ViewSonic VS18176 User manual

LS600W
Projector
User Guide
Model No. VS18176
Model Name: LS600W
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product
in a safe manner, as well as registering your product for future service. Warranty information contained in this
User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at
http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right
corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

2
Thank you for choosing ViewSonic®
As a world-leading provider of visual soluons, ViewSonic® is dedicated to exceeding the
world’s expectaons for technological evoluon, innovaon, and simplicity. At ViewSonic®,
we believe that our products have the potenal to make a posive impact in the world, and
we are condent that the ViewSonic® product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic®!

3
Safety Precautions - General
Please read the following Safety Precautions before you start using the projector.
• Keep this user guide in a safe place for later reference.
• Read all warnings and follow all instructions.
• Allow at least 20“ (50 cm) clearance around the projector to ensure proper
ventilation.
• Place the projector in a well-ventilated area. Do not place anything on the
projector that prevents heat dissipation.
• Do not place the projector on an uneven or unstable surface. The projector may
fall over, causing personal injury or projector malfunction.
• Do not use if the projector is tilted at an angle of more than 10° degrees left or
right, nor at an angle of more than 15° degrees forwards or backwards.
• Do not look straight at the projector lens during operation. The intense light
beam may damage your eyes.
• Always open the lens shutter or remove the lens cap when the projector light
source is on.
• Do not block the projection lens with any objects when the projector is under
operation as this could cause objects to become heated and deformed or even
cause a fire.
• The light source becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the light source assembly
for replacement.
• Do not use light sources beyond the rated light source life. Excessive use of light
sources beyond the rated life could cause them to break on rare occasions.
• Never replace the light source assembly or any electronic component unless the
projector is unplugged.
• Do not attempt to disassemble the projector. There are dangerous high voltages
inside which may cause death if you should come into contact with live parts.
• When moving the projector, be careful not to drop or bump the projector on
anything.
• Do not place any heavy objects on the projector or connection cables.
• Do not stand the projector on end vertically. Doing so may cause the projector
to fall over, causing personal injury or projector malfunction.
• Avoid exposing the projector to direct sunlight or other sources of sustained
heat. Do not install near any heat sources such as radiators, heat registers,
stoves, or other devices (including amplifiers) that may increase the
temperature of the projector to dangerous levels.
• Do not place liquids near or on the projector. Liquids spilled into the projector
may cause it to fail. If the projector does become wet, disconnect it from the
power supply and call your local service center to have the projector serviced.

4
• When the projector is under operation, you may sense some heated air and
odor from its ventilation grill. It is a normal operation and not a defect.
• Do not attempt to circumvent the safety provisions of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding prong. The
wide and third blade are provided for your safety. If the plug does not fit into
your outlet, obtain an adapter and do not attempt to force the plug into the
outlet.
• When connecting to a power outlet, DO NOT remove the grounding prong.
Please ensure grounding prongs are NEVER REMOVED.
• Protect the power cord from being treaded upon or pinched, particularly at the
plug, and at the point where it emerges from the projector.
• In some countries, the voltage is NOT stable. This projector is designed to
operate safely within a voltage between 100 to 240 volts AC, but could fail if
power cuts or surges of ±10 volts occur. In areas where voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector, or uninterruptable power supply (UPS).
• If smoke, an abnormal noise, or a strange odor is present, immediately switch
the projector off and call your dealer or ViewSonic®. It is dangerous to continue
using the projector.
• Use only attachments/accessories specified by the manufacturer.
• Disconnect the power cord from the AC outlet if the projector is not being used
for a long period of time.
• Refer all servicing to qualified service personnel.
CAUTION: Possibly hazardous optical radiation is emitted from this product. As
with any bright light source, do not stare into the beam,
RG2 IEC 62471-5:2015.

5
Safety Precautions - Ceiling Mounting
Please read the following Safety Precautions before you start using the projector.
If you intend to mount the projector on the ceiling, we strongly recommend
that you use a proper fitting projector ceiling mount kit and that you ensure it is
securely and safely installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use
of the wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your
projector. We recommend that you also purchase a separate security cable and
attach it securely to both the anti-theft lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the
projector should its attachment to the mounting bracket become loose.

6
Contents
Safety Precautions - General ....................................... 3
Introduction .............................................................. 10
Features................................................................................................................10
Package Contents .................................................................................................10
Product Overview.................................................................................................11
Projector................................................................................................................ 11
Controls and Functions ............................................................................................... 11
Connection Ports......................................................................................................... 12
Remote Control..................................................................................................... 13
Controls and Functions ............................................................................................... 13
Remote Control Effective Range................................................................................. 14
Replacing the Remote Control Batteries..................................................................... 14
Initial Setup............................................................... 15
Choosing a Location..............................................................................................15
Projection Dimensions..........................................................................................16
16:10 Image on a 16:10 Screen................................................................................... 16
16:10 Image on a 4:3 Screen....................................................................................... 17
Mounting the Projector........................................................................................18
Preventing Unauthorized Use...............................................................................19
Using the Security Slot .......................................................................................... 19
Using the Password Function................................................................................ 20
Setting a Password...................................................................................................... 20
Changing the Password............................................................................................... 21
Disabling the Password Function ................................................................................ 21
Forgetting the Password............................................................................................. 22
Password Recall Procedure......................................................................................... 22
Locking the Control Keys....................................................................................... 22

7
Making Connections.................................................. 23
Connecting to Power ............................................................................................23
Connecting to Video Sources................................................................................24
HDMI Connection.................................................................................................. 24
Composite Video Connection................................................................................ 25
Connecting to Computer Sources.........................................................................26
VGA Connection .................................................................................................... 26
VGA Out Connection ............................................................................................. 26
Connecting to Audio.............................................................................................27
Operation.................................................................. 28
Turning the Projector On/Off ...............................................................................28
Starting Up the Projector ...................................................................................... 28
First Time Activation ................................................................................................... 28
Shutting Down the Projector................................................................................. 29
Selecting an Input Source.....................................................................................30
Adjusting the Projected Image .............................................................................31
Adjusting the Projector's Height and Projection Angle............................................... 31
Auto-Adjusting the Image ........................................................................................... 31
Fine-Tuning the Image Size and Clarity ................................................................. 31
Correcting Keystone.............................................................................................. 32
Hiding the Image ..................................................................................................33
Controlling the Projector through a LAN Environment ........................................34
Configuring the LAN Control Settings.................................................................... 34
Controlling the Projector through a Web Browser ............................................... 36
About Crestron e-Control®.................................................................................... 40
PJLink™, SNMP, AMX and Xpanel Formats Supported.......................................... 43

8
Menu Functions ........................................................ 44
General On-Screen Display (OSD) Menu Operation .............................................44
On-Screen Display (OSD) Menu Tree....................................................................45
DISPLAY Menu ......................................................................................................50
IMAGE Menu ........................................................................................................53
POWER MANAGEMENT Menu .............................................................................56
BASIC Menu..........................................................................................................59
ADVANCED Menu .................................................................................................62
SYSTEM Menu.......................................................................................................66
INFORMATION Menu ...........................................................................................69
Appendix................................................................... 70
Specifications........................................................................................................70
Projector Dimensions............................................................................................ 71
Timing Chart .........................................................................................................71
Analog RGB............................................................................................................ 71
HDMI (PC).............................................................................................................. 73
HDMI (Video)......................................................................................................... 74
Video/S-Video ....................................................................................................... 74
Component video.................................................................................................. 75
IR Control Table ....................................................................................................76
Address Code........................................................................................................77
RS-232 Command Table .......................................................................................78
Pin Assignment...................................................................................................... 78
Interface................................................................................................................ 78
Command Table .................................................................................................... 78
Glossary ................................................................................................................87
Troubleshooting ...................................................................................................90
Common Problems................................................................................................ 90
LED Indicators........................................................................................................ 91
Maintenance.........................................................................................................92
General Precautions.............................................................................................. 92
Cleaning the Lens .................................................................................................. 92
Cleaning the Case.................................................................................................. 92
Storing the Projector............................................................................................. 92
Disclaimer.............................................................................................................. 92
Light Source Information......................................................................................93
Light Source Hour.................................................................................................. 93
Extending Light Source Life ................................................................................... 93

9
Regulatory and Service Information .......................... 94
Compliance Information.......................................................................................94
FCC Compliance Statement................................................................................... 94
Industry Canada Statement................................................................................... 94
CE Conformity for European Countries ................................................................. 94
Declaration of RoHS2 Compliance......................................................................... 95
Indian Restriction of Hazardous Substances ......................................................... 96
Product Disposal at End of Product Life................................................................ 96
Copyright Information ..........................................................................................97
Customer Service .................................................................................................. 98
Limited Warranty .................................................................................................. 99
Mexico Limited Warranty.................................................................................... 102

10
The LS600W is a 3,000 ANSI Lumens, high brightness WXGA Lamp Free Projector
for business and education. Adopting 2nd generation LED technology, it frees users
from frequent lamp replacement and toxic mercury, offers an amazing 30,000 hours
long lifespan, true-to-life colors with 125% Rec.709, as well as instant power on/
off for efficient power saving. Its comprehensive LAN control eases multiple device
management and is compatible with Crestron, AMX, Extron, PJ Link, ATEN, and
ViewSonic’s vController. Enjoy all the amazing features this projector has to offer with
hassle-free setup, 360° tilt angle projection, 1.2x zoom lens, H/V Keystone, and 4 Corner
adjustment.
Features
• Lamp free, Mercury free, Maintenance free
• 2nd generaon LED Technology with 30,000 hours lifespan
• Instant power on/o
• 3,000 ANSI Lumens oering bright images in any environment
• 360° projecon and H/V keystone for easy installaon
• Cinema SuperColor+™ Technology with 125% Rec.709
• H/V Keystone enabling side projecons
• Comprehensive LAN control for ecient management*
Package Contents
• Projector
• Power Cord
• Video Cable
• Remote Control & Baeries
• Quick Start Guide
NOTE: The power cord and video cables included in your package may vary depending
on your country. Please contact your local reseller for more informaon.
Introduction

11
Product Overview
Projector
Controls and Functions
MENU
EXIT
SOURCE
?
ENTER
BLANK
COLOR
MODE
Power Indicator Light
Temperature Indicator Light
Light Source Indicator Light
Projection Lens
Remote IR sensor
Power key
Remote IR sensor
Focus Ring
Zoom Ring
Key Description
[ ] Power Toggles the projector between standby mode and Power On.
[ / / / ] Keystone
Keys
Manually corrects distorted images resulting from an angled
projection.
[ / / / ]
Left/Right/Up/Down
Selects the desired menu items and makes adjustments when
the On-Screen Display (OSD) Menu is activated.
Menu/Exit Turns on or off the On-Screen Display (OSD) Menu.
Source Displays the input source selection bar.
(Help) Displays the HELP menu.
Blank Hides the screen picture.
Enter Enacts the selected On-Screen Display (OSD) Menu item when
the OSD Menu is activated.
[ ] Corner Adjustment Displays the Corner Adj. menu when the OSD menu is not
activated.
Color Mode Displays the color mode selection bar.

1212
Connection Ports
AUDIO OUTRJ-45AUDIO IN COMPUTER IN VIDE
OR
S-232
HDMI 1HDMI 2USB 5V/1.5A OUT
(Service)
1235 8 9
67 4
AC Power Cord Inlet
Ceiling Mount Holes
Security Slot
Security Bar
Adjuster Foot
Port Description
[1] RJ-45 LAN port.
[2] AUDIO OUT Audio signal output socket.
[3] AUDIO IN Audio signal input socket.
[4] HDMI 1 HDMI port.
[5] HDMI 2 HDMI port.
[6] COMPUTER IN RGB (PC) signal input socket.
[7] VIDEO Composite video port.
[8] USB 5V/1.5A OUT (Service) USB Type A port for power supply and serivce.
[9] RS-232 RS-232 control port.

13
Remote Control
Controls and Functions
Button Description
On/ Off Toggles between standby
mode and Power On.
COMP Selects the source from
the COMPUTER IN port for
display.
HDMI 1 Selects the source from the
HDMI 1 port for display.
HDMI 2 Selects the source from the
HDMI 2 port for display.
Auto Sync Automatically determines
the best picture timings for
the displayed image.
Source Displays the source selection
bar.
[ / / / ]
Keystone Keys
Manually corrects distorted
images resulting from an
angled projection.
Enter Enacts the selected OSD
Menu item.
(Corner
adjustment)
Displays the Corner Adj.
menu when the OSD menu is
not activated.
Button Description
Left/ Right
Up/ Down
Selects the desired menu
items and makes adjustments.
Menu Turns on/off the On-Screen
Display (OSD) Menu or goes
back to previous OSD Menu.
(Laser)
Emits visible laser pointer light
for presentation purposes.
Exit Exits and saves menu
settings.
Aspect Displays the aspect ratio
selection bar.
Freeze Freezes the projected image.
Pattern Displays embedded test
pattern.
Blank Hides the screen picture.
PgUp (Page Up)/
PgDn (Page
Down)
Operates your display
software program (on
a connected PC) which
responds to page up/down
commands (like Microsoft
PowerPoint).
NOTE: Only available when
a PC input signal is
selected.
(Presentation
Timer)
Displays the
Presentation Timer menu.
Eco Mode Selects the Eco mode.
(Volume Up) Increases the volume level.
(Volume
Down)
Decreases the volume level.
(Mute) Toggles audio between on
and off.
Color Mode Displays the color mode
selection bar.
Magnifies the projected
picture size.
Reduces the projected
picture size.
(INFORMATION)
Displays the INFORMATION
menu.
Network Displays the
LAN Control Settings menu.

14
Remote Control Effective Range
To ensure proper function of the remote control
follow the steps below:
1. The remote control must be held at an angle
within 30° perpendicular to the projector’s IR
remote control sensor(s).
2. The distance between the remote control and
the sensor(s) should not exceed 8 m (26 ft.)
NOTE: Refer to the illustration for the location of
the infrared (IR) remote control sensor(s).
Approx. 30°
Approx. 30°
Replacing the Remote Control Batteries
1. Remove the battery cover from the rear of the remote control by pressing the
finger grip and sliding it down.
2. Remove any existing batteries (if necessary) and install two AAA batteries.
NOTE: Observe the battery’s polarities as indicated.
3. Replace the battery cover by aligning it with the base and pushing it back into
position.
NOTE:
• Avoid leaving the remote control and batteries in excessive heat or a humid
environment.
• Replace only with the same or equivalent type recommended by the battery
manufacturer.
• Dispose of the used batteries according to the manufacturer’s instructions and
local environment regulations for your region.
• If the batteries are drained or if you will not be using the remote control for an
extended period of time, remove the batteries to avoid damage to the remote
control.

15
Initial Setup
This section provides detailed instructions for setting up your projector.
Choosing a Location
Personal preference and room layout will decide the installation location. Consider
the following:
• Size and Position of your screen.
• Location of a suitable power outlet.
• Location and Distance between the projector and other equipment.
The projector is designed to be installed in one of the following locations:
1. Front
The projector is placed near the floor in
front of the screen.
2. Front Ceiling
The projector is suspeneded upside-
down from the ceiling in front of the
screen.
3. Rear Ceiling
The projector is suspended upside-down
from the ceiling behind the screen.
NOTE: A special rear projection screen
is required.
4. Rear
The projector is placed near the floor
behind the screen.
NOTE: A special rear projection screen
is required.

16
Projection Dimensions
NOTE: See “Specifications” on page 70 for the native display resolution of this
projector.
• 16:10 Image on a 16:10 Screen
• 16:10 Image on a 4:3 Screen
(a)
(c)
(b)
(e)
(f)
(d)
NOTE: (e) = Screen / (f) = Center of Lens
16:10 Image on a 16:10 Screen
(a) Screen
Size
(b) Projection Distance (c) Image
Height
(d) Vertical Offset
minimum maximum minimum maximum
in. mm in. mm in. mm in. mm in. mm in. mm
30 762 35 883 42 1059 16 404 13 319 12.6 319
40 1016 46 1177 56 1412 21 538 17 425 16.7 425
50 1270 58 1471 70 1766 26 673 21 532 20.9 532
60 1524 70 1766 83 2119 32 808 25 638 25.1 638
70 1778 81 2060 97 2472 37 942 29 744 29.3 744
80 2032 93 2354 111 2825 42 1077 33 851 33.5 851
90 2286 104 2648 125 3178 48 1212 38 957 37.7 957
100 2540 116 2943 139 3531 53 1346 42 1063 41.9 1063
120 3048 139 3531 167 4237 64 1615 50 1276 50.2 1276
150 3810 174 4414 209 5297 79 2019 63 1595 62.8 1595
200 5080 232 5885 278 7062 106 2692 84 2127 83.7 2127
250 6350 290 7356 348 8828 132 3365 105 2659 104.7 2659
300 7620 348 8828 417 10593 159 4039 126 3190 125.6 3190

17
16:10 Image on a 4:3 Screen
(a) Screen
Size
(b) Projection Distance (c) Image
Height
(d) Vertical Offset
minimum maximum minimum maximum
in. mm in. mm in. mm in. mm in. mm in. mm
30 762 33 833 39 999 15 381 12 301 12 301
40 1016 44 1110 52 1332 20 508 16 401 16 401
50 1270 55 1388 66 1666 25 635 20 502 20 502
60 1524 66 1666 79 1999 30 762 24 602 24 602
70 1778 77 1943 92 2332 35 889 28 702 28 702
80 2032 87 2221 105 2665 40 1016 32 803 32 803
90 2286 98 2498 118 2998 45 1143 36 903 36 903
100 2540 109 2776 131 3331 50 1270 40 1003 40 1003
120 3048 131 3331 157 3997 60 1524 47 1204 47 1204
150 3810 164 4164 197 4997 75 1905 59 1505 59 1505
200 5080 219 5552 262 6662 100 2540 79 2007 79 2007
250 6350 273 6940 328 8328 125 3175 99 2508 99 2508
300 7620 328 8328 393 9994 150 3810 119 3010 119 3010
NOTE: There is a 3% tolerance among these numbers due to optical component
variations. It is recommended to physically test the projection size and
distance before permanently installing the projector.

18
Mounting the Projector
NOTE: If you buy a third-party mount, please use the correct screw size. Screw size
can vary depending on the thickness of the mounting plate.
1. To ensure the most secure installation, please use a ViewSonic® wall or ceiling
mount.
2. Ensure the screws used to attach a mount to the projector meet the following
specifications:
• Screw type: M4
• Screw length: 12.8 mm ~ 15.8 mm
145.6
176.6
282.9
305.9
NOTE:
• Avoid installing the projector near a heat source.
• Keep at least a 10 cm gap between the ceiling and the bottom of the
projector.

19
Preventing Unauthorized Use
The projector has several built-in security features to prevent theft, access, or
accidental setting changes.
Using the Security Slot
To help prevent the projector from being stolen, use a security slot locking device
to secure the projector to a fixed object.
Below is an example of setting up a security slot locking device:
NOTE: The security slot can also be used as a safety anchor if the projector is
mounted to the ceiling.

2020
Using the Password Function
To help prevent unauthorized access or use, the projector offers a password
security option. The password can be set through the On-Screen Display (OSD)
Menu.
NOTE: Make note of your password, and keep it in a safe place.
Setting a Password
1. Press Menu to open the OSD Menu and go to: SYSTEM > Security Settings and
press Enter.
2. Highlight Power On Lock and select
On by pressing / .
3. As pictured to the right, the four
arrow keys ( , , , ) represent
4 digits (1, 2, 3, 4). Press the arrow
keys to enter a six digit password.
4. Confirm the new password by re-entering the new password. Once the password
is set, the OSD Menu will return to the Security Settings page.
5. Press Exit to leave the OSD Menu.
NOTE: Once set, the correct password must be entered every time the projector is
started.