VESTEL LCD Series User manual

LCD SERIES MANUAL
1

LCD SERIES MANUAL
2
INDEX PAGE
ELECTRICAL COMPONENTS 3
PLASTIC COMPONENTS 9
DISASSEMBLY 12

LCD SERIES MANUAL
3
1. ELECTRICAL COMPONENTS
1.1 Circulation Pump
•Fırçasız Doğru akım motor
•0 –3400 RPM aralığı
•Sargı değerleri ölçülemez.
•Termal koruması yazılım kontrollüdür.
•Pompa çıkışı 0 – 80 lt/dk 0 –400 mbar
•Güç 0 -60 watt arasıdır.
Elektronik kart kontrollü değişken devirli motordur.
Saat yönünün aksi yönde dönmektedir.
Kauçuk askılar ile alt tabana monte edilmiştir.
1.2 Drain Pump
Voltage : 220/240 Volt
Frequency : 50 Hz
Total Power : 30 W
Flowrate : 17 –21 lt/dk
Coil Resistance : 143 Ω %± 7
Coil Isolation Class : F
Thermal Protection : 120 ° C
1.3 Heater Casing Group
1.3.1 Heater
Voltage : 220/240 V
Total Power : 2000 W
Resistance : 23.95±15 Ω
Yıkama suyunun ısıtılması için kullanılmaktadır.
Isıtıcı kurutma sürecinde aktif değildir. Havuza
monte edilmiş ve yıkama pompasının besleme
kenarına yerleştirilmiştir.

LCD SERIES MANUAL
4
1.3.2 NTC
Thermal Protection 83±3 ° C
Temperatures;
25°- 5000Ω %±5.0
35°- 3300Ω %±5.5
55°- 1520Ω %±6.5
63°- 1174Ω %±7.5
80°- 670Ω %±8.0
90°- 488Ω %±8.5
1.3.3 Pressure Switch
Voltage : 220/240 V
Frequency : 50 Hz (16 A –3 Pins)
1.3.4 Diverter
Voltage : 220/240 V
Frequency : 50 Hz
Power : 8 W
Resistance : 6840±٪5 Ω

LCD SERIES MANUAL
5
1.4 Detergent DispenserKabı
Detergent Compartment:
Main wash compartment : 40 cm³ (25/15)
Prewash compartment : 5 cm³
Aid Rinse Departmant:
Aid rinse cap : 150 cm³
Factory outlet setting position : 3. seviye
Detergent Dispenser Bobbin:
Voltage : 220/240 V
Frequency : 50 Hz
Resistance : 4450 ±10 Ω
Detergent Dispanser Rinse Aid Sensor:
Voltage : 250 V
Switched Current : 16 (4) A
Current Through Closed Contact: 2,5 max.
1.5 Water Inlet Valve
Voltage : 220/240 Volt
Frequency : 50-60 Hz
Total Power : 6 W
Flowrate : 2,5 lt/dk
Resistance : 3750 ±٪10 Ω ( 20 Cº )
Single inlet and single outlet standard single
coil selenoid valve. It is assembled to the
basement and connect to the airbreak by hose..

LCD SERIES MANUAL
6
1.6 Water Softener
1.6.1 Regeneration Valve;
Voltage : 220/240 V
Frequency : 50/60 Hz
Total Power : 6 W
Resistance : 4130±٪10 Ω ( 25 Cº )
Regeneration valve is assembled on
the water softener.
1.6.2 Salt Sensör;
Voltage : 250 V
Currency : 16 (4) A
It is assembled to the water softener. It warns if the
salt is less than requested quantity
1.7 Door Lock ;
It is a mechanical lock/release system that
is closing the door, supplying the connection of
electrical parts in the machine and cutting off the
connection.
Akım : 16 (4) A

LCD SERIES MANUAL
7
1.8 ON/OFF Button;
Button is assembled in the control panel unit.
On / Off ( two pole ).
Voltage : 250 V
Currency : 50mA
1.9 Turbo Fan Motor;
Total Power : 15 W
Voltage : 220/240 V
Frequency : 50 Hz.
Resistance : 238.6± ٪ 5 Ω
Coil solation Class : H
There is a thermal protector. Shaded pole motor,
two pole temperature is between -40 –150 Cº .
1.10 Parasite Filter;
Voltage : 220/240 V
Frequency : 50/60 Hz
0,1 uF (X1) + 2x0,027uF(Y2) + 1M Ω
It is used to prevent parasites from the main supply.
It has been assemblied to basement.

LCD SERIES MANUAL
8
1.11 Flowmeter ;
The amount of water intake is in precise control
1.12 Power Cord;
Type : Euro 3’lü 1 mm2 kesitli, bakır iletkenli
solation : TS 9760 H05VV-F
Plug : TS-IEC 60884–1 topraklı PVC enjeksiyon
Length : 1800 mm

LCD SERIES MANUAL
9
2.PLASTIC COMPONENTS
2.1 Drain Hose;
Drain hose maximum height : 110cm
Drain hose minimum height : 50cm
Drain hose maximum length : 400cm
2.2 Water Inlet Hose ;
Hose that is flat edge is assemblied to plug.
Another edge that is turned edge is assemblied to water
inlet valve. It must be adjusted for assembly direction.
2.3 Air Break ;
It measure water that comes to inlet dishwasher. And It
gives datas to electronic card.

LCD SERIES MANUAL
10
2.4 SALT CONTAINER;
It decreases hardness of water that comes from main
supply.
It includes 2 departments that “salt department” and
“recine department” with 2 types that is sensor or without
sensor.
2.5 Sump ;
Sump that is reservoir connects water in tube with
circulation pump and drain pump and heater casing..
2.6 Spray Arm Support;
It distributes water from divisor to upper and below spray

LCD SERIES MANUAL
11
3.7 L Spray Arm;
It transfers water from spray arm support to upper spray
arm
2.8 Upper Spray Arm;
It tranfers water from L spray arm to upper spray arm
There are two hole back of the upper spray arm.
The holes provides to work upper basket for
upper and lower position.
.
2.9 Upper Spray;
It distributes water from upper spray arm to dirty dishes
in the upper basket.

LCD SERIES MANUAL
12
2.10 LOWER SPRAY ARM;
It distributes water from spray arm support to dirty dishes in the lower basket

LCD SERIES MANUAL
13
DISASSEMBLY
CAUTION!: REMOVE ELECTRIC PLUG FROM THE SOCKET DURING THE DISASSEMBLY
1 ) ACCESSIBILITY
1.1) Top Plate
Remove two screws that fix the top plate at the back
b) Push the top-plate back and pull it up.

LCD SERIES MANUAL
14
1.2 ) Plastic Kick plate
a) Remove two screws fixing plastic kick plate
b) Remove the plastic kick plate as it is shown in the picture.

LCD SERIES MANUAL
15
1.3) Side panels
Before removing side panels ;
a) Firstly remove the top plate.
b) Than remove plastic kick plate.

LCD SERIES MANUAL
16
1.4 ) Front Panel
a) Remove six screws that fix the front panel.
b) Pull down the front panel as it shown in the Picture.

LCD SERIES MANUAL
17
1.5 ) Kick Plate Sheet Iron
a) Remove top plate, plastic kick plate and side panels.
b) Remove two screws tat fix the kick plate sheet iron.
c) Pull it down as shown in the picture.
1.6 Control Panel
a) Remove six screws that fix control panlel to the door inside sheet iron.

LCD SERIES MANUAL
18
1.7 ) Electronic Card
a) Remove the wires that are shown in the picture.

LCD SERIES MANUAL
19
WARNING: WHILE REMOVING WIRES, DO NOT PULL THEM FROM WIRES, PULL FROM THE
CONNECTOR.
b)Remove pcb box cover with pulling its plastic hinges.
c) Remove the wire which is between rotary switch and electronic card.

LCD SERIES MANUAL
20
d) Remove the electronic card from pcb box by removing pcb box’s plastic hinges.
1.8 ) Door Lock Group
a) Remove control panel group.
b) Remove two screws that fix the door lock group..