VEVOR SD-002 User manual

Support and E-Warranty Certificate https://www.vevor.com/support
WIRE STRIPPING MACHINE
INSTRUCTION MANUAL
We continue to be committed to providing you with tools at a competitive price. "Save Half",
"Half Price" or any other similar expressions used by us only represent an estimate of
savings you might benefit from buying certain tools with us compared to the major top brands
and do not necessarily mean to cover all categories of tools offered by us. You are kindly
reminded to verify carefully when placing an order with us if you are actually saving half
compared to the top major brands.

- 1 -
MODEL:SD-002
Have product questions? Need technical support? Please feel free to
contact us:
[e-mail]
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
WIRE STRIPPING
MACHINE

- 2 -
This is the original instruction, please read all manual instructions carefully before
operating. VEVOR reserves a clear interpretation of our user manual. The
appearance of the product shall be subject to the product you received. Please
forgive us that we won't inform you again if there are any technology or software
updates on our product.
Technical Parameter
Note: this machine is not applicable to silicone rubber cables or armored cables.
Model
Dimension
(L*W*H mm)
Weight
(kg)
Stripping Range
(mm)
SD-002
150×102×315
3.7kg
Φ1.5～Φ38

- 3 -
Parts List
1:M16 plastic nut for regulating blade up and down
2: M16 screw rod for regulating blade up and down
3: Nut for screw rod
4:Panel
5:Blade
6: Incoming panel
7:Screw for tightening incoming panel
8: Feeding hole
9:Handle

- 4 -
Accessories
Details：
1、One 4#allen key 5、Four M8 Screw nut
2、One 5# allen key 6、Four M8*35 screw
3、One 6# allen key
7、One M8*16 inner-hexagon screw、Five D8 gaskets
8、One 10#screw for connecting the electric drill

- 5 -
Operation Instruction
1.Select the appropriate feeding hole according to the wire diameter（As
shown below）.

- 6 -
2.During wire stripping, the center of the blade must be collinear with the
center of the rolling gear (as shown below).

- 7 -
3.According to the thickness of the wire, adjust the height of the blade
through the M16 screw nut above the machine so that the blade can cut
the wire skin without damaging the copper core (as shown in the following
figure).

- 8 -
4.When stripping, adjust the height of the feeding plate according to the
thickness and hardness of the wire (generally, the feeding panel should be
adjusted higher for thick and hard wires and lower for soft and thin wires).
In this way, the wire is not easy to be eccentric when stripping.

- 9 -
5.When the diameter of the wire to be treated does not exceed 20mm, the
two rolling gears need not be separated
6.When the wire diameter to be treated exceeds 20mm, the two rolling
gears need to be separated by loosening the two screws in the gears.

- 10 -
7. If the machine cannot strip the wire, there may be several reasons:
①.The diameter of the stripped wire is too small (the diameter of the wire to
be treated, including the outer skin, shall not be less than 1.5mm).
②.The blade's center is not on the same line as the rolling gear's center.
③.The blade is not sharp.

- 11 -
8.When the machine is operated by hand,install the handle (as shown in
the above figure)
Diagram of Removing Handle and Installing Electric Drill Screw

- 12 -
9.When the machine is driven by an electric drill, remove the handle first,
then install the connecting screw for the drill (do not need to add a gasket),
and use the electric drill last.
Diagram of removing the electric drill screws
10.First, assemble the handle, then hold the handle with one hand and use
the electric drill with the other hand to turn the drill counterclockwise to
remove the screw.
NOTE: Never put your hand in when the machine is running (you must stop
the machine before checking, debugging, and troubleshooting the
machine). To avoid cutting your hand,do not touch the blade directly with
your hand.

- 13 -

- 14 -
Manufacturer：
Taizhou Senduo Environmental Protection Equipment Technology Co.,
Ltd.
Address：
Workshop B14, Xiaowufen Industrial zone, Luqiao Town, Taizhou
City,Zhejiang,China
Importer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Importer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON
OXFORDSHIRE ENGLAND OX14 5DH
EUREP GmbH
Unterlettenweg 1a, 85051
Ingolstadt, Germany
REP
EC
REP
UK

Support and E-Warranty Certificate https://www.vevor.com/support