Vicon VC-700W User manual

VC-700W and VC-700WC
COLOR DOME CAMERAS
About this manual
INSTRUCTION MANUAL XX178-10
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for later reference.
This installation should be made by a qualified service person and should conform
to the National Electric Code, ANSI/NFPA 70 and all local codes.
Installers should use appropriate hardware mounting materials.

This equipment generates and uses radio frequency energy and if not installed
and used properly, that is, in strict accordance with the manufacturer’s instruction,
may cause interference to radio and television reception. It has been type tested
and found to comply with the limits for a Class A computing device in accordance
with the specification in subpart B of part 15 of the FCC rules, which are designed
to provide reasonable protection against such interference in a commercial
installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and
television reception, which can be determined by turning equipment off and on,
the user is encouraged to try and correct the interference by one or more of the
following measures:
FCC Notice
Note: Complies with Federal Communications Commission Rules & Regulations
Part 15, Subpart B for a Class A digital device.
WARNING
• Reorient the receiving antenna.
• Relocate the equipment with respect to the receiver.
• Relocate the equipment away from the receiver.
• Plug the equipment into a different electrical outlet so that the equipment
and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions.

Warning: Power must be removed from this unit before removing circuit
modules or cables.
Caution: This unit contains circuit cards with integrated circuit devices that
can be damaged by static discharge. Take all necessary precautions
to prevent static discharge.
The user may find the following booklet prepared by the Federal Communications
Commission helpful:
“Interference Handbook, Bulletin CIB-2”
This booklet is available from the U.S. Government Printing Office, Superintendent
of Documents, Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.

Surface-Mount configuration In-Ceiling configuration
Dimensions : inch (mm)

PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and installation, as it may be
dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. This could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong shock or
vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler room,
as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened
with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to support the camera.

TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your service center.
■If no image appears
▪Is the coaxial cable attached securely?
▪Are the power and voltage normal?
▪Has the iris of the lens inside the camera been adjusted correctly
(with the level volume) ?
▪Is there adequate illumination?
■If the image is unclear
▪Is the lens in focus?
▪Is the lens dirty?
▪Dirt or fingerprints on the lens can adversely affect the images.
Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens
cleaning paper and cleaning fluid (commercially available).
▪Is the monitor adjusted correctly?

LENS ADJUSTMENT
1. Adjust the panning (360˚) and tilt (90˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws (using small M1.0 Hex L-wrench provided) to adjust roll
(turns camera position top/bottom).
PAN ROLL SET
SCREW
(2X)
TILT
90˚ZOOM
FOCUS

SPECIFICATION - VC-700W/C SERIES
General Spec NTSC PAL
HQ Interline Transf er CCD 1/3" 410K Pixels Color 1/3" 470k Pixels Color
Total Number of Pixels 811(H) X 508 (V) 795(H) X 596(V)
Scanning System 525 Lines 625 Lines
Hor iz ontal Res olution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/A E
AWB
AGC
Electrical Spec
Operating Voltage
Pow er Consumption
Mechanical Spec
Opertion Temp
Air Humidity
Lens
Connections via
12VDC(11-20V), 24VAC(20-27V)
12VDC - 2.2W, 24VAC - 1.95W
0.45
550TV Lines
> 48dB [AGC off]
Internal / External (Line Lock)
0.04fc, 0.4Lux(Scene) With F1.2 Lens
Up to max.90%
3.3-12mm or 9-22mm
14°F ~ 131°F (-10°C ~ +55°C)
1.0Vp-p/75ohm Composite
BNC(V IDEO) , 2P WIRE(POWER)
DIP Sw itc h Selec t ON/OFF
DIP Sw itc h Selec t ON/OFF
DIP Sw it c h S ele c t ME/ A E ( ON/OFF)
DIPSw itch Select ATW/AWB (ON/OFF)

SPECIFICATION - VC-700W-IR/C SERIES
General Spec NTSC PAL
HQ Interline Transf er CCD 1/3" 410K Pixels Color 1/3" 470k Pixels Color
Total Number of Pixels 811(H) X 508 (V) 795(H) X 596(V)
Scanning System 525 Lines 625 Lines
Hor iz ontal Res olution
Sensitivity to Light [30IRE]
IR Dis tanc e
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/A E
ATW/AWB
AGC
Electrical Spec
Operating Voltage
Pow er Consumption
Mechanical Spec
Opertion Temp
Air Humidity
Lens
Connections via BNC(VIDEO), 2P WIRE(POWER)
14°F ~ 131°F (-10°C ~ +55°C)
Up to max.90%
3.3-12mm
DIP Sw itc h Selec t ON/OFF
12VDC(11-20V), 24VAC(20-27V)
MAX LED ON (12VDC - 4.1W, 24VAC - 4.7W)
DIP Sw itc h Selec t ON/OFF
DIP Sw it c h Sele c t ME/ A E ( ON/OFF)
DIPSw itch Select ATW/AWB (ON/OFF)
0.45
> 48dB [AGC off]
Internal(12VDC) / External (Line Lock, 24VAC)
1.0Vp-p/75ohm Composite
550TV Lines
20m range
BW, NO LED : 0.004fc, 0.04Lux(Scene) With F1.2 Lens
COLOR : 0.04fc, 0.4Lux(Scene) With F1.2 Lens

SPECIFICATION - VC-700WDN/C SERIES
General Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470k Pixels Color
Total Number of Pixels 811(H) X 508 (V) 795(H) X 596(V)
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
Control DIP Switch
BLC
ME/A E
ATW/AWB
AGC
Electrical Spec
Operating Voltage
Pow er Consumption
Mechanical Spec
Opertion Temp
Air Humidity
Lens
Connections via
Up to max.90%
3.3-12mm or 9-22mm
BNC( V IDEO), 2P WIRE( POWER)
BW : 0.004fc, 0.04Lux(Scene) With F1.2 Lens
12VDC(11-20V), 24VAC(20-27V)
12VDC - 2.3W, 24VAC - 2.6W
14°F ~ 131°F (-10°C ~ +55°C)
DIP Sw itch Select ME/AE (ON/OFF)
DIP Sw itch Select ATW/A WB (ON/OFF)
Internal(12VDC) / External (Line Lock, 24VAC)
1.0Vp-p/75ohm Composite
DIP Sw itch Select ON/OFF
550TV Lines
Color : 0.04fc, 0.4Lux(Scene) With F1.2 Lens
0.45
> 48dB [AGC off]
DIP Sw itch Select ON/OFF