Viatek UOF3-MC01-AS20KM User manual
Board Diagram
Installation Steps
Please check the following items before installation. If any missing, please contact the
dealer.
Fast Media Converter 1pc
Power Adapter 1pc
1pc
User Manual
1) Please turn off the power related to the device before installation;
2) Please check if the network cables being taken up by other device;
3) Please connect LAN port of Converter and NVR or network device like computer with
network cable;
4) Use a optical fibers with single-mode one fiber connect with fiber port of two
Converters;
5) Please check if the installation is correct and power the system;
6) Please check if the network is working.
Installation
It is fast ethernet fiber optic transmission equipment which can converter between two
different network cable and optical fiber transmission medium. Support 100Mbps network
bandwidth. This product can be used in pair and also can be used with other equipment. It is
widely used in surveillance, home network fiber, etc.
Feature
Provide 100Mbps 1 fiber optic port and 1 Ethernet port which can converter between
10/100BASE-TX and 100BASE-FX;
Compatibility with IEEE 802.3u 100BASE-TX/FX;
Support 10/100Mbps full/half duplex automatic adaptation, support
automatic MDI/MDIX.
Fast Media Converter
12
Fast Media Converter
LED Indicator Instruction：
Application
Leftside
Rightside
Optical Fiber
Ethernet Switch
Optical Fiber
Fast Media Converter
Ethernet Switch
Power Input Copper Port
Fiber PortPower&Fiber
LED Indicator
LED
Function
Status
Instruction
PWR
Power
On
Power on
Off
Power off
FX
Fiber Port Signal Detection
On
Fiber signal receive well
Off
No fiber signal input
Link/Act
Fiber Port Connection Status
On
Fiber port connect well
Flicker
Connect well, with data transmission
Off
Fiber port without connect
100M
Ethernet Port Rate
On
1000M
Off
100M
Link/Act
Ethernet Port Connection Status
On
Ethernet port connect well
Flicker
Connect well, with data transmission
Off
Ethernet port without connect
FDX/COL
Ethernet Port Full Duplex
On
Full Duplex
Off
Half Duplex
single mode single fiber SC 20km
A: Transmitter 1310/1550nm B:Receiver 1550/1310nm
Fast Media Converter
Specification
连接接口
Item
Description
Power
Power Supply
Power Adapter
Power Voltage
DC5V
Consumption
＜5W
Ethernet Port
Ethernet Port
LAN Port: 100Mbps
Transmission Distance
LAN Port: 0～100m
Fiber Port
Fiber Port
single mode single fiber SC 20km
A: Transmitter 1310/1550nm B:Receiver
1550/1310nm
Bandwidth
155Mbps
Transmission Distance
20km
Network
Standard
Compatible with
IEEE802.3, IEEE802.3u10/100BASE-TX and
100BASE-FX
LED Status
Indicator
Power
1 Green
Ethernet
3 Green (1000M, Link/Act, FDX/COL)
Fiber
2 Green (Link/Act, FX)
Protection
ESD
1a Contact Discharge 3
1b Air Discharge 3
Per IEC61000-4-2
Lightning Protection
Power: 2KV
Signal: 1KV
Per: IEC61000-4-5
Environmental
Working Temperature
0 ~55℃℃
Storage Temperature
-40 ~70℃℃
Humidity (non-condensing)
0~95%
Mechanical
Dimension (L×W×H)
26mm×71mm×94mm
Material
Aluminum Alloy
Color
Black
Weight
160g
Stability
MTBF
>30000h
连接接口
Trouble Shooting
Please find the following solution when the device doesn't work
Please confirm if the installation is correct;
Please confirm if the RJ45 cable order in accordance with the EIA/TIA568A or 568B
industry standards;
The maximum transmission distance is depend on the signal source and cable quality,
please do not over the maximum transmission distance;
Please replace a normal device with a failure one to check if the device is broken;
If the problem still exist, please contact the factory.
Product are subject to change without prior notice
34
Instruments to be used: wire crimper, network tester.
Wire sequence of RJ45 plug should conform with EIA/TIA568A or 568B.
1) Shuck off about 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2) Depart the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Brunt cut the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6)Then use wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Using network tester to test the cable whether is working.
RJ 45 Making Method
Make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
pin color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
pin color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A EIA/TIA 568B
Notice
Fast Media Converter
Fast Media Converter
