VEVOR K4002 User manual

Model: K4002

1. Power on: open the power supply knife of the machine cable. After power on, all
display units will light up once and the buzzer will drop once.
2. Power button: each furnace area has an independent power button. When you
want to start one of the burners, press the power button to turn on the power and enter
the standby state.
3. Standby state: Press the power button as described in the second operation and
enter the standby mode, which displays 0 (0 is not heated). The standby mode
automatically exits and returns to the shutdown state without any operation
for a long time.
The standby state is shown as follows: 0 is the standby state in the four furnace areas
4. Heating: For example, if you want to use the upper left furnace area for heating,
push the regulator in the standby state. When the digital display 0 turns into a
number, the furnace area enters the heating mode. As shown in figure 9:
ON/OFF
UP
DOWN
LOCK
TIMER

4.Power distribution: upper left 240V/1200W, lower left 240V/1500W,
upper right 240V/2000W, lower right 240V/1200W. (+ / - 10%)
5. Firepower adjustment: in heating mode, push the regulator, the digital gear from
1 to 9 is normal heating gear, and the P gear is rapid heating. After 3 minutes, it will
return to the 9 gear. Turn to 0 to stop heating.
6. Shutdown: In heating mode, hold down (hold down for two seconds) to exit
heating and return to shutdown state.
7. Child lock: long press the child lock key for 2-3 seconds to drop a sound to
lock or unlock, locked successfully child lock digital display Lo, shutdown or standby
with heating state can operate child lock.
After successfully locking, do not operate
any health except child lock.
Locked successfully as shown in figure:
8. Timing: This function is to set the shutdown time. In heating mode, press the
timing button to enter the preset timing. The default time is 00 minutes.
Switch adjustment time (progressive 1 minute, 99 minutes at most), the
adjustment is completed to stop the operation, digital flashing several times after
entering the steady setting success. Continuously press the timing button to set the
time of multiple furnace areas. After the setting is completed, the small dot flashes at
the lower right corner of the display digital number in the furnace area. The time
display in different furnace areas automatically switches to about 5 seconds, with the
small dot as a mark.
As shown in the picture, timing left upper furnace area: 99 minutes
34
9. Panel high temperature warning: there is still residual temperature on the furnace
panel after use, warning display H, be careful of scalding hands.
10. Product dimensions and precautions:
10.1. Product dimensions 770*520*82 (30.3*20.47*3.34 inches)
If not including the foot of the fuselage thickness is 65MM/2.55 inches
10.2. Opening roar size 760*500*150mm (29.92*19.68*5.9 inches)
11. The corresponding temperature of each section of fire
(set the numerical value for the program), the measured data obtained by
different working ring mirrors will have deviation.
Range 1--2--3--4--5--6--7--8--9--P ten stages Corresponding degrees
Celsius 60-80-100-120-140-160-210-240-270 degrees C ten segments Corresponding
to Fahrenheit 140-176-212-248-284-320-356-410-464-518F ten segments
Note: if the product is used on the table, because the bottom will produce temperature during the use process,
please use high temperature resistant flame retardant material for the table such as marble....... And so on.

56
This product does not consider the following:
Warning: If the surface is cracked, turn off the appliance to avoid possible electric
shock.
Use of equipment by unattended young children and disabled children's play
equipment.
01. Do not overheat an empty pan.
02. Do not carry the induction cooker with the appliance loaded.
03. Do not let children operate alone to avoid scalding and other risks.
04. During the operation of the appliance, the temperature of the black crystal plate
and the surface of the appliance is very high, so please do not touch it.
05. Do not use it in the bathroom, gas stove and other damp places or near inflammable
and explosive objects.
06.Metal Objects Knives, forks, spoons and LIDS should not be placed on the surface
of the cooking area to prevent them from getting hot.
07. When using the equipment, it should be placed horizontally, not close to the wall
or objects, with at least a clearance around it More than 30 cm.
08. Do not use paper, cloth and other articles on the panel to heat indirectly, so as to
avoid the high temperature of the bottom of the pot Cause combustion.
09. Do not directly add canned and other sealed containers, otherwise the container
will be heated and expanded, resulting in explosion.
10. Do not heat the aluminum foil directly or indirectly.
11. This product is a household kitchenware, shall not be used in industrial, medical
and other places to use Accident-free release.
12. Unplug the power cord plug from the socket to avoid electronic devices caused by
long time electricity Pieces of aging damage, even fire.
13. After cooking, there is still residual heat on the panel generated by the high
temperature of the pot. Do not touch it immediately.
14. If the cord is damaged, it must be repaired by the manufacturer's maintenance
department or Similar departments of professional personnel to repair and replace.
15. Do not use POTS and pans with painted bottom on the induction cooker to avoid high
temperature To burn.
16. Do not heat plastic containers and paper on panels to prevent burning.
17. Do not hit the black crystal panel with hard objects or touch the black crystal panel
with sharp instruments to avoid black crystal Plate cracking and other damage.
18. Do not use the induction cooker on the carpet or tablecloth, so as not to block the
exhaust port or suction port, shadow Heat dissipation.
19 Do not heat food directly on the panel, especially high fat food, overheating oil will
Be lit.
20. The induction cooker cannot be operated by external timer or independent remote
control system.
21. Do not place the induction cooker on the iron, stainless steel, aluminum and other
metal panel, because The action of magnetic field line will cause its heating surface to
burn out the bottom of induction cooker.
22. Do not flush with water directly to prevent the internal electronic components from
water failure.
SAFETY PRECAUTIONS

7 8

9 10
When the machine is embedded, to ensure the normal use of the machine and
better heat dissipation.
Requirements:
1. 30-50mm heat dissipation should be left on the left and right sides and behind.
2. The counter interior should be as large as possible to ensure that enough cold
air is sucked into the machine.
3. Inlet air (cold air) must be separated from outlet air (hot air) space.
4. The air inlet and outlet space of the counter leave air roar.
Positive renderings
30.00 mm 30.00 mm
left right
Induction cooker
Counter space
Heat flow
The cold air
Exhaust roar Heat flow
Exhaust roar
30.00 mm
after
Air inlet
Cupboard door
Induction cooker
Heat flow
Exhaust roar
The cold air
Counter space
Side view
HEAT DISSIPATION STRUCTURE INSTALLATION DRAWING
1515
During operation, the surface temperature of the crystal plate is very high.
Please do not touch it to avoid scalding.The appliance shall not be operated
by means of an external timer or independent remote control system.
MATTERS NEEDING ATTENTION
FAULT CODE
E0------- no pot
E1------- The voltage is lower than 90.
E2------- Excessive voltage (voltage higher than 270)
E3------- Furnace surface overtemperature or sensor damage short circuit
E4------- Furnace surface sensor open
E5-------IGBT overtemperature or fan damage does not work
E6------- The IGBT sensor is open
E8------- The control board is connected to the main power supply board
Voltage adaptation range: 90-- 270 VOLTS

11 12
POWER SUPPLY INSTALLATION DRAWING
Electrical diagram of the beautiful line (black, white, green E)
This figure is only for three-phase power in the United States, and the voltage
between two live lines is 240VAC
Three core cable machine connection drawing
2 4 0 V 4 0 A
L 1 L 2
E
L2L 1
The leakage switch
Leakage switch of power supply box
L 1 L 2
220-2 4 0 V A C
Electric ceramic oven power cord
black white green
black white green
2 2 0 V 4 0 A
LN
E
NL
The leakage switch
Leakage switch of power supply box
LN
2 2 0 V A C
Electric ceramic oven power cord
black white green
black white green
Electrical diagram of the beautiful line (black, white, green E)
This chart is only applicable to 220 V single-phase power countries in
Europe and China
Three core cable machine connection drawing
Earth wire Earth wire
Earth wire Earth wire