar can be adjusted directly (single direction)
3. If the electronic meter is in Goal remote controlling setting page,
the electronic meter can switch to Manual、Hill、Interval or
Random(circulation)
4.During exercise, the key can be long time pressed or pressed once,
the climax is 20.0%, the bottom line is 0.0%, STEP 0.1%.
※Under specific remote controlling, Incline is controlled by computer,
and the key is invalid at that time.
4.3. Electronic meter structure_C Substance Keys
Name of Keys
Function Instruction
Remote
controlling swift key
If the electronic meter is in standby page, it can turn to Goal
and Target_Time setting page directly.
Fan function key
Press this button to turn on/off the fan during exercise. After
starting, the fan is in set high speed status.
Fan function key
If the electronic meter is in standby page, if the press the key, it
can open the Fit Test option list.
Remote
controlling swift key
If the electronic meter is in standby page, if the press the key, it
can open the Fit Test option list.
Remote
controlling swift key
If the electronic meter is in standby page, if the press the key, it
can open the Goal setting page.
Remote
controlling swift key
If the electronic meter is in standby page, if the press the key, it
can open the Training option list.
Remote
controlling swift key
If the electronic meter is in standby page, if the press the key, it
can open the HR Control option list.
Remote
controlling swift key
If the electronic meter is in standby page, if the press the key, it
can open the Physical Test option list.
CLEAR
1. If the electronic meter is in log in page, the function is to skip.
2. If the electronic meter is in setting page, the function is to
recover the data which was setted before and clear other data.
3. During exercise, under warm uo and cool down, the function
is to skip.
ENTER
1. If the electronic meter is in standby page, the key is to
ensure the remote controlling program choose by the cursor.
2. 1. If the electronic meter is in standby page, when the
remote controlling option list come out to ensure the option.
3. If the electronic meter is in setting page, the key is to ensure
the program and the data input.
INSTANE INCLINE
During exercise, the function is to stop. Pressing once is to
start, and after starting 0-9, the key is swift key for incline.
INSTANE SPEED
During exercise, the function is to start, and after starting 0-9,
the key is swift key for incline. If press INSTANT INCLINE key
is to stop.
NUMBER 0~9
1. As the data input entry at the remote controlling page, the
function is to input data(only the positive integer is acceptable)
2. During exercise, as the data from speed or incline input key

17
2015/3/9V1.0+V1.0
(only the positive integer is acceptable), the time is within 2
seconds, beyond the time, the data cannot be input.
WAKE
After long-time without operation, the system will turn to
energy-saving mode, and stop automatically. If press this key,
the treadmill will recharge again.
Open time is about 30-35 seconds.
4.4. Electronic meter structure_Outter Installation Section
D. The fixed hook
with IPod wires
When IPod connection wires are not used, twine them as U
shape and hang them on the hook.
E1. USB Hole
(1) This holes can be used for Andriod device charging and
the output power supply is 5V/1A.
(2) This holes can be used for software updating and
maintenance.
E2. Earphone Hole
This hole can connect 3.5mm voice output device, such as
earphone.
E3. IPod connecting
wire
This wire can connect iOS device through the electronic
meter and the following functions can be used:
(1) Charging function,
(2) Reading the sound source and video inside the device.
(3) Nike+ function.
F. The air outlet holes
of fan
The air outlet angle can be adjusted by hand.

18
2015/3/9V1.0+V1.0
5. Display page introduction
5.1. Simple user interface：
The simple and obvious buttons and icons will assist users to operate as the users
wish to finish all settings and the control during exercise.
UI design of the electronic meter comes from our long term experience in fitness
equipment field, the special new technical function and users’ angle. The designed
operation environment is the fittest.
5.2. Startup page
This electronic meter isAndriod system and the loading picture can be displayed during
startup. The total loading time of the system is about 35s.
5.3. Resident area
There is a commonly existed status column at the Top right of the picture to assist users to
make an inspection at any time.
Wi_fi signal intensity
It is used for confirming the online quality of wireless network of the electronic
meter.
The online status of local area network:
It is used for confirming the online quality of local area network of the electronic
meter.
Language switch section
To switch the words on the screen for the users, and after choosing the language,
the system will switch automatically. During the switch, other keys are invalid.
※This language switching is real-time. When the electronic meter is turned on, the
system language can return to the default automatically which can be set under the

19
2015/3/9V1.0+V1.0
engineering mode.
※Resident area only display at the standby page under the non-exercise status.
5.4. Standby page
Choose Quick start or other program control in this page. Go back to this page whenever
the exercise is over.
5.4.1. Date, time and address of the system will be shown in the page center.
5.4.2. Bottom of the page is menu area of program control, total 2 pages. Change to
the next page in the method of left or right sliding. Some program control has
sub-stage. Pop-up sub-menu after pressing program control title
5.4.3. Safety switch removal status
Whenever the safety key from the treadmill is removed, all the action will be
stopped immediately, and the picture will turn to this page, and the words
showed on the page is ”Safety Key removed”, at that time, any key and action
cannot be operated until the safety key is plugged into again.
5.5. Program control set page
5.5.1. Choose any program control in standby page, apart from Quick start, and then
enter into the set page of the program control.
5.5.2. Input the age, weight, gender…of the user in specific program control, to be
substituted into the computational formula of the SPC.
5.5.3. After the set is finished, press start key, then enter into storage device ahead
the exercise, choose the page.