Videoquip Phase 3 SD-2 User manual

SD-2
Silence Detector
Videoquip Research Limited
595 Middlefield Road, Unit #4
Scarborough, Ontario, Canada
M1V 3S2
www.videoquip.com

Introduction
The Phase 3 SD-2 silence detector is a professional audio level monitoring device,
specifically designed to detect silence, or the absence of audio.
Two completely independent channels of detection monitor the two balanced audio
inputs. Each channel has an indicator for the presence of active audio, an adjustable
silence level, and an adjustable delay before silence notification occurs. Gold relay
contacts for each channel allow external devices to be controlled, or may be used to
route active audio for emergency backup audio switching.
The balanced audio connectors are of the XLR type, and the relay connectors are
screw clamp terminal blocks. The SD-2/R rackmount version contains either 1 or 2
SD-2 modules. These modules are identical to the SD-2 version, which is described
throughout this manual.
Installation
The SD-2 consists of 2 completely independent monitoring networks.
Each of the 2 channels provides a female XLR connector for balanced audio input, and
screw clamp terminal blocks for the relay outputs.
Audio Inputs
The audio sources to be monitored are connected to the SD-2 input channels (A,B).
Connect balanced signals as shown in Table 1.
Pin # Function
1Ground
2+
3-
Table 1. XLR Input Connector Pinout
For unbalanced signals, connect the signal to pin 2 (+), and the shield to ground. It is
not necessary to ground pin 3 (-) when using unbalanced signals.
Relay Outputs
Any external devices or audio signals to be controlled by the relays are connected to
the terminal blocks. Two full form-C gold relay contacts are available for each channel,
allowing balanced stereo signals to be controlled. The connections for each relay (from
left to right) are Common, Normally Open (N.O.), and Normally Closed (N.C.). These
are clearly silkscreened on the rear panel.
The normally closed (N.C.) and normally open (N.O.) relay conditions for each channel
exist when audio is present at the channel input (the green signal LED is lit), and
during the adjustable transition delay before a silence alarm occurs (no LEDs lit). The
contacts switch when silence is indicated by the red silence LED for corresponding
channel.

Make connections to the relays between either N.O. and Common or N.C. and
Common, depending on the equipment being connected.

Installation (cont'd.)
Audible Alarm
The audible alarm sounds with the occurrence of each new silence condition,
regardless of which channel it occurs on. The audible alarm may be silenced after each
occurrence using the front panel Mute Alarm switch, or may be permanently disabled
by unplugging and opening the unit, and moving the Alarm jumper to the OFF position.
Adjustment
The front panel Level and Delay controls determine the reference audio levels for
silence detection and the delay times before the silence alarms are activated.
The SD-2 is adjusted before leaving the factory for silence levels of -20 dBm, and the
minimum delay time (1 second). The silence threshold levels may be adjusted between
-40 and 0 dBm, and the delay times from 1 second to 50 seconds using the front panel
controls.

SD-2 Specifications
Power Requirements 115 VAC, 60 Hz or 230 VAC, 50 Hz; 6 W
Audio Inputs
Number of Inputs 1 per channel, 2 channels total
Input Impedance 40 kohms balanced
Input Connectors XLR, female
Common Mode Rejection -85 dB @ 60 Hz
Silence Detection
Silence Level -40 dBm to 0 dBm
Detection Delay 1 second to 50 seconds
Silence Indicator LED, red
Silence Alarm Piezo, 4 kHz
Relay Contacts Gold, form-C, 2 per channel
Relay Connectors Screw clamp terminal blocks
Audio Signal Indicator LED, green
Physical Dimensions (Inches)
SD-2 8.1 W x 1.9 H x 5.1 D
SD-2/R 19 W x 1.75 H x 5.0 D
Warranty
Videoquip Research Limited (VRL) warrants the Phase 3 SD-2 for a period of 2 (two)
years from the date of shipment from the factory, to be free of defects in workmanship
and material under normal use and service. This warranty is void if failure is due to
abnormal use or modification, or if serial numbers have been tampered with. VRL's
liability is limited to the repair or replacement of this unit, or to a sales credit, and the
warranty action taken is at the discretion of VRL. Any warranty claims must be received
in writing by VRL before the expiration of the two year period. Warranty coverage does
not include shipping costs. This warranty is in lieu of all other warranties, expressed or
implied, and all other obligations or liabilities of Videoquip Research Limited.