Vicon VC600 User manual

COLOR DOME CAMERAS
About this manual
Dimensions : inch (mm)
INSTRUCTION MANUAL XX166-00
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for future reference.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below.
If the problem persists after checking these items, contact
your service center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
SPECIFICATIONS
■Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause fire, short-circuits or
damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen
or boiler room, as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it
with a soft cloth moistened with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to
support the camera.
PRECAUTIONS
VC600, VC600C, VC610 and VC610C
General Spec NTSC PAL
HQ Interline Transfer CCD 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total Number of Pixels 811[H] x 508[V] 795[H] x 596[V]
Scanning System 525 Lines 625 Lines
Horizontal Resolution
Sensitivity to Light [30IRE]
Gamma Correction
Shutter Speed 1/60 - 1/100,000[NTSC] 1/50 - 1/100,000[PAL]
S/N Ratio
Synchronization
Video Output
BLC
ME/AE
ATW/AWB
AGC
Operating Voltage
Consumption
Operating Temperature
Air Humidity
Lens Mount
Connections via
Dimensions(Diam x H)
Control DIP Switch
Electrical Spec
Mechanical Spec
550TV Line
1.0Vp-p/75 ohm Composite
Internal / External
> 48dB [AGC off]
0.45
0.3Lux(Scene) With F1.2 Lens
DIP Switch Select ON/OFF
DIP Switch Select ON/OFF
DIP Switch Select ATW/AWB (ON/OFF)
DIP Switch Select ME/AE (ON/OFF)
DC12V 2.5[W], AC24V 2.0[W]
DC12V (DC11.0V~20.0V), AC24V(20.0V ~27.0V)
14˚F - 131˚F (-10˚C - +55˚C)
4.5 X 4.1 inch ( 114.4[Φ] x 103[mm])
BNC(VIDEO), 2P WIRE(POWER)
DV 3.3 ~ 12mm (M14)
Up to max. 90%

■CONNECTIONS
■CAMERA SETTING
S
■LENS ADJUSTMENT
S
CAUTION
Check for polarity when using a DC 12V or AC 24V power supply.
1. Adjust the panning(360˚) and tilt(60˚) position.
2. Setting the zoom position by using Zoom Lever Screw.
3. Setting the focus by using Focus Lever Screw.
360˚ 360˚
60˚ 60˚
Zoom
Focus
Focus
CONNECTIONS AND CAMERA SETTINGS
Red (+)
Black (-)
DC12V
AC24V
VIDEO
●Compensating for backlight 1 ●Setting gain control (AGC) 4
ON When back light is too bright For adjusting the sensitivity of the camera.
OFF Normal setting Use this setting for shooting in dark environments.
CAUTION : It will be correctly set by adjusting level volume 5. ON Normal Setting
OFF Set this when there is excessive noice
●Confirming the iris setting 2
ME(ON) When DC auto-iris lens is installed ●Adjusting level volume 5
AE(OFF) When fixed iris lens is installed If the entire image is too dark or bright, or the backlight
compensation is not correct, you need to adjust the level volume.
CCW(LOW) Closes the lens iris, making the entire image darker
CW(HIGH) Opens the lens iris, making the entire image brighter
●White balance setting 3
ATW(ON) Use this under light source below 2500K and over 9500K of natrium.
AWB(OFF) Use this under light source between 2500K and 9500K of fluorescent
lamp, incandescent light
NO. FUNCTION
1BLCOFFON
2 AE/ME AE ME
3 ATW/AWB AWB ATW
4 AGC MAX OFF ON
DIP S/W

INSTALLATION - Surface / In-ceiling Mounting Dual-Use
Brussels Office
Planet II - Unit E
Leuvensesteenweg 542
B-1930 Zaventem
Belgium
[phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com
1 Use the philips screwdriver to remove the screw (C).
2 Separate upper case (A) from bottom case (D).
3 Cut a hole (diameter:2.9inch/73mm) in the ceiling for
routing the cables.
4 Align the extension ring with the surface of the ceiling;
make marks on the ceiling in the places where the
screw holes are to be drilled, and then drill the four
holes.
5 Pass the power cable (I) and video cable (H) from the
camera unit through the cable hole in the ceiling.
6 Align the four screw holes in the extension ring (G)
with the screw holes in the ceiling, and then secure
the camera in place by tightening four screws (F)
supplied with the unit.
7 Fixing mounting extension ring(G) on bottom case (D)
by using screw(B).
8 Carry out the settings and adjustments to the camera.
9 Adjust the dome liner (E) so that the dome camera's
lens is visible from the camera window and then
use a philips screwdriver to attach the dome cover.
10 Connect upper case (A) and bottom case (D)
11 Tighten the screw (C).
Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
USA
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
European Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
44(0) 1489 566300
Fax: [phone]
Vicon Part number 8009-8166-00-00 Rev705
IH
G
F
D
C
A
BE