VIDEOMAN VS-747, VS-747M, VS-747C, VS-747PS User manual

VS-747 Kit VS-747M
Inc. VS-747M, VS-747C,VS-747PS Inc. VS-747M, VS-747PS
VIDEMAN is a registered trade mark of EOS Australia Pty Ltd
Designed, imported and distributed by Videoman Systems Co.
VS-747
FEATURES
■15 DIFFERENT RINGTONE
■UP TO 4 MONITORS, 4 OUTDOOR STATIONS AND 4 AUDIO
HANDSETS
■INTERCOMMUNICATION IN BETWEEN HANDSETS

-Page 1 –
Indoor monitor VS-747M installation guide
Install the indoor monitors about 1.55M ~ 1.60M from
the floor.
VS-747C Door station installation guide
Surface mount with optional VS-747C
4B3Y2W1R LB
1
2
3
155 Cm
Fig. 3
Flush mount with optional VS-747CS
Fig. 4
160 Cm
130mm
200mm
175mm
70mm
100mm
Ref. No: VS-902EB
Install the door stations about 1.55M ~ 1.60M from the
ground.
Keep the units away from snow, rain and direct sunlight.
Fig 1 Fig 3
Fig 2

-Page2 -
Description of monitor VS-747M features
Dimensions ： 166(W)×210(H)×49(D) mm
1. Microphone
2. Blue LED
3. TALK Button
4. CALL Button
5. UNLOCK Button
6. MONITOR Button
7. FUNCTION Button
8. LED for Door Release
9. LED for IN-use
10. Speaker
11. B&w CRT Screen
12. Image adjustment
13. Talk volume adjustment
14. Ring volume adjustment
15. Wiring Terminals
16. Mounting Blacket Hold
Fig 4
Dimension: 166(W) x 210(H) x 49(D) mm

Descriptions of Door Station VS-747 C features
3
5
4
2
2W1R 3Y 4B LB 8
7
6
Dimension: 128(H)x98(W)x43(D)
1
Fig. 9
4B3Y2W1R LB
1
2
3Common - Black
N.O. - Red
N.C. - White
1R +12V DC presents when outdoor station being called or
supervised.
2W Ground (GND)
3Y Video signal (1Vp-p)
4B Audio and control signal
1. Camera
2. IR LEDs for night vision
3. Speaker
4. CALL button
5. Microphone
6. Cable terminal to monitor
7. Unlock port LB – The characteristic of this
port out is determined by JP-LK Jumper
on back of monitor (Refer to Page2 #15,
Page6 Note1,2,3)
With Jumper : Additional power
supply is not required for door latch
Without Jumper : Additional power
supply is not required for door latch
Pin#1 (Top - Red): Normally Open
Pin#2 (Middle-Black): Common
Pin#3 (Bottom-White ): Normally Close
8. Mounting bracket
Descriptions of Stainless Steel Flush mount Door Station
Overall Dimension (mm):
200(H)x130(W)x50(D)
Cut Out size without embedding box:
100(W) x 130(H) x 60(D)
Cut Out size with embedding box:
175(H)x100(W)x70(D)
LA 2W1R 3Y 4B LB
3
5
4
2
1
Fig. 10
1. Camera
2. IR LEDs for night vision
3. Speaker
4. Call button
5. Microphone
NOTE : This camera can be used with optional
embedding box (Ref.VS-902EB), Refer to Page1.
-Page 3 -
Fig 5
Fig 6

Descriptions of Multi Door Switcher VS-4 way-Optional Extra
Cameras Installed
VT-MDS
DS1,2
DS1,2,3
DS1,2,3,4
JW/VP
DS1
DS2
DS3
DS4
Refer to Fig.15 on Page7
JW/VP terminal
1R,2W,3Y,4B: Connect to Monitor(s)
DS1 terminal
1R,2W,3Y,4B: Connect to Door Station #1
DS2 terminal
1R,2W,3Y,4B: Connect to Door Station #2
DS3 terminal
1R,2W,3Y,4B: Connect to Door Station #3
DS4 terminal
1R,2W,3Y,4B: Connect to Door Station #4
SET switch
Set switch to select quantity of extended Door
Stations or Cameras
Video distributor GL-D4L-PLUS for multiple monitors
When more than two monitors are installed in a system, it is highly recommended to use a video amplifier GL-D4L-PLUS
for better image.
Descriptions of Audio Handset
Dimensions ： 215(H)×80(W)×45(D)
1. Intercom Button
2. Unlock Button
3. Handset
4. Handset Curve
Descriptions of Power supply
16VDC 1.0A Power supply
( + ) : White Broken Line : + DC 16V
( – ) : Black wire : Ground
Fig 7
Fig 8
Fig 9
Fig 10
JP1
In order to employ the output (Out)
of the video distributor,remove the
jumper terminal( JP1 ) on the PCB
to V on Monitor #4
to V on Monitor #3
to V on Monitor #2
to V on Monitor #1
Video IN
G(Ground) wires
from Door Station & Monitors
MUST connect to
this GND terminals.
GL-D4L-PLUS (Optional Extra)
(+) (-)
CTin Gnd CTout
SE-12VDC05Adpt (Optional Extra)
+ -
D1 D2 In Out D3 D4
75 ¥Ø
8
When GL-D4L-PLUS is used,
the termination DIP switches shall set to
75ohm on all monitors.
-Page 4-
Ω
VS-4WAY

•
-Page5 –
Operation Instructions
■ Operation for basic Video Outdoor Station
1) When visitor presses the Call Button on the Outdoor Station, the monitor rings, at the same
time, the screen displays the visitor’s image, and Blue LED flashes.
2) When you press the TALK Button, you can talk with the visitor for 90 seconds, During the talk
state, press TALK Button again to end the conversation. If nobody answers the phone, the
screen will turn off within 30 seconds automatically. If the system connects two or more
Monitors, and while any Monitor starts to talk, the other Monitors will automatically shut off.
3) When Monitor is on standby, press MONITOR Button, the screen will display the view of the
Outdoor Station. During monitoring state, press TALK Button, you can speak to the Outdoor
Station, or press MONITOR again to turn off. However, monitoring state is limited to 30
seconds and will be shut off automatically.
4) Press ULOCK Button to release the Electronic Latch during monitoring or talking.
5) Image quality can be adjusted by means of Contrast and Brightness rheostats.
6) The ring and talk volume can be adjusted individually.
■ Operation for intercom
1) When system is connected with multi Monitors, intercom is available.
2) Intercom calling can be initiated by any Monitor. Press CALL button, IN USE led will lighten,
and other Monitors will ring. If TALK Button is pressed in another Monitor, the intercom talking
is connecting.
3) In calling state, press TALK Button to cancel, or it will exit automatically after 30 seconds if no
answers.
4) Intercom function is prior to monitor function, but calling function is always first.
■ Operation for ring selection
1) When Monitor is standby, press FUNC Button and hold for 2 seconds to enter Chord melody
selection state and the current melody will be played.
2) Press FUNC Button again to switch to next chord melody sequentially, one more time Chord
Select Button is pressed, next melody is switched and played.
3) Press TALK Button to confirm melody selection; press MONITOR/UNLOCK/CALL Button to
exit without saving the change.
4) The monitor will exit automatically if no operation within 30 seconds.
■ Operation for multi Outdoor Stations or Cameras (Only if VT-MDS is installed)
1) When a Outdoor Station calls, Monitor image and talk will be switched automatically.
2) All Monitors can survey each Outdoor Station in turn. Press MONITOR Button in standby, the
image of 1st Door Station is displayed firstly, press TALK to talk; If press MONITOR one more
time, the image will switch to next Outdoor Station, etc. After monitoring the last image, press
MONITOR will exit, or shut off within 30 seconds.
3) During monitoring or talking state, press UNLOCK Button will just open the lock connected
with the being supervised Outdoor Station.

IMPORTANT!! Please read page 8 & 9 for cable requirements BEFORE running cable
System connection with one camera, one monitor and one audio phone
Electronic Latch connecting
With Jumper (Dry contact mode).
1
2
3POWER
SUPPLY
Dry contact mode
Without Jumper (DC output for latch mode)
3
2
1
DC output mode
-Page 6 -
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
Red
White
BlackBlack
White
Red
+12
2W
4B
JS-AP
JP-LK
3Y
4B
2W
1R
AC ~
BACK
OUTDOOR STATION
1
2
3POWER
SUPPLY
MONITOR
OUTDOOR STATION
Note1 Note3
Note 2
zNote 1: JP-VD is used for setting
the video impedance. When there is
only one Monitor, keep the jumper
(which is already on JP-VD ). But
when multi Monitors are installed,
be sure of taking away all JP-VD of
Monitors except only the last
Monitor.
zNote 2: LB includes 3 wiring
Terminals: ‘1’-Normally Opened
Terminal, ‘2’- Common Terminal,
‘3’- Normally Closed Terminal. If the
latch is activated when powering,
connect it between ‘1’ and ‘2’
terminal; if the latch is deactivated
when powering, connect it between
‘2’ and ‘3’ terminal.
zNote 3: JP-LK is used for Latch
selection, refer to Electronic Latch
connecting parts .
Extra power supply for latch must be installed, and
nearly all kinds of electronic latch can be used,
please see Note 2 for reference. Incidentally, in this
mode, you can continue talking and monitoring
during unlock operation.
The Latch can directly connect with the Outdoor
Station and the power through monitor. During
unlock operation, the monitor will close screen
automatically. The Latch is rated voltage is 12V,
less than 500mA consumption.
Note: Please use right and specific Latch.
Fig 11
Fi
g
12
Fig 13

IMPORTANT!! Please read page 9 & 10 for cable requirements BEFORE running cable
System connection with one camera and 4 monitors
-Page 7 -
Fig 14
OUTDOOR
STATION
AC ~ AC ~
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
3Y
4B
2W
1R
AC ~
MONITOR
1 # MONITOR
4 #
JP-VD Removed!
AC ~
MONITOR
2 #
AC ~
MONITOR
3 #
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
3Y
4B
2W
1R
AC ~
JP-VD Removed!
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
3Y
4B
2W
1R
AC ~
JP-VD Removed!
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
3Y
4B
2W
1R
AC ~
JP-VD Reserved!

IMPORTANT!! Please read page 9 & 10 for cable requirements BEFORE running cable
System connection with 4 camera and one monitor
-Page 8
Fig 15
BACK
OUTDOOR
STATION No.2
1
2
3
3
2
1
OUTDOOR
STATION No.1
BACK
POWER
SUPPLY
POWER
SUPPLY
JP/LKJP/VD
JS-VP
+12
2W
4B
DC+
DC
DC-IN
JS-AP
3Y
4B
2W
1R
Cameras Installed
VT-MDS
DS1,2
DS1,2,3
DS1,2,3,4
JW/VP
DS1
DS2
DS3
DS4
MONITOR
BACK
OUTDOOR
STATION No.4
1
2
3POWER
SUPPLY
BACK
OUTDOOR
STATION No.3
1
2
3POWER
SUPPLY

NOTE
Fig 8 : 2Core 24/020 ( = 2Core 0.75mm2 )
Junction room : electrical switch room, junction room,
ceiling
Cable requirement –STAR Wiring method
-Page 9 -
An additional power supply and Fig8
Cable is required for door strike
operation (Indicated as broken lines
on the diagrams)
Cable requirement
Based on the distance from a camera to the
furthest monitor,
< 20M : CAT5 cable
A (Audio)
G (GND)
V (Video)
G (GND)
B (12VDC)
B (12VDC)
double up
DO 1
DO 2
(door open)
Orange
W/Orange
Green
W/Green
Blue
W/Blue
Brown
W/Brown
CAT5 wire configuration
< 50M :
14/020 (0.44mm2)shielded cable
(connect shield to G)
AND
RG-59/U for video signal
(connect core to V & shield to G)
< 100M :
24/020 (0.44mm2)shielded cable
(connect shield to G)
AND
RG-59/U for video signal
(connect core to V & shield to G)
> 100M :Contact your supplier
Fig 16
Fig 17
Fi
g
18
Power Supply
for door latch Power Supply
VS-747PS
Fig 8 4 core
Screened
VS-747C
CAMERA VS-747M
MONITOR
Fig 8
Fig 8
4 core
Screened
Junction Room
Power Supply
for door latch Power Supply
VS-747PS
Junction Room
VS-747C
CAMERA
Fig 8
Fig 8
4 core
Screened
Fig 8 4 core
Screened
VS-747M
MONITOR VS-747M
MONITOR
4 core
Screened
Fig 8
Power Supply
VS-747PS
Junction Room
Fig 8 4 core
Screened
VS-747M
MONITOR VS-747M
MONITOR
4 core
Screened
Fig 8
Fig 8
VS-747C
CAMERA
Fig 8
4 core
Screened
Fig 8
Fig 8
Fail-Secure
Door Strike
Fail-Secure
Door Strike
Fail-Secure
Door Strike
INUSE
VS-4W AY
4CamerasSwitcher
4 way switch
D1 D2 In Out D3 D4
CTin Gnd CTout
+ - GL-D4L-PLUS
JP1
D1 D2 In Out D3 D4
CTin Gnd CTout
+ - GL-D4L-PLUS
JP1
Power Supply
for door latch
4B-Audio
3Y-Video
1R-12DC
2W-GND
2W-GND
1R-12DC

Cable requirement – Daisy Chain (loop-in-loop-out) wiring method
-Page 10 -
Power Supply
for door latch Power Supply
VS-747PS
Fig 8
VS-747C
CAMERA VS-747M
MONITOR
Fig 8
Fig 8
4 core
Screened
Junction Room
Power Supply
for door latch Power Supply
VS-747PS
Junction Room
VS-747C
CAMERA
Fig 8
Fig 8
4 core
Screened
Fig 8
4 core
Screened
VS-747M
MONITOR VS-747M
MONITOR
Fig 8
Power Supply
VS-747PS
Junction Room
Fig 8 4 core
Screened
VS-747M
MONITOR VS-747M
MONITOR
4 core
Screened
Fig 8
Fig 8
VS-747C
CAMERA
Fig 8
4 core
Screened
Fig 8
Fig 8
Fail-Secure
Door Strike
Fail-Secure
Door Strike
Fail-Secure
Door Strike
INUSE
VS-4W AY
4CamerasSwitcher 4 way switch
NOTE :
Fig 8 : 2Core 24/020 ( = 2Core of 0.75mm2 )
Junction room : electrical switch room, junction room, ceiling
MEMO
Fig 19
Fig 20
Fig 21

MAINTENANCE
1. All components should be protected from violent vibration, impacting, knocking and dropping.
2. If necessary, clean the lens and screen with dampen soft cotton cloth do not use chemical cleaning agent.
3. Image distortion may occur if the monitor is installed near microwave ovens, TVs, computers, DC/AC adaptors or any other electro
magnetic field generating appliances.
4. Keep all monitors and cameras away from high temperature, dust, caustic and oxidation gas.
5. Use only with the VS-747PS power supply which is supplied by the authorised VIDEOMAN supplier.
6. Pay attention to the high voltage inside the products. Please ensure this unit is only serviced by qualified professionals.
TECHNICAL SPECIFICATIONS
1. Talk auto-off time: 90 seconds
2. Surveillance auto-off time: 30 seconds
3. Power supply for indoor monitor : DC 15~18V (supplied by Adaptor)
4. Power for Door Station: DC 10~12V (Supplied by Indoor Monitor)
5. Power consumption: Standby 0.5W; Working status 15W (for kits)
6. Monitor screen: 4 Inch B&W CRT,
7. Camera Lens: 3.6mm, 72 degree horizontal visual angle
8. Resolution: >300 TV lines
9. Video signal: 1Vp-p, 75Ω, CCIR standard
10. Connection mode: 4 wire, polarity conscious
11. Door strike operation : Voltage-free Relay output from the Door Station
12. Door strike operation time : controlled by Door button on Monitor
WARRANTY STATEMENT
This equipment is warranted to be free from defects in material and workmanship for a period of twelve months from the date of purchase as indicated on
the proof of purchase and/or by serial number on the product.
Defective units returned by the purchaser at his own expense during this period will be repaired (or replaced at the option of the distributor) with an
equivalent piece of refurbished and tested equipment. The repaired or replaced equipment is then warranted for the balance of the initial warranty period or
for thirty (30) days, whichever is longer.
The repair or replacement will be without charge provided that the equipment has not been subjected to electrical of physical misuse or to unauthorised
repair or modification.
The foregoing warranty is in lieu of all other warranties, express or implied, including, but not limited to, merchantability or fitness for a particular purpose.
The purchaser's exclusive remedy with respect to any and all losses or damages resulting from any cause whatsoever, shall be repair or replacement as
specified above.
Distributor shall in no event be liable for any consequential or incidental damages, however occasioned, whether by negligence or otherwise. No suit or
action shall be brought against manufacturer more than one year after the accrual of the cause of action therefore. No agent, employee or representative of
the distributor nor any other person is authorised to modify this warranty in any respect. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
www.eos.com.au