Viessmann Vitodens 200-W System User manual

Start-up/Service Instructions
for use by heating contractor
Vitodens 200-W, WB2B Series
Models WB2B 19, 26, 35
Wall-mounted, gas-fired condensing oiler
For natural gas and liquid propane
Heating input 31 to 126 MBH
9 to 37 kW
VITODENS 200-W 

Read and save these instructions
for future reference.
IMPORTA T
This trademark is registered with the U.S. Patent and Trademark Office.
5418 911 v1.0 2 08/2009
Please file in Service Binder

Safety, Installation and Warranty Requirements
2
Safety, Installation and Warranty Requirements
Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the
instructions listed elow and details printed in this manual can cause product/property damage,severe personal injury, and/or loss
of life. Ensure all requirements elow are understood and fulfilled (including detailed information found in manual su sections).
HLicensed professional heating
contractor
The installation, service, and
maintenance of this equipment must
be performed y a licensed
professional heating contractor.
"
Please see section
entitled “Important
Regulatory and
Installation
Requirements” in the
Installation Instructions.
HProduct documentation
Read all applicable documentation
efore commencing installation. Store
documentation near oiler in a readily
accessi le location for reference in
the future y service personnel.
"
For a listing of
applicable literature,
please see section
entitled “Important
Regulatory and
Installation Requirements”
in the Installation Instructions.
HCarbon monoxide
Improper installation, service and/or
maintenance can cause flue products
to flow into living space. Flue
products contain poisonous car on
monoxide gas.
"
For information
pertaining to the proper
installation, service and
maintenance of this
equipment to avoid
formation of carbon monoxide, please
see the Installation Instructions of the
Vitodens 00 Direct Vent System.
HEquipment venting
Never operate oiler without an
installed venting system. An improper
venting system can cause car on
monoxide poisoning.
HWarranty
Information contained in
this and related product
documentation must e
read and followed. Failure
to do so renders warranty
null and void.
HAdvice to owner
Once the installation work is
complete, the heating contractor
must familiarize the system
operator/ultimate owner with all
equipment, as well as safety
precautions/requirements, shut-down
procedure, and the need for
professional service annually efore
the heating season egins.
Warning
This oiler requires fresh air for safe operation and must e installed with provisions for adequate com ustion and
ventilation air (in accordance with local codes and regulations of authorities having jurisdiction).
Do not operate this oiler in areas with contaminated com ustion air. High levels of contaminants such as dust, lint or
chemicals can e found at construction sites, home renovations, in garages, workshops, in dry cleaning/laundry facilities,
near swimming pools and in manufacturing facilities.
Contaminated com ustion air will damage the oiler and may lead to su stantial property damage, severe personal injury
and/or loss of life. Ensure oiler/ urner is inspected and serviced y a qualified heating contractor at least once a year in
accordance with the Start-up/Service Instructions of the oiler.
Operating and Service Documentation
It is recommended that all product documentation such as parts lists, operating and service instructions e handed over to
the system user for storage. Documentation is to e stored near oiler in a readily accessi le location for reference y
service personnel.
5418 911 2
Installers must follow local
regulations with respect to
installation of carbon monoxide
detectors. Follow manufacturer’s
maintenance schedule of boiler.
WAR I G

Index
3
Page
General Information
Safety, Installation and Warranty Requirements 2 ...................................
Operating and Service Documentation 2 ......................................................
Important Regulatory and Installation Requirements 5 ...........................
About these Start-up/Service Instructions 8 ................................................
ecessary Tools 8 ...................................................................................................
Applicability 9 ............................................................................................................
Product Information 9 ............................................................................................
Mechanical Room 10 .................................................................................................
Removing Front Enclosure Panel 11 ...................................................................
Initial Start-up
and Service
Procedure (Overview) 12 ........................................................................................
Steps 14 ........................................................................................................................
Control Technology
Outdoor Reset Programming Unit (Vitotronic 200, HO1) 28 ..................
Coding
Coding Level 1 39 .....................................................................................................
Coding Level 2 42 .....................................................................................................
Service Scans
Service Level Overview 52 .....................................................................................
Temperatures, Boiler Coding Card and Brief Scans 53 .............................
Checking Outputs (Relay Test) 54 ......................................................................
Scanning Operating Conditions and Sensors 55 ...........................................
5418 911 2

4
Troubleshooting
Diagnostics 56 .............................................................................................................
Corrective Action 62 ................................................................................................
Additional Information
Control Functions 66 .................................................................................................
Wiring Diagrams 69 ..................................................................................................
Parts Lists 71 ...............................................................................................................
Maintenance Record 74 ..........................................................................................
Technical Data 75 ......................................................................................................
Lighting and Operating Instructions 77 .............................................................

General Information
5
Important Regulatory and Installation Requirements
Codes
The installation of this unit shall e in
accordance with local codes or, in the
a sence of local codes, use
CAN/CSA-B149.1 or .2 Installation
Codes for Gas Burning Appliances for
Canada. For U.S. installations use the
National Fuel Gas Code ANSI Z223.1.
Always use latest editions of codes.
In Canada all electrical wiring is to e
done in accordance with the latest
edition of CSA C22.1 Part 1 and/or
local codes. In the U.S. use the
National Electrical Code ANSI/NFPA
70. The heating contractor must also
comply with oth the Standard for
Controls and Safety Devices for
Automatically Fired Boilers,
ANSI/ASME CSD-1, and the Installation
Code for Hydronic Heating Systems,
CSA B214-01, where required y the
authority having jurisdiction.
Instructing the system user
The installer of the system is
responsi le to ensure the system
operator/ultimate owner is made
familiar with the system functioning,
its activation, and its shut-down.
Initial start-up
Initial start-up must e performed y a
qualified heating contractor. Proper
completion of the Maintenance Record
y the heating contractor is also
required.
Working on the equipment
The installation, adjustment, service,
and maintenance of this oiler must e
done y a licensed professional heating
contractor who is qualified and
experienced in the installation, service,
and maintenance of hot water oilers.
There are no user serviceable parts on
the boiler, burners, or control.
The following topics must be
covered:
Proper system operation sequence.
Explain the equipment.
Demonstrate an emergency
shut-down, what to do and what not.
Explain that there is no substitute for
proper maintenance to help ensure
safe operation.
The Maintenance Record is located
on page 74 of this manual.
Please carefully read this manual prior
to attempting start-up, maintenance
or service. Any warranty is null and
void if these instructions are not
followed.
For information regarding other
Viessmann System Technology
componentry, please reference
documentation of the respective
product.
We offer frequent installation and
service seminars to familiarize our
partners with our products. Please
inquire.
Ensure main power supply to
equipment, the heating system, and all
external controls has een deactivated.
Close main gas supply valve. Take
precautions in all instances to avoid
accidental activation of power during
service work.
The completeness and functionality of
field supplied electrical controls and
components must be verified by the
heating contractor. These include low
water cut-offs, flow switches (if used),
staging controls, pumps, motorized
valves, air vents, thermostats, etc.
Technical literature
Literature for the Vitodens oiler:
- Technical Data Manual
- Installation Instructions
- Start-up/Service Instructions
- Operating Instructions
and User’s Information Manual
- Instructions of other Viessmann
products utilized and installed
- Installation codes mentioned
in this manual
Leave all literature at the installation
site and advise the system
operator/ultimate owner where the
literature can be found. Contact
Viessmann for additional copies.
This product comes with several
safety instruction labels attached.
Do not remove!
Contact Viessmann immediately if
replacement labels are required.
5418 911 2

General Information
6
Important Regulatory and Installation Requirements (continued)
Special Requirements for Side-Wall Vented Appliances
In the Commonwealth of Massachusetts
The Commonwealth of Massachusetts requires compliance with regulation 248 CMR 4.00 and 5.00 for installation of
side-wall vented gas appliances as follows:
(a) For all side-wall horizontally vented gas fueled equipment installed in every dwelling, uilding or structure used in whole
or in part for residential purposes, including those owned or operated y the Commonwealth and where the side-wall
exhaust vent termination is less than (7) feet a ove finished grade in the area of the venting, including ut not limited to
decks and porches, the following requirements shall e satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side-wall horizontal vented
gas fueled equipment, the installing plum er or gasfitter shall o serve that a hard wired car on monoxide detector
with an alarm and attery ack-up is installed on the floor level where the gas equipment is to e installed. In
addition, the installing plum er or gasfitter shall o serve that a attery operated or hard wired car on monoxide
detector with an alarm is installed on each additional level of the dwelling, uilding or structure served y the
side-wall horizontal vented gas fueled equipment. It shall e the responsi ility of the property owner to secure the
services of qualified licensed professional for the installation of hard-wired car on monoxide detectors.
a. In the event that the side-wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard-wired car on monoxide detector with alarm and attery ack-up may e installed on the next adjacent
floor level.
. In the event that the requirements of this su division can not e met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply with the a ove requirements; provided, however, that
during said thirty (30) day period, a attery operated car on monoxide detector with an alarm shall e installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each car on monoxide detector as required in accordance with the
a ove provisions shall comply with NFPA 720 and e ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall e permanently mounted to the exterior of the uilding at a
minimum height of eight (8) feet a ove grade directly in line with the exhaust vent terminal for the horizontally vented
gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size,
”GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side-wall horizontally vented gas fueled equipment shall not
approve the installation unless, upon inspection, the inspector o serves car on monoxide detectors and signage
installed in accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.
( ) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a) 1 through 4:
1. The equipment listed in Chapter 10 entitled ”Equipment Not Required To Be Vented” in the most current edition of
NFPA 54 as adopted y the Board; and
2. Product Approved side-wall horizontally vented gas fueled equipment installed in a room or structure separate from
the dwelling, uilding or structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of
Product Approved side-wall horizontally vented gas equipment provides a venting system design or venting system
components with the equipment, the instructions provided y the manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
5418 911 2

General Information
7
Important Regulatory and Installation Requirements (continued)
Special Requirements for Side-Wall Vented Appliances
In the Commonwealth of Massachusetts (continued)
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side-wall horizontally vented gas fueled equipment does not provide the parts for venting the flue
gases, ut identifies ”special venting systems”, the following requirements shall e satisfied y the manufacturer:
1. The referenced ”special venting system” instructions shall e included with the appliance or equipment installation
instructions; and
2. The ”special venting systems” shall e Product Approved y the Board, and the instructions for that system shall
include a parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side-wall horizontally vented gas fueled equipment, all
venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the
appliance or equipment at the completion of the installation.
5418 911 2

General Information
8
About these Start-up/Service Instructions
Take note of all symbols and notations intended to draw attention to potential hazards or important product information.
These include ”WAR I G”, ”CAUTIO ”, and ”IMPORTA T”. See below.
Warnings draw your attention to the
presence of potential hazards or
important product information.
Cautions draw your attention to the
presence of potential hazards or
important product information.
Helpful hints for installation,
operation or maintenance which
pertain to the product.
This symbol indicates that additional,
pertinent information is to be found in
column three.
This symbol indicates that other
instructions must be referenced.
ecessary Tools
Special items
HApproved leak detection fluid for
natural gas and propane gas
HPipe joint sealant
Testing/analysis equipment
HMultimeter to measure 0 - 230 V,
0 - 12 A AC and 0 - 100 A DC
HFlue gas analyzer to measure % CO
2
or O
2
(i.e. Bacharach fluid samplers
or suita le electronic analyzer)
HManometer to measure gas pressure
0 to 11 ”w.c. (accurately) and up to
28 ”w.c. gas pressure (or a
non-electric Magnehelic® manometer
may also e utilized)
HStack thermometer 0 to 500 °F /
0 to 260 °C
HBacharach calculator or suita le
ta les to calculate efficiency
HCar on monoxide measuring
equipment 0 to 400 ppm
Use only calibrated equipment.
Cleaning supplies
HPlastic hand rush
HRags
5418 911 25418 911 2
Indicates an imminently hazardous
situation which, if not avoided, could
result in death, serious injury or
substantial product/property damage.
WAR I G
Indicates an imminently hazardous
situation which, if not avoided, may
result in minor injury or
product/property damage.
CAUTIO
IMPORTA T
5418 911 2

General InformationGeneral Information
9
Applicability
When ordering replacement parts,
provide either the 16-digit serial
number (on the bar code label) or the
12-digit ASME/ B serial number,
located as shown underneath boiler
front enclosure panel. Refer to page 11
for instructions on how to remove front
enclosure panel.
Model o. WB2B 9-19
Serial No. 7374863 jjjjjjjjj
Model o. WB2B 9-26
Serial No. 7374864 jjjjjjjjj
Model o. WB2B 9-35
Serial No. 7374865 jjjjjjjjj
Product Information
Natural/Propane gas-fired wall-mounted condensing heating oiler for
weather-responsive operation in closed loop, forced circulation hot water heating
systems for space heating and domestic hot water (DHW) production.
The Vitodens 200, WB2B series oiler comes factory set for operation with
natural gas. For a fuel conversion to propane gas no conversion kit is required
(see page 17).
Boiler model must e selected ased on an accurate heat loss calculation of the
uilding. Ensure oiler model is compati le with connected radiation.
Vitodens 200, WB2B series oilers are factory-tested and cali rated. Further gas
valve adjustments are not typically required during field start-up.
Follow the Vitodens Venting System Installation Instructions to vent
this boiler.
5418 911 2
IMPORTA T
Fig. 1
Locating boiler serial numbers for ordering
replacement parts
1 -digit ASME/NB serial number
(located on metallic plate riveted
to the heat exchanger)
16-digit serial number on white
bar code label
5418 911 2

General Information
10
Mechanical Room
During the early stages of designing a new home, we recommend that proper consideration e given to constructing a
separate mechanical room dedicated to the gas- or oil-fired heating equipment and domestic hot water storage tank(s).
The oiler must e located in a heated indoor area, near a floor drain, and as close as possi le to a wall. Whenever possi le,
install the oiler near an outside wall so that it is easy to duct the venting system to the oiler.
Locate the oiler on a wall capa le of supporting the weight of the oiler filled with water (see section entitled “Technical
Data” on page 75 for information required for total oiler weight calculation). Ensure that the oiler location does not
interfere with the proper circulation of com ustion and ventilation air of other fuel urning equipment within the mechanical
room (if applica le).
The maximum room temperature of the mechanical room where the oiler is located must not exceed 104 ºF/40 ºC.
Installation area conditions
HEnsure am ient temperatures are
higher than 32°F / 0°C and lower
than 104°F / 40°C.
HPrevent the air from ecoming
contaminated y halogenated
hydrocar ons (e.g. as contained in
paint solvents or cleaning fluids) and
excessive dust (e.g. through grinding
or polishing work). Com ustion air for
the heating process, and ventilation
of the oiler room must e free of
corrosive contaminants. To that end,
any oiler must e installed in an area
that has no chemical exposure. The
list to the right indicates the main,
currently known sources.
HAvoid continuously high levels of
humidity (e.g. through frequent
drying of laundry).
HNever close existing ventilation
openings.
Sources of combustion and ventilation
air contaminants
Areas likely to contain contaminants:
HNew uilding construction
HSwimming pools
HRemodelling areas, ho y rooms
HGarages with workshops
HFurniture refinishing areas
HDry cleaning/laundry areas and
esta lishments
HAuto ody shops
HRefrigeration repair shops
HMetal fa rication plants
HPlastic manufacturing plants
HPhoto processing plants
HBeauty salons
Products containing contaminants:
HChlorine-type leaches, detergents
and cleaning solvents found in
household laundry rooms
HPaint and varnish removers
HHydrochloric acid, muriatic acid
HChlorine- ased swimming pool
chemicals
HSpray cans containing
chlorofluorocar ons
HChlorinated waxes and cleaners
HCements and glues
HRefrigerant leaks
HCalcium chloride used for thawing
HSodium chloride used for water
softening salt
HPermanent wave solutions
HAdhesives used to fasten uilding
products and other similar items
HAntistatic fa ric softeners used in
clothes dryers
Boiler operation in marine environments
(damp, salty coastal areas)
The service life of the oiler’s exposed
metallic surfaces, such as the casing
and fan housing, is directly influenced
y proximity to damp and salty marine
environments. In such areas, higher
concentration levels of chlorides from
sea spray, coupled with relative
humidity, can lead to degradation of
the exposed metallic surfaces
mentioned a ove. Therefore, it is
imperative that oilers installed in such
environments not e installed using
direct vent systems which draw
outdoor air for com ustion. Such
oilers must e installed using room air
dependent vent systems; i.e. using
room air for com ustion. The indoor air
will have a much lower relative
humidity and, hence, potential
corrosion will e minimized.
5418 911 2
Incorrect ambient conditions can lead
to damage to the heating system and
put safe operation at risk.
WARNING
If you notice fire coming from the
appliance, call the fire department
immediately! Do not attempt to
extinguish the fire unless qualified to
do so.
WARNING
Fire causes a risk of burns and
explosion!
H
HH
HShut down the boiler
H
HH
HClose fuel shut-off valves
H
HH
HUse a tested fire extinguisher,
class ABC.
WARNING
IMPORTA T