Vicon V9360 User manual

www.vicon-security.com
XX263-20-01
V9360 Indoor
Network Hemispheric Camera
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.
Vicon Industries Inc., 89 Arkay Drive, Hauppauge, New York 11788
Tel: [phone] Fax: [phone] Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
Document Number: 8009-8263-20-01
Product specications subject to change without notice.
Issued: 613
Copyright © 2013 Vicon Industries Inc. All rights reserved.
Installation Guide

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Table of Contents
Precautions 3
1. Introduction 6
Package Contents.............................................................................6
Features and Benefits .......................... Error! Bookmark not defined.
Safety Instructions ............................... Error! Bookmark not defined.
Physical Description ........................................................................7
2. Accessing Camera 11
If you have DHCP server router in your network:........................ 11
If you do NOT have DHCP server/router in your network:.......... 11
2

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Precautions
Read these instructions
Read all the safety and operating instructions before using this product.
Heed all warnings
Adhere to all the warnings on the product and in the instruction manual. Failure to follow the
safety instruction given may directly endanger people, cause damage to the system or to other
equipment.
Servicing
Do not attempt to service this video device yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual may be registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class Adigital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
This device is likely to be damaged or damage other equipments/personnel, if you use a power
supply with different voltage than the one included with this device. All warranty of this product
will be voided if this occurs.
Don’t open the housing of the product
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
4

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Damage Requiring Service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged.
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
Caution: The black base of the camera will be hot while camera is powered on!
(Please note that this is a NORMAL CONDITION for this model since the base is used as a
heat sink and all the camera functions will work normally!)
Caution: Do NOT install this camera directly onto any surface (wall,
ceiling). One of the mounting accessories must be used, V9360-WM
wall mount or V9360-FMK in-ceiling flush mount.
5

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
1.Introduction
Package Contents
V9360 H.264 4-Megapixel IP D/N Hemispheric
Camera with Advanced WDR QIG
Terminal Blocks for Power, DI/O Network Cable
Audio Accessories
Drill Template
6

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Physical Description
Reset Button Ethernet Port
Micro SDHC Card Slot Digital Input/Output
Power LED 12 VDC Power Input
Audio Input/Output
1) Reset Button
Step 1: Switch off IP device by disconnecting the power cable.
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen).
Step 3: Reconnect the power cable while continuing to hold the Reset Button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for
another second and turn off again. By this time the reset to default operation is already
completed. This will take about 20 seconds from power up (this length of time fluctuates
slightly with the environment). You may then release the Reset Button. The Power LED light
will come back on and stay on after a few more seconds. The unit will start up with factory
default settings automatically.
On (3s) On
1s
Power On
About 20 Seconds
Stay On
Off (about 15s) Off (10~15s)
Restore to Default
Complete
7

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
2) Micro SDHC Card Slot*
Insert a Micro SDHC card (*customer supplied) for local recording on camera.
3) Power LED
This LED light will indicate current camera status.
4) Audio Input/Output (Indoor unit only)
The IP device supports audio input and output via terminal block
Audio terminal block
Red
Green
Audio In/Out
Audio In
Audio Out
5) Ethernet Port
The IP device connects to the Ethernet via a standard RJ-45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
6) Digital Input/Output
Used in applications like motion detection, event triggering, time lapse recording, alarm
notifications, etc., the I/O terminal connector provides the interface to:
•Digital Output (2) - For connecting external devices such as relays and LEDs. Connected
devices can be activated by Output buttons on the Live View page or through video
management software. Connect Pin 2 with Pin 4 or Pin 6 with Pin 8.
•Digital Input (2)- An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The device
will detect the change in digital input and transmit the signal to video surveillance servers.
Digital Input/Output Connector
8

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Pin 1 GND
Ground. Connect with Pin 3 for DI control loop.
Pin 2 12 V
Provides power to external devices with a
maximum current of 100 mA.
Voltage: 12 VDC,
Max: 1.2 W
Pin 3 Digital Input 1
Connect to GND (Pin 1) to activate or leave
floating (unconnected) to deactivate.
Must not be exposed
to voltages greater
than 30 VDC.
Pin 4 Digital
Output 1
Connect to Pin 2 through external devices for
DO loop. If used with an external relay, a diode
must be connected in parallel with the load for
protection against transient voltages.
Max load = <100 mA
Max voltage = 24 VDC
(to the transistor)
Pin 5 GND
Ground. Connect with Pin 7 for DI control loop.
Pin 6 12 V
Provides power to external devices with a
maximum current of 100 mA.
Voltage: 12 VDC,
Max: 1.2 W
Pin 7 Digital Input 2
Connect to GND (Pin 5) to activate or leave
floating (unconnected) to deactivate.
Must not be exposed
to voltages greater
than 30 VDC.
Pin 8 Digital
Output 2
Connect to Pin 6 through external devices for
DO loop. If used with an external relay, a diode
must be connected in parallel with the load for
protection against transient voltages.
Max load = <100 mA
Max voltage = 24 VDC
(to the transistor)
Connect input/output devices to the camera as follows:
1. Attach the cables for the device securely to the supplied green connector block.
2. Once cables are connected, push connector block into the terminal connector on camera.
7) 12 VDC Power Input
Connect DC power source to the terminal block. The wire with white dashed lines is the live
wire, which should connect to the 12V pin.
Once cables are connected, push the terminal block into the 12 VDC power input terminal
connector of the camera.
PIN NAME DESCRIPTION
1 E-Ground Chassis Ground
2 GND DC Power Input
3 12 V
9

V9360 Hemispheric Camera with Advanced WDR
Hardware User’s Manual
Using the Mounting Options
V9360-WM Wall Mount
If it is required to mount the V9360 to a wall, use the V9360-WM. Typical mounting hardware is
provided; be sure to use mounting hardware appropriate for the mounting surface.
1. A mounting template is provided with the wall mount. Mark the mounting holes on the
surface and drill mounting holes. Mount the flat side of the V9360-WM to the wall, with
the wide end (with the cable hole) at the top, using appropriate hardware for the
surface; be sure to use anchors as needed. Cables can be routed through the back
slot or through the access hole.
2. Remove the camera cover if not already done. Align the three (3) holes on the bottom
of the V9360 with the mounting posts of the V9360-WM. Secure with the screws
provided. Reattach the cover.
V9360-FMK Wall Mount
If it is required to mount the V9360 flush in the ceiling, the V9360-FMK is required.
1. Carefully snap the trim ring off of the in-ceiling mounting assembly.
2. Using the template provided, cut a hole in the ceiling for the V9360-FMK.
3. Lift the in-ceiling mount assembly up through the ceiling hole so that the mounting lips
rest on the ceiling. Tighten the flipper screws until the mounting assembly is securely
in place. Holes are provided in the lip if additional support is required.
4. Remove the camera cover. Align the three (3) mounting holes on the bottom of the
camera with the mounting posts on the mounting assembly. Secure the camera with
the screws provided.
5. Snap the trim ring back onto the mounting assembly.
10