Vicon VC-700WDR User manual

VC-700WDR
COLOR DOME CAMERAS
About this manual
INSTRUCTION MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for later reference.
This installation should be made by a qualified service person and should conform to the
National Electric Code, ANSI/NFPA 70 and all local codes.
Installers should use appropriate hardware mounting materials.

Surface-Mount configuration In-Ceiling configuration
Dimensions : inch (mm)

PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and installation, as it may be
dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. This could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong shock or
vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler room,
as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth moistened
with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to support the camera.

TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your service center.
■If no image appears
▪Is the coaxial cable attached securely?
▪Are the power and voltage normal?
▪Has the iris of the lens inside the camera been adjusted correctly
(with the level volume) ?
▪Is there adequate illumination?
■If the image is unclear
▪Is the lens in focus?
▪Is the lens dirty?
▪Dirt or fingerprints on the lens can adversely affect the images.
Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens
cleaning paper and cleaning fluid (commercially available).
▪Is the monitor adjusted correctly?

LENS ADJUSTMENT
1. Adjust the panning (360˚) and tilt (90˚) position.
2. Set the zoom position by using Zoom Lever Screw.
3. Set the focus by using Focus Lever Screw.
4. Loosen set screws (using small M1.0 Hex L-wrench provided) to adjust roll
(turns camera position top/bottom).
PAN SET
SCREW
(2X)
TILT
90˚ZOOM
FOCUS

SPECIFICATION
General Spec NTSC PAL
CCDType
Total number of pixels
Min illumination
Video Output
Resolution
S/N Ratio
Gamma
Wide Dynamic Range 102dB(typical), 120dB(max)
Shutter Speed 1/60s - 1/100,000s 1/50s - 1/100,000s
SyncSystem
White Balance
Power Input
Video Output
Voltage
Power Consumption
Lens
Operation Temp
Operation humidity
3.3-12mm or 9-22mm
14°F ∼131°F (- 10℃∼+55℃)
48dB or more(AGC of f)
0.45
Up to 90％(non-condensing)
Connectors
Wire
BNC Cable
ElectricSpec
12VDC(10 - 16V) or 24VAC
2.0W
Mechanical Spec
Internal (12VDC) / External (Line Lock, 24VAC)
Auto , manual
1/3" PIXIM CMOS progressive
742(H) X 552 (V)
0.06fc(0.6Lux) F1.2, 30IRE at COLOR
0.008fc(0.08Lux) F1.2, 30IRE at BW(TDN)
1.0Vp-p/75 ohm Composite
540 TV Lines

CONNECTIONS
12VDC-24VAC
12VDC-24VAC
RED (+)
BLACK (-)
11.8in
(300mm
)
RED (+)
BLACK (-)
VIDEO
VIDEO

CAUTION
The use of a UL Listed Class 2 power supply is required to ensure compliance with
electrical safety standards.
Check for polarity when using a 12VDC power supply.
Cable for connection to portable monitor, provided.
When using a portable monitor, terminate at 75ohms (at last device).

Surface-Mount Base In-Ceiling Base

■CAMERA SETTINGS
CAMERA SETTINGS