Vicon Matrix 44 V4410S-1 User manual

X783-20-00 Rev 904 Matrix 44 Video Switch Card & Associated Components •1
The V4410S-1 video switch card can accommodate up to 8 video inputs per card. Each card
cage can accommodate up to 16 V14410S-HD cards, for 128 inputs by 8 outputs. Associated
components identified in this document include rear panels V4411RP-BNC and V4411RP-RIB,
terminators V75T-1 and V75TR-1, and coaxial ribbon cables V44RC-21-1 and V44RCB-12-1.
Warning: Disconnect power from all units. The Matrix 44 card cage power switch can be
accessed by loosening the four captive screws on the front panel of the card cage.
Do not apply power until all procedures are complete and all connections made.
Setting DIP Switches
1. Using a static-free work surface, loosen the captive screws on the front panel of the Matrix 44
card cage containing the expander card.
2. The video switch cards are located at the extreme left of the card cage, as viewed from the
front of the card cage. Locate DIP switch U7 on the video switch card.
3. Set the DIP switch on each card, using the following table. Reseat the cards in the cage and
tighten the captive screws to secure the front panel when finished.
V4410S-HD DIP Switch U7 Pole Settings
Cameras 1 2 3 4 5
1-8 OFF OFF OFF OFF OFF
9-16 ON OFF OFF OFF OFF
17-24 OFF ON OFF OFF OFF
25-32 ON ON OFF OFF OFF
33-40 OFF OFF ON OFF OFF
41-48 ON OFF ON OFF OFF
49-56 OFF ON ON OFF OFF
57-64 ON ON ON OFF OFF
65-72 OFF OFF OFF ON OFF
73-80 ON OFF OFF ON OFF
81-88 OFF ON OFF ON OFF
89-96 ON ON OFF ON OFF
97-104 OFF OFF ON ON OFF
105-112 ON OFF ON ON OFF
113-120 OFF ON ON ON OFF
121-128 ON ON ON ON OFF
129-136 OFF OFF OFF OFF ON
137-144 ON OFF OFF OFF ON
145-152 OFF ON OFF OFF ON
153-160 ON ON OFF OFF ON
161-168 OFF OFF ON OFF ON
169-176 ON OFF ON OFF ON
177-184 OFF ON ON OFF ON
185-192 ON ON ON OFF ON
193-200 OFF OFF OFF ON ON
201-208 ON OFF OFF ON ON
209-216 OFF ON OFF ON ON
217-224 ON ON OFF ON ON
225-232 OFF OFF ON ON ON
233-240 ON OFF ON ON ON
241-248 OFF ON ON ON ON
249-256 ON ON ON ON ON
NOTES NO. REV. SEC.
Refer to X783 X783-20-00 904 2
Matrix 44®Video Switch
Card & Associated
Components

2 •Matrix 44 Video Switch Card & Associated Components X783-20-00 Rev 904
Camera Connections and Looping Video to Switcher Card Cages
1. In systems with more than one card cage, loop video from one cage to the next using ribbon
cables V44RC-21-1 or V44RCB-12-1 as shown in the following figure. Rear panels
V4411RP-BNC (top card cage) and V4411RP-RIB (bottom two card cages) are shown.
2. Connect cameras as shown by the labels shown in the figure.
3. Terminate any unused connectors using V75TR-1 or V75T-1.
J1
J2
Video input
from camera 1
Video input
from camera 8
Looping video (cameras 1-8) to next card cage.
Terminate if not used to loop out to another card cage.
Looping video
(cameras 1-8) to
third card cage
Looping video
(cameras 1-8) to
second card cage
J1
J2
J1
J2
Copyright © 2004 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Vicon part number 8006-8783-20-00 Section 2 Rev 904
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)