Viking PA-250-IP User manual

1.3 Download and install the programming software
1. Go to www.vikingelectronics.com and enter PA-250-IP in the search box
2. Click PA-250-IP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on
setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
QUICK START GUIDE
VIKING Electronics, Inc.
KSee Product Manual for complete installation and programming instructions.
1.0 Out-of-Box
1.1 Verify that you have received all of the parts listed
1.2 Download the product manual
1. Go to www.vikingelectronics.com and
enter PA-250-IP in the search box
2. Under Documents click Product Manual
to open and download the PDF
Scan the QR code to
open and download
the product manual
- OR -
PA-250-IP
250 Watt 70V SIP /
Multicast Paging Amplifier
January 22, 2021
X 1 Terminal Strip 4 Pin 5mm
Right Angle Removable
X 1 Terminal Strip 5 Pin 5mm
Right Angle Removable
X 1 Terminal Strip 2 Pin 5mm
Right Angle Removable
X 1 PA-250-IP
X 1 Y Power Cord
X 1 Bit slotted 2.5 mm
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full duplex
• Disable Spanning Tree Protocol (STP) or enable Portfast
2.0 Network Port Settings

3.0 Features Overview
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
PA-250-IP Quick Start Guide ZF304291 REV A
ALC: Automatic Level Control adjustment for PAGE input
PAGE: Paging Input volume control and LED showing activity and audio level
AUX: Auxiliary Input volume control and LED showing activity and audio level
CHIME: Volume control and LED indicator for Chime tones
MUSIC: Volume control for Background Music Input
BASS: Low frequency tone control
TREBLE: High frequency tone control
MASTER VOLUME: Master volume control and LED level indicator for setting Peak Limiting
POWER: LED indicating power is on (winks off to indicate an overload condition)
Multicast Paging Amplifier
250 Watt SIP/ AUXPAGE CHIME BASS
MASTER
VOLUMETREBLE
POWER
MUSIC
VIKING MODEL PA-250-IP
Multicast Paging Amplifier ALC
AUX INPUT:
Auxiliary analog input
SHIELD:
Analog ground
600 OHM OUTPUT:
Output for driving additional amplifiers
BACKGROUND MUSIC INPUT:
3.5mm jack for connecting music source
CHIME TRIG:
To trigger doorbell chime tones
SPEAKERS: Connect up to two hundred fifty
(250) 70V or 25V speakers and/or paging horns
Yellow Network Status LED: Lights steady
to indicate power and data link. Blinks to indicate
network activity.
LAN Port 10/100: Connect to your LAN via
RJ45 plug and CAT5 or greater twisted pair wire.
Green Unit Status LED
Reset Button
MAC Address Label: The MAC address is a
unique 12 digit number used by network equipment
to send data packets to the correct IP address.
SPEAKERS
SPEAKERS LAN
RESET
BACKGND MUSIC INPUT
AC POWER INPUT
(BOTH REQUIRED)
+
SHIELD
AUX INPUT 25V
70V
25V CHIME TRIG 600 OHM OUTPUT
123 45 6 8910117
+ +
MODEL PA-250-IP
VIKING
250 Watt SIP/
Multicast Paging Amplifier
MAC: 18E80FXXXXXX
AC POWER INPUT:
Connect to 100V to 240V AC power
using the included “Y” power cord
4.0 Connections
Use included slotted bit to adjust tamper resistant front panel pots.