VEXO X-POT 6+ Manual

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 1
®
®
OPERATION &
MAINTENANCE MANUAL

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 2
®
®
Content
1. Safe Working Distance Statement
2. Liability
3. Warranty
4. Copyright
5. General Safety Instructions
6. Electrical Warning Symbol
7. Purpose & Use of this Manual
8. Qualications Required, Assumption
9. Appropriate Use
10. Supplied Goods
11. Transportation, Storage, Unpacking
12. Emergency Stop / Emergency Off
13. Personal Protective Equipment
14. Exceeding Permitted Pressure and/or Temperature Levels
15. Safeguards
16. External Forces
17. Electrical Equipment Inspections
18. Maintenance & Repair
19. Obvious Misuse
20. Product Description
21. Technical Data
22. Schematics & Component List
23. Operating Principles
24. Markings
25. Basic Installation Requirements
26. Critical Installation Requirements
27. Electrical
28. Commissioning
29. Control Panel
30. Monitoring & Parameters
31. MODBUS Address List
32. Filter Maintenance
33. Disassembly for Filter Replacement
34. To Clean & Replace the Filters
35. Dosing & Water Treatment Additives
36. To Manually Dose the System with Water Treatment Additives
37. Bolt Tightening Notes
38. Electrical Checks & Inspection
39. Decommissioning & Dismantling
40. General Assembly Drawing VEXO X-POT 6+
41. General Access Drawing VEXO X-POT 6+
42. Declaration of Conformity
43. Service History
.....................................................................................................................
.............................................................................................................................................................................
..........................................................................................................................................................................
........................................................................................................................................................................
....................................................................................................................................
.....................................................................................................................................
...............................................................................................................................
................................................................................................................
..........................................................................................................................................................
...........................................................................................................................................................
..................................................................................................................
.....................................................................................................................
...........................................................................................................................
...................................................................
.....................................................................................................................................................................
............................................................................................................................................................
.......................................................................................................................
...............................................................................................................................................
............................................................................................................................................................
..................................................................................................................................................
..............................................................................................................................................................
.............................................................................................................................
..................................................................................................................................................
..........................................................................................................................................................................
...........................................................................................................................
.......................................................................................................................
..........................................................................................................................................................................
.............................................................................................................................................................
................................................................................................................................................................
.........................................................................................................................................
..............................................................................................................................................
......................................................................................................................................................
..................................................................................................................
..............................................................................................................................
................................................................................................................
..........................................................
...............................................................................................................................................
.............................................................................................................................
........................................................................................................................
................................................................................................
......................................................................................................
.......................................................................................................................................
..............................................................................................................................................................
Page 03
Page 04
Page 04
Page 05
Page 05
Page 05
Page 06
Page 06
Page 06
Page 06
Page 07
Page 07
Page 07
Page 08
Page 08
Page 08
Page 08
Page 08
Page 09
Page 09
Page 09
Page 10
Page 11
Page 12
Page 13
Page 13
Page 14
Page 15
Page 17
Page 18
Page 18
Page 22
Page 22
Page 23
Page 25
Page 26
Page 29
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
WARNING – This equipment must only be used,
maintained or serviced by trained competent engineers.
If in any doubt please do not touch this equipment. For
further advice please contact VEXO International or
your reseller for additional information and guidance.
!

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 3
®
®

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 4
®
®
Liability
All technical information, data and information contained herein are correct at time of publication. This
information is the sum of our current ndings and experience to the best of our knowledge. We reserve the right
to make technical changes subject to the future development of the VEXO®product referred to in this publication.
Hence no rights may be derived from technical data, descriptions and illustrations. Technical pictures, drawings
and graphs do not necessarily correspond to the actual assemblies or parts as delivered. Drawings and pictures
are not to scale and may contain symbols for simplication.
Warranty
Active Period: 24 months from the date of commissioning.
This warranty covers manufacturing defects only.
Please note that removal of the identication data labels from the equipment will render the manufacturing
warranty null and void.
If the unit is identied with a manufacturing defect then no charge is made for correcting the defect.
The warranty is conditional upon the following clauses:
1. The equipment must be commissioned by a trained, competent engineer or qualied person, who can verify
the integrity of the equipment at that time. The qualied person must conrm in writing that the equipment is
undamaged as a result of transportation and installation and is t to begin the warranty period.
2. Photographic evidence must be collected at the time of commissioning to verify the condition of the
equipment at that time.
3. The equipment must be serviced at least annually, by a trained competent engineer or qualied person.
4. This warranty covers the equipment against manufacturing defects, normal wear and tear is not covered by
this agreement and should form part of a separate service agreement.
5. It may be anticipated that some components will become worn and be identied for change during the
warranty period, the costs associated with the required parts and associated engineer costs are not covered
by this warranty. This will be deemed as preventative maintenance and will not/does not constitute a
manufacturing defect.
6. The equipment must be stored, installed and operated in a frost free area. Damage as a result of adverse
temperature or other adverse environmental conditions will not be covered by this agreement.
7. Any and all non-warranty service visits and non-warranty inspection visits are chargeable and are not covered
by this warranty.
If a defect or problem has arisen as a direct result of the connected system, misuse, incorrect handling, incorrect
installation or incorrect commissioning then any service costs are chargeable.
If a defect is identied as a manufacturing defect it will be addressed as described above, additional remedial
works as a result of misuse, incorrect handling, incorrect installation or incorrect commissioning remain
chargeable.

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 5
®
®
Copyright
This manual must be used condentially. It may be circulated among authorised personnel only. It must not be
given to third parties. All documentation is protected by copyright. Distribution or other forms of reproduction
of documents, even extracts, exploitation or notication of the contents hereof is not permitted, unless otherwise
specied in writing by VEXO International (UK) Ltd. Infringements are liable to prosecution and payment of
compensation. We reserve the right to exercise all intellectual property rights.
General Safety Instructions
Disregard or lack of attention to the information and measures in this manual may pose a
hazard to people, animals, the environment and tangible assets. Failure to observe the safety
regulations and the neglect of other safety measures may lead to the lapse of liability for
damages in the event of damage or loss.
Denitions:
• Operator: Natural person or legal entity, who owns the product, uses it or to whom use of the product is
entrusted on the basis of a contractual agreement.
• Principal: Legally and commercially liable client in relation to the system as a whole.
• Responsible Person: The representative appointed to act by the installer or operator.
• Qualied Person (QP): Any person whose professional training, experience and recent professional activity
gives them the requisite professional knowledge. This implies that such people have knowledge derived from
relevant national and internal safety regulations.
Electrical Warning Symbol
Danger - Electric current
Disregarding these warnings may:
• Endanger health.
• Cause death, re or other damage.
• Lead to overloading of individual components and to damage.
• Impair the unit’s function.
Caution - Warning for mistakes and wrong basic assumptions
Consider the implications of errors and incorrect set-up conditions carefully!
Disregarding these warnings may lead to:
• Serious personal injury
• Overloading of individual components and damage
• Impair the unit’s function

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 6
®
®
Purpose & Use of this Manual
The following pages list the information, specications, measures and technical data that allow the relevant
personnel to use this product safely and for the intended purpose. Responsible persons or those engaged by
them carrying out the required services must read this manual attentively and understand it. Such services
include: storage, transportation, installation, electrical installation, commissioning and re-starting, operation,
maintenance, inspection, repair and dismantling.
Where the product is to be used in plants/facilities which do not comply with harmonized European regulations
and relevant technical rules and guidelines of professional associations for this eld of application, the present
document is purely for informative and reference purposes. As this unit may be subject to unlimited inspection at
all times, this manual must be kept in the immediate vicinity of the installed unit, at least within the connes of the
operations room.
Qualications Required, Assumptions
All personnel must have relevant qualications to carry out the required services, and be physically and
psychologically capable.
Operating instructions are transferred by VEXO®representatives or others assigned by them during delivery
negotiations or on demand. Training for the required services, installation, dismantling, commissioning, operation,
inspection, maintenance and repair remain the responsibility of VEXO®or their nominated service partners. Such
training covers information about on-site requirements rather than performance.
On-site requirements include logistics, manual handling, and the preparation of an installation location with the
requisite foundation engineering to accommodate the unit, and the requisite hydraulic and electrical connections,
the electrical installation for the power source of the equipment and installation of the BMS signal leads if
required.
Appropriate Use
This equipment is designed for use on sealed and un-sealed thermal systems (heating, chilled and condenser
water). It is designed to remove particulate debris from the system. The maximum operating limits of this
equipment are stated on the data labels afxed to each unit.
Supplied Goods
The items delivered must be compared against the items listed on the shipping note and inspected for conformity.
Unpacking, installation and commissioning may be started only once the product has been checked as
conforming with the intended use. In particular, exceeding the permissible operating or design parameters may
lead to malfunctioning, component damage and personal injury.
If not in line with conformity statement or if the delivery is incorrect in any other way, the product must not be
used.

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 7
®
®
Transportation, Storage & Unpacking
The equipment is delivered in packing units in conformity with contract specications or specications required
for the distributors method and climate zone.
They meet the requirements of the distributors packaging guidelines as a bare minimum. In conformity with these
guidelines, equipment is shipped horizontally, each unit packed on reusable pallets. These pallets are suitable for
horizontal transportation with approved fork-lift trucks.
The forks must be set to the widest possible outer dimensions in order to prevent the load from tipping over.
When moving the equipment in question, the forks must be in the lowest possible position, with the article at
right angles to the forks. If the packages are suitable for lifting gear, they will be marked at the appropriate lifting
points.
Important note: Transport the packed goods as close as possible to the envisaged set-up location and make sure
there is a vertical, solid surface on which the goods can be mounted / secured.
Caution:
Please take precautions to make sure the equipment, once it has been removed from the pallet and the
packaging, does not impact any other equipment or surface, tip over or rock.
Once it has been removed from the pallet and the packaging, the equipment must be transferred in a safe
manner. Use methods that prevent uncontrolled falling, sliding or tipping over.
The equipment may also be warehoused in their packaging. Once it has been removed from its packaging, the
equipment must be put in position, observing standard safety procedures. Do not stack the equipment. Use only
permitted lifting gear and safe tools, and wear the required personal protective equipment.
Emergency Stop / Emergency Off
In line with directive 2006/42/EC required EMERGENCY-STOP facility is made available by the main power switch
on the iX-2, refer to the VEXO® X-POT 6+® Schematic, item 24 on page 10 of this document.
Personal Protective Equipment (PPE)
PPE must be used when carrying out potentially dangerous work and other activities, in order to prevent or
minimize the risk of personal injury if other measures cannot be taken.
These must comply with the requirements referred by the main contractor or operator of the plant room or the
site in question. If no requirements are set, to operate the equipment minimum requirements are safety goggles,
hand protection, well-tting clothing and sturdy, closed and skid-proof footwear.
Exceeding Permitted Pressure &/Or Temperature Levels
Equipment used in combination with the VEXO® X-POT 6+®must guarantee that the permitted operating
temperature and the permitted medium temperature (heat transfer medium) cannot be exceeded. Excess
pressure and temperature may lead to component overload, irreparable damage to components, loss of
function and, as a result, to severe personal injury and damage to property. Regular checks/inspections of these
safeguards must be carried out.

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 8
®
®
Safeguards
The equipment supplied is equipped with the required safety devices. To test their effectiveness or restore the
original set-up conditions, the equipment must rst be taken out of service. Taking the system out of service
implies that power should be isolated, hydraulics isolated and then vented.
External Forces
Avoid any additional forces (e.g. forces caused by heat expansion, vibration or dead weights on the ow and
return lines).
These can lead to damage / leakage in water-bearing pipework, loss of stability of the appliance and potentially
failure of pressure bearing components.
Electrical Equipment Inspections
Regardless of the prescriptions of the property insurer / operator it is recommended to inspect demonstrably the
electrical equipment of the VEXO® X-POT 6+®together with the heating or chilled installation at least every 12
months.
Maintenance & Repair
These services may only be carried out when the X-POT 6+® is shut down. The VEXO® X-POT 6+® equipment
must be taken out of service and guarded against unintentional re-starting until the maintenance work is nished.
The control panel can be interconnected to a MODBUS RS485 (BMS) or alarm system to allow for indication that
the lter is ready for change and the magnets are ready for cleaning.
The VEXO®PD-Monitor® is tted with a combined visual illuminated ashing beacon in low light situations for
visual indication and sounder as an indication of lter blockage.
The unit must be inspected on an annual basis, and the electrical and mechanical components veried for
operation and integrity (See inspection table below).
Task
Visual inspection of components 6 Months - Qualied Person
Operational check of hydraulic
components
12 Months - Annual Service - Qualied
Person
Operational check of electrical
components
12 Months - Annual Service - Qualied
Person
VEXO®X-POT 6+®

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 9
®
®
Obvious Misuse
• Operation at incorrect voltage and/or frequency.
• Use in inappropriate system designs and environments.
• Use of non-permitted or inappropriate installation materials.
Product Description
The VEXO® X-POT 6+® is a sealed system, 2 stage side stream ltration and manual
chemical dosing unit.
It is a Patented, fully prefabricated, factory tested wall mounted unit incorporating:
• Grundfos 3-Speed Single Speed circulating pump, (Pump to be set at CP2)
• VEXO®PD-Monitor® (MODBUS RS485 BMS Connectivity)
• Magnetic Filtration
• Cartridge Filter Filtration
• Air Separation
• Dirt Separation
• Manual Dosing facility
• Working Pressure up to 10Bar
• Working temperature from O°C up to 95°C
Technical Data
Unit
Model
Unit
Model
Flow Rate
(l/s)
Maximum
System Size
(litres) Width
(mm)
Grundfos Reference Motor Rating Electrical Supply Current
Depth
(mm)
Height
(mm)
Dry Weight
(KG)
Wet Weight
(KG)
Dimensions
Circulating Pump
VEXO®
X-POT 6+
VEXO®
X-POT 6+
1.0 86,400 340
Grundfos UPMXL 25-125
976
180W
46
230/1/50
58
~1.42 Amps
850

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 10
®
®
Schematics & Component List
PT
PT
CLEAN
RETURN
DIRTY
FLOW
System Return
SCHEMATIC
01
02
03
04
05
06
07
08
0910
11
12
13
14
15
16
17
18
01
02
03
04
05
06
07
09
10
11
12
13
14
15
16
17
08
18
ISOLATING VALVE DRAIN VALVE
CHEMICAL FILL TUNDISH
VEXO®X-POT 6+® VESSEL BODY ISOLATING VALVE
SWING CHECK VALVE
BAFFLE PLATE (INTERNAL) AUTOMATIC AIR VENT
CARTRIDGE FILTER (INTERNAL) MANUAL VENT ISOLATION VALVE
PD-MONITOR®
GRUNDFOS UPMXL 25-125 MAINS ON/OFF POWER SWITCH
ISOLATING VALVE MODBUS RS485 BMS
PRESSURE TRANSDUCER 1
(DIRTY FLOW)
MAGNET GRATE (INTERNAL)
CONTAINING 6 MAGNETS
PRESSURE TRANSDUCER 2
(CLEAN RETURN)

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 11
®
®
Operating Principles
The VEXO® X-POT 6+® is designed to be a self-contained ltration equipment, with a dedicated inlet and outlet
connection to a sealed and open vented system. The system uid passes through the hydraulic components in the
ow sequence below:
The system uid is drawn from the main system return and into the VEXO® X-POT 6+® vessel. The uid is drawn
through a twin stage ltration system, in the rst chamber, ferrous particulates are captured by the rare earth
magnets contained in the magnet grate, the uid then passes through the Bafe Plate and into the second
chamber, where non-ferrous particulates are captured by the cartridge lter before the sampled water
exits the VEXO® X-POT 6+® vessel, it then passes through the Side Stream Filtration Pump and back to the main
system return.
The VEXO® X-POT 6+® is provided with a manual dosing facility comprising of a tundish, isolation valve and swing
check valve arrangement. The equipment is also provided with an automatic air vent for the release of free air
within the VEXO® X-POT 6+®assembly.
The equipment is provided with a proprietary VEXO® iX-2 controller, with VEXO® control methodology, that
monitors the pressure drop across the VEXO® X-POT 6+® ‘Filters’ to determine the status of the lter media and
to trigger the on-site cleaning and replacement of the lter media as appropriate.
FLUID FLOW DIRECTION
Isolating Valve
SCHEMATIC REFERENCE No. (Page 10)
Pressure Transducer (Dirty Flow) in Vessel
Pressure Transducer 2 (Clean Return)
Side Stream Filtration Pump
Isolating Valve
Magnetic Grate & Magnets
Baffle Plate
Cartridge Filter
VEXO™
X-POT 6+
10L
VESSEL
No. 01
No. 02
No. 07
No. 08
No. 09
04
05
06
No. 03
HYDRAULIC COMPONENTS CHART
DIRTY FLOWCLEAN RETURN

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 12
®
®
Product Markings
THE FOLLOWING MARKINGS AND WARNINGS ARE INSTALLED ON THE X-POT 6+ UNIT
Approved by:
Contact your X-POT 6+
representative for info.
Recommended
for use with
this product
And more!
®®
INTEGRATED ELECTRONIC SIDE STREAM FILTRATION & DOSING UNIT

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 13
®
®
Installation
Basic Installation Instructions
The equipment is to be connected from/to the return header pipework of the appropriate sealed system. The
maximum pipe run length from the system pipework to the VEXO® X-POT 6+® is to be 10m.The 2 connections,
from/to the return pipework, for the VEXO® X-POT 6+®is to be made at the bottom / underside of the return
pipework to allow for any dense particulate solids to be drawn into the VEXO® X-POT 6+®for active removal from
the system. A 1” drain with isolation valve is supplied at the bottom of the vessel. Extend this drain to a local oor
gully with a minimum fall of 1:100.
The Power supply to the VEXO® X-POT 6+®is to be provided from the main system pump electrical supply.
Therefore, the VEXO® X-POT 6+®will only be activated when the main system pump is running and active. Ensure
the power supply is 230V ~ 1N PE 50Hz via a suitable Fused Spur and Isolator.
It is essential to ensure the environment that this equipment is installed in is safe to work and is free from trip
hazards.
Critical Installation Requirements
The equipment must be sited:
• In a frost free area (> 5°C) and must also be protected from adverse environmental conditions.
• In a well-lit area to allow for safe changing of the lter media and chemical dosing.
• On a at, vertical, level, solid wall with access to the electrical panel, pump and VEXO® X-POT 6+®vessel itself.
Care must be taken when handling this equipment. Appropriate safety measures must be in place in respect of
use, handling and application of:
• Electrical equipment
• Pressure vessels
• Sealed system water
• Powerful rare earth magnets
• Filter media
• Hydraulic equipment
• Manual handling
• Chemical inhibitors and additives
• Particulate debris

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 14
®
®
Electrical Connections & Wiring Diagram

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 15
®
®
Commissioning
1. General
The VEXO® X-POT 6+® is a ‘Plug and Play’ unit. It is supplied factory set with the Grundfos UPMXL 25-125 Pump
set to ‘CP2’ and the Differential Pressure across the Filter Vessel set to 0.4 Bar.
The operator should read this section prior to hand-over of the equipment from the installation operative to be
condent on the operation of the VEXO® iX-2 Controller and the VEXO® X-POT 6+®unit as a whole.
The Control System is based around a VEXO® iX-2 Controller complete with |/O modules.
A Display Panel is tted to the VEXO® iX-2 Controller to allow interrogation and adjustment of the parameters.
In the event of a power failure, the VEXO® iX-2 Controller will return to its factory set operating mode once power
has been restored.
The Power supply to the VEXO® X-POT 6+® is provided from the main system pump electrical supply. Therefore,
the VEXO® X-POT 6+®will only be activated when the main system pumps are running and active.
Ensure the power supply to the VEXO®X-POT 6+®is 230V ~ 1N PE 5OHz via a suitable Fused Spur.
The power supply is then connected to the main VEXO® X-POT 6+® Mains Isolation Switch, refer to the unit
schematic, item 17 on page 10 (Schematic) of this document.
The power is then distributed throughout the VEXO® X-POT 6+®via an internal wiring loom.
WARNING
This equipment must only be used, maintained or
serviced by trained competent
engineers. If in any doubt please do not touch this
equipment.
For further advice please contact VEXO International
(UK) Ltd or your reseller for additional information
and guidance.
WARNING
This equipment uses Rare Earth Magnets with a
strong magnetic eld.
You should not use, service or work in the close
vicinity (30cm / 1ft) of this equipment if you are
tted with a pacemaker or other electromechanical
medical devices.

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 16
®
®
2. Enable Filtering
It is important to visually inspect the electrical connections, components and conduit serving the VEXO®
X-POT 6+®unit before commencement of the operation of the unit. It is important to visually inspect the
VEXO®X-POT 6+® unit hydronic connections before commencement of the operation of the unit to conrm the
following;
The integrity of all ttings and pipework connecting the heating / chilled system to the VEXO® X-POT 6+®-
Ensure there are no leaks.
• The closure lid of the VEXO® X-POT 6+®is closed and sealed tight in accordance with the ‘Bolt Tightening’
method in Section 4 (page 27) of this document.
• All isolating valves ‘as supplied’ used to drain the VEXO® X-POT 6+®are closed with the valve handles at
90° to the pipework they are connected to. Refer to page 10 for the VEXO® X-POT 6+® Schematic, valve
references 10 & 15.
• All isolating valves ‘as supplied’ which connect the VEXO® X-POT 6+®to the main heating / chilled system
should be in the ‘open’ position. Rotate the valve handles to be in-line with the pipework it is connected to.
Refer to page 10 for the VEXO® X-POT 6+® Schematic, valve references 1 & 9.
• When the VEXO® X-POT 6+® has been lled with system water and pressurised, check the hydronic integrity
of all ttings and pipework within the VEXO® X-POT 6+® unit - Ensure there are no leaks. To conrm the
VEXO® X-POT 6+® has been lled, check the iX-2 Controller is displaying a pressure reading.
• Any system air will be drawn out through the Automatic Air Vent, item (14). This is a normal procedure.
2.1. Circulation Pump
The Circulation Pump (item 08) installed onto this VEXO® X-POT 6+® is a ‘Grundfos UPMXL 25-125’. The pump
needs to be set at CP2 for the VEXO® X-POT 6+®to operate correctly.
2.2. Activation
The VEXO® X-POT 6+®can be activated by turning the Isolator Switch from the ‘Off’ position to the ‘On’ position.
The VEXO® iX-2 Controller will now scroll the following...
< >
FILTER PUMP RUN
FILT

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 17
®
®
3. Enable Filtering
The Differential Pressure is factory set to 0.4 Bar. To reset the parameters (for example, the pressure
differential) the following sequence needs to be followed on the VEXO®iX-2 Controller. See list of parameters
on previous page:
• Press and hold “Set” button 4 to access parameters
• Enter code “815” and then while holding set press the up or down button to access required parameter.
• Change the parameter setting using up or down
• Press and hold set to save required setting, the controller will scroll “Saving” and return to main screen.
4. Fault Messages
If a fault is detected, the VEXO® iX-2 Controller display will scroll a Fault Message as below. The VEXO® iX-2
Controller will also initiate the visual strobe and sounder to draw attention to the user.
Fault
Message
Blocked
Filter
Isolate the X-POT 6+® & change lters to allow the
X-POT 6+ to operate
Shutdown
Shutdown
Shutdown
Shutdown
Sensor 1
Fail
Call Engineer to check connections and replacement
of the Pressure Transducer
Sensor 2
Fail
Pump
Fail
Call Engineer to check connections and replacement
of the Pressure Transducer
Call Engineer to check connections and replacement
of the Pump
X-POT 6+®
Operation Solution
RUN
Button 1 Button 3
Button 2 Button 4

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 18
®
®
VEXO®iX-2 Controller Monitoring
VEXO®iX-2 Controller Parameters
0
1
2
3
4
5
6
Pressure Differential
Alarm Relay Contacts
Sensor Minimum Pressure
Sensor Maximum Pressure
Current Sense
Bar - PSI
Buzzer Enable
0.4 Bar
0
0 Bar
30 Bar
N
Bar
Y
0.0 - 1.0 Bar
0 = N/C 1 = N/C
0.0 - 10.0 Bar
0.0 - 10.0 Bar
Y/N
Bar/PSI
Y/N
Number Parameter Default Value Range
Volt free contacts are provided for the following conditions. The contacts are rated 5 amp, 230v maximum.
Filter On - In Normal Operation, the VEXO® iX-2 Controller will scroll “Filter
Pump Run”.
In the event the lter is blocked, the VEXO® iX-2 Controller will scroll “Blocked
Filter”
- Filter Blocked, Clean Magnet Grate / Replace Filters.
In the event of a Dirty Flow Pressure Transducer failure, the VEXO® iX-2
Controller will scroll “Sensor 1 Fail”.
- Pressure Transducer Dirty Flow Failure.
In the event of a Clean Return Pressure Transducer failure, the VEXO® iX-2
Controller will scroll “Sensor 2 Fail”.
- Pressure Transducer Clean Return Failure.
In the event the X-POT 6+® Circulating Pump fails to operate, the VEXO® iX-2
Controller will scroll “Pump Fail”.
- Flow Pump Failure.
FILT
BLOC
SEN
SEN
PUM
< >
FILTER PUMP RUN
< >
BLOCKED FILTER
< >
SENSOR 1 FAIL
< >
SENSOR 2 FAIL
< >
PUMP FAIL
The display rolls:
The display rolls:
The display rolls:
The display rolls:
The display rolls:

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 19
®
®
VEXO®iX-2 Controller Parameters
Preliminary Settings
7
8
9
10
Pressure Differential Message
Baud Rate 9600
Continues on following page...
Word Length 8
Parity NO
Stop Bits 1
ID Numbers
Pump Hours
Alarm Count
1
0
-
-
1. Blocked Filter
2. PHX High DP
- Service now
3. High DP on Coil
- Service Now
4. High DP on Strainer
- Service Now
5. High DP
- Service Now
0 = N/C 1 = N/C
-
-
Number Parameter Default Value Range
MODBUS Address List

www.VEXOint.com
[e-mail]
[phone]
X-POT 6+®O&M Manual
Last Updated - 11/01/2023
Page 20
®
®
X Variable
Address
40001
40002
40003
40006
40007
40008
40009
40013
40014
40015
40016
40023
40024
40025
40026
40027
40028
40029
40030
40031
40032
40033
Pressure Sensor 1
Pressure Sensor 2
Current
Pump Relay
Filter Pump Alarm Relay
General Alarm Relay
Buzzer
Filter Blocked Alarm
Pump Failure Alarm
Sensor 1 Alarm
Sensor 2 Alarm
Par. Pressure Diff
Par. Alarm Relay Contact
Par. Minimum Pressure
Par. Maximum Pressure
Par. Current Sense
Par. Bar/PSI Unit
Par. Buzzer Enable
Par. Pressure Diff. Message
Par. ID Number
Par. Pump Hours
Par. Alarm Counter
Read
Read
Read
Read
Read
Read
Read
Read
Read
Read
Read
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Value of Sensor 1
Value of Sensor 2
Value of current through pump
Status of Pump Relay
Status of Pump Relay
Status of General Alarm Relay
Status of Buzzer
Status of Filter Blocked Alarm
Status of Pump Failure Alarm
Status of Sensor 1 Alarm
Status of Sensor 2 Alarm
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Value of Parameter
Denomination Type X Variable
Format Description
Continues on following page...