VEVOR HB6089-UL User manual
Technical Support and E-Warranty Certificate www.vevor.com/support
INSTRUCTION MANUAL
MODEL:HB6089-UL
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
- 1 -
MODEL:HB6089-UL
Have product questions? Need technical support? Please feel free to
contact us:
CustomerService@vevor.com
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
Commercial
Blender
- 2 -
Warning-To reduce the risk of injury, user must read instructions
manual carefully.
IMPORTANT SAFEGUARDS
Before using the electrical appliance, the following basic precautions should
always be followed including the following:
1. Read all instructions.
Before using it, check that the voltage of the wall outlet corresponds to the one
shown on the rating plate.
2. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or is dropped or damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair or
electrical or mechanical adjustment.
3.If the supply cord is damaged, it must be replaced by the manufacturer, an
authorized service agent, or a qualified technician to avoid a hazard.
4. Always disconnect the blender from the supply if left unattended before
assembling, disassembling, or cleaning.
5. Do not let cord hang over edge of table or hot surface. Be careful not to trip over
the long power cord when using the appliance.
Do not immerse the upper part of the blender in water, as this would give rise to
electric shock.
6. Avoid contacting moving parts.
7. Using accessories not recommended by the manufacturer may cause injuries
to persons.
- 3 -
8. Do not operate the appliance for other than its intended use.
9. Avoid splashing the food into the vent holes of unit body during blending.
10. The blender must be used in a working environment that is far away from
corrosive materials or oil pollution, and must be kept away from explosive and
flammable materials.
11. The metal blades are extremely sharp Please handle it carefully.
12. Be careful of potential injury from misuse.
13. In the process of using the appliance, it is necessary to hold it with both hands,
one hand holding the host handle, and the other hand holding the plastic
connector.
14. Switch off the appliance and disconnect from supply before changing
accessories or approaching parts that move in use.
15.Appliances can be used by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved.
SAVE THESE INSTRUCTIONS
KNOW YOUR COMMERICAL HAND BLENDER
- 4 -
- 5 -
TECHNICAL PARAMETER
Model
Input
Rated
Power
Tool
length
Rotating
speed（Min）
Rotating
speed
（Max）
Working
noise
HB6089
120V~
60Hz
500W
12 inch
4000
RPM/Min
18000
RPM/Min
≤85dB
（A）
HB6089
AC220-
240V；
50Hz
500W
12 inch
4000
RPM/Min
18000
RPM/Min
≤85dB
（A）
HB6089
120V~
60Hz
500W
20 inch
4000
RPM/Min
18000
RPM/Min
≤85dB
（A）
HB6089
AC220-
240V；
50Hz
500W
20 inch
4000
RPM/Min
18000
RPM/Min
≤85dB
（A）
HB6089
120V~
60Hz
750W
12 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
HB6089
AC220-
240V；
50Hz
750W
12 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
HB6089
120V~
60Hz
750W
16 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
HB6089
AC220-
240V；
50Hz
750W
16 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
HB6089
120V~
60Hz
750W
20 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
HB6089
AC220-
240V；
50Hz
750W
20 inch
8000
RPM/Min
20000
RPM/Min
≤85dB
（A）
- 6 -
ATTACHING AND DETACHING OF BLENDING ROD
Before attaching and detaching operation, it must be ensured that the
appliance stops working and its mains plug is unplugged.
How to attach:
1. Insert the blending rod into the threaded inner hole of the unit body. When
inserting, Align the slot of the connector with the ribs of the square aluminum cover
to ensure that the connector is inserted in place.
2. Tighten the lock nut to fix the blending rod firmly onto the body.
How to detach:
1. Loosen the lock nut.
2. Pull out the blending rod.
USING YOUR BLENDER
Before the first use, clean the blender according to the section of “QUICK
CLEANING”.
The time running unit without load can’t exceed 20s.
After the stirring rod is
assembled into place with the
main engine, rotate and
tighten the plastic parts, and it
is considered that the stirring
rod has been fixed.
- 7 -
IMPORTANT: Blades are very sharp;handle them with care. Ensure that the
hand-held blender is unplugged from the power outlet before installing or removing
attachments.
OPERATION METHOD
GETTING STARTED AND STOPPED
1. Check that the power button (3) is released.
2. Install the blending rod.
3. Connect the main unit to the power source.
4. Press the safety button (1) and proceed to the next step within 5s. If the
unlocking fails after 5s, press the safety button (1) again.
5. Press the power button (3) to start the hand blender (working time per cycle≤ 3
minutes, interval time between two cycles≥ 1 minute).
6. Release the power button (3), and the machine will stop automatically.
- 8 -
Continuous operation instruction
After completing steps 1-5 above, proceed to the following steps:
1. Press the lock button (4) when the power button (3) is pressed down, and the
red indicator lights up.
2. Release the power button (3) at this time, the hand blender will continue to work.
3. Press the power button (3) again, and the appliance stops, and the red indicator
is turned off
Speed adjusting instruction
After completing steps 1-5 above, proceed to the following steps:
1. Rotate the speed knob (2) to the desired speed setting
NOTE：
In order to better control the hand blender, it is recommended to hold the handle
and the bottom of the body. In addition, tilting the machine at a slight angle is
recommended to prevent the bell-shaped housing from touching the bottom of the
container. The ingredients in the container shall not exceed the MAX height of
the blending rod. Avoid splashing the food into the vent holes of unit body during
blending.
CLEANING AND MAINTENANCE METHODS
1. Unplug the appliance and remove the detachable blending rod.
2. Wash the detachable blending rod under running water without using an
abrasive cleaner or detergents. After cleaning the detachable blending rod, place it
upright so that any water that may have gotten in can be drained.The blending rod
is a dishwasher-safe component.
3. Wipe the motor unit with a damp cloth. Never immerse it in water for cleaning,
as an electric shock may occur.
4. Dry thoroughly.
QUICK CLEANING
Between processing tasks, hold the hand-held blender in the container half filled
with water and turn on for a few seconds.
CAUTION: Blades are very sharp; handle them with care.
- 9 -
REMOVAL/INSTALLATION OF BLADE ASSEMBLY
1. Align the blade assembly with wrench 1 and insert into it.
2. Align the blending head slot with wrench 2 and insert into it.
3. Unscrew clockwise to remove the blending rod.
FAULT ANALYSI
Fault
Phenomenon
Cause Analysis
Exclusion Methods
Indicator light is
not on
The power cord is not
plugged in.
1.Check the power cord to make
sure it is plugged in.
Indicator Light
on Product
Inoperative
1.Long working hours,
motor overheat
protection.
2.The machine itself is out
of order.
1.Wait an hour before reusing
2.Send to after-sales service
department.
- 10 -
Note:
Above are common trouble analysis and troubleshooting methods. For other
troubles, please contact our customer service department, or go directly to our
designated repair point for repair. Do not dismantle and repair yourself.
Address：
Manufacturer:
Made In China
Table of contents
