Viking E-20 User manual

PRODUCT MANUAL
Designed, Manufactured and Supported in the USA
COMMUNICATION & SECURITY SOLUTIONS
E-10/20/30-IP
VoIP Entry Phones
February 27, 2015
VIKING
Features Applications
Specifications
www.vikingelectronics.com
Information: [phone]
VoIP Entry Phones
• Self diagnostic reports via email (testing com, mic, speaker & switch)
• Automatic polling and programming software included
• 2 Amp relay contacts for door/gate or SL-2 strobe light control
• Blue “Call Connected” LED indicator (E-10/E-30-IP only)
• SIP compatible (see pg 2 for list of compatible IP-PBX phone systems)
• PoE powered (class 1, <4 watts)
• Automatic Noise Canceling (ANC) feature for proper operation in noisy envi-
ronments
• VoIP eliminates the need for “Push to Talk” mode
• Network downloadable firmware
• Handsfree operation
• Marine grade 316 stainless steel prevents corrosion on the stainless steel models
• Programmable to dial up to 5 numbers on busy or ring no answer
• Cycles through backup phone numbers on busy or no-answer
• Optional Enhanced Weather Protection (EWP), EWP products are designed to
meet IP66 Ingress Protection Rating, see DOD# 859
• Hangs up on busy signal, time-out or touch tone command
• Remotely programmable
• Extended temperature range (-30°F to 130°F)
• 3 different chassis or board only available
• Volume adjustments for microphone and speaker
• E-10-IP and E-30-IP are flush mountable using the included rough-in box or can
be surface mounted using an optional VE-5x5 Surface Mount Box (DOD# 424)
• Optional PB-100 Polling System available (DOD# 232)
• Optional SL-2 or BLK-4-EWP strobe light kit available (DOD# 242/653)
Power: PoE class 1 (<4 watts)
Dimensions: See Installation and Specifications
Operating Temperature: -34° C to 54° C (-30°F to 130°F)
Humidity - Standard Products: 5% to 95% non-condensing
Humidity - EWP Products: Up to 100%
Audio Codecs: G711u, G711a, G722
Connections: (1) RJ45 10/100 Base-T, (3) gel-filled butt con-
nectors
Installation requires the assistance of a Network Administrator / IT Technician.
Beta Units Available
!
The E-10/20/30-IP VoIP Entry Phones are designed to provide quick and
reliable handsfree communication for SIP VoIP phone systems with PoE.
The E-10/20/30-IP entry phones can be programmed from any Touch
Tone phone or PC on the same LAN. The Entry phones can dial up to 5
programmable numbers.
The E-10/20/30-IP entry phones will flash the “Call” LED during dialing
and automatically light the LED when the call is answered. All program-
ming parameters, including phone numbers and location numbers, are
stored in non-volatile memory, requiring no batteries. All units are PoE
powered.
For outdoor installations where the unit is exposed to precipitation or con-
densation, the E-10/20/30-IP Entry phones are available with Enhanced
Weather Protection (EWP). EWP products feature foam rubber gaskets
and boots, sealed connections, gel-filled butt connectors, as well as ure-
thane or thermal plastic potted circuit boards. For more information, see
DOD# 859.
E-10-IP/E-10-IP-EWP
Flush Mount Black
Powder Painted Aluminum
E-20-IP/E-20-IP-EWP
Surface Mount Light Grey
UV Stable Plastic Chassis
E-30-IP/E-30-IP-EWP
Flush Mount Brushed 316
Stainless Steel
E-30-IP/E-30-IP-EWP
Shown in Optional VE-5x5
Surface Mount Box
• Gate Entrance
• Parking ramps/lots
• ATM machines
• Medical centers
• Lobbies
• Entryways
• Stadiums
• Convention centers
• Public access areas

Viking VoIP SIP System Compatibility List
NOTE: Exclusion from this list means only that compatability has not been verified, it does not mean
incompatability.
2
For detailed configuration instructions for certain vendors below, see Configuring Viking VoIP Phone
and SIP Servers,DOD# 944.
Vendor
Infrastructure Class
Softswitch PBX Proxy SBC
(session border
controller)
Service
Provider
3COM VCX X
3CX X
Aastra X
Asterisk X
Atcom X
Avaya IP Office X
BlueBox X
Brekeke X
Cisco Unified Communications Manager (CUCM) X X
Cisco Unified Communications Manager Express
(CUCME) X X
Freeswitch X
Grandstream X
iptel.org X
Kamailio X X
MetaSwitch XX
OfficeSIP X
OpenSIPS X
Panasonic X
Samsung Communications Manager (SCM) X X
ShoreTel X
Siemens Communications Server (SCS) X
SIP Express Router (SER) X X
sip.antisip.com X
Snom PBX X
Sonus X
Switchvox X X
Teksip X
Toshiba X
VoIP.ms X

3
Definitions
Client: A computer or device that makes use of a server. As an example, the client might request a particular file from the
server.
DHCP: Dynamic Host Configuration Protocol. In this procedure the network server or router takes note of a client’s MAC
address and assigns an IP address to allow the client to communicate with other devices on the network.
DNS Server: A DNS (Domain Name System) server translates domain names (ie: www.vikingelectronics.com) into an IP
address.
Ethernet: Ethernet is the most commonly used LAN technology. An ethernet Local Area Network typically uses twisted
pair wires to achieve transmission speeds up to 1Gbps.
Host: A computer or device connected to a network.
Host Name: A host name is a label assigned to a device connected to a computer network that is used to identify the device
in various forms of network communication.
Hosts File: A file stored in a computer that lists host names and their corresponding IP addresses with the purpose of map-
ping addresses to hosts or vice versa.
Internet: A worldwide system of computer networks running on IP protocol which can be accessed by individual computers
or networks.
IP: Internet Protocol is the set of communications conventions that govern the way computers communicate on networks
and on the Internet.
IP Address: This is the address that uniquely identifies a host on a network.
LAN: Local Area Network. A LAN is a network connecting computers and other devices within an office or building.
Lease: The amount of time a DHCP server reserves an address it has assigned. If the address isn’t used by the host for
a period of time, the lease can expire and the address can be assigned to another host.
MAC Address: MAC stands for Media Access Control. A MAC address, also called a hardware address or physical address,
is a unique address assigned to a device at the factory. It resides in the device’s memory and is used by routers to send
network traffic to the correct IP address. You can find the MAC address of your E-10/20/30-IP phone printed on a white
label on the top surface of the PoE LAN port.
Router: A device that forwards data from one network to another. In order to send information to the right location, routers
look at IP Address, MAC Address and Subnet Mask.
Server: A computer or device that fulfills requests from a client. This could involve the server sending a particular file re-
quested by the client.
Session Initiation Protocol (SIP): Is a signaling communications protocol, widely used for controlling multimedia commu-
nication sessions such as voice and video calls over Internet Protocol (IP) networks. The protocol defines the messages
that are sent between endpoints, which govern establishment, termination and other essential elements of a call.
Static IP Address: A static IP Address has been assigned manually and is permanent until it is manually removed. It is not
subject to the Lease limitations of a Dynamic IP Address assigned by the DHCP Server.
WAN: Wide Area Network. A WAN is a network comprising a large geographical area like a state or country. The largest
WAN is the Internet.

Features Overview
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC
outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
4
N.C. (Gray)
N.O. (Yellow)
COM. (Blue)
Optional 2 Amp Relay
Output Contacts
(2A@30VDC/ 250VAC max)
3 Gel-Filled Butt
Connectors (included)
- Black
+ Red
Black
Black
- Black
+ Red
LED
Help Switch
Info Switch (optional)
Speaker
Microphone
MAC Address Label: The
MAC address is aunique 12
digit number used by routers
to send network traffic to the
correct IP address.
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect
to your LAN via RJ45 plug
and CAT5 or greater twisted
pair wire.
Yellow Network Status LED:
Lights steady to indicate power
and data link. Blinks to indicate
network activity.
Green Unit Status LED
Rear (PCB) View of E-10/20/30-IP Entry Phone
Red
Red
White
White
Future
Use
MAC:
18E80FXXXXXX
asdesaxtff
(Power typically not
required for gate controllers)
Doorstrike /
Magnetic Lock
120V AC
Connect to Optional
Doorstrike, Mag Lock,
Gate Controller, etc.
(not
connected)
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a max-
imum insulation of 0.082 inches. Cut off stripped wire ends before terminating.

Installation and Specifications
5
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC
outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
A. Mounting the E-10-IP, E-10-IP-EWP, E-30-IP and E-30-IP-EWP
The E-10-IP and E-30-IP are designed to be flush mounted to the included 4” x 4” x 2” deep plastic rough in box or sur-
face mounted using an optional Viking model VE-5x5. Note: The E-10-IP and E-30-IP will NOT mount to a standard
double gang box. The plastic rough in box (part # 259576) may be purchased separately. Go to www.vikingelectron-
ics.com and click on “Spare Parts”.
Front View of Optional
VE-5x5 (not included)
2.25”
Condensation
Drain Hole
*1/8" thick foam
gasket (included)
5.14”
5.22” 3.25”
Call
4.0"
Rear View of VE-5x5 (not included)
Push to Call Button
(4) 6-32 X 3/4” stainless steel, flat
head, hexdrive, screws (included)
Condensation Drain Hole
5.0”
Typical
(4) 0.38” diameter (for gooseneck mounting)
(4) 0.2 x 0.43 slots for double gang box
(2) 0.2 x 0.43 slots for single gang box
(1) .74" dia
3.0” 3.3”
3.0”
2.1”
Wall Stud
Front View of Plastic
Rough-In Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
The optional VE-5x5 Surface Mount Box is designed to be
surface mounted to a single gang box, double gang box
or VE-GNP gooseneck pedestal (shown right). For more
information on the VE-5x5 and VE-GNP, see DOD# 424.
* Note: Peel off paper liner and adhere
gasket to the back of the faceplate, center-
ing it over the four corner mounting holes.
Caution: For rough surfaces
(ie: brick, stucco, etc.) additional
caulking may be required.
B. Mounting the E-20-IP and E-20-IP-EWP
The E-20-IP and E-20-IP-EWP are designed to be surface mounted to a single gang box (not included), a standard 4”
x 4” electrical junction box (not included), or directly to a wall or flat sided post. Caution: For rough surfaces (ie: brick,
stucco, etc.) additional caulking may be required.
UP
Call
VIKING©
3.40"
1.55"
3.40" 2.35" 3.30"
Front view of the
E-20-IP/E-20-IP-EWP Back Panel of the E-20-IP/E-20-IP-EWP Side view of the E-20-IP/E-20-IP-EWP
To open the speaker box, remove the
two separate screws from the cover.
Mount back panel to a wall, a single
gang box or a 4”x4” junction box with
the arrow pointing up. Note: For
outdoor applications apply a bead of
caulk between back panel and wall.
Attach the cover to the
base with the two included
screws as shown.

6
C. Replacement IP Board Kit (Model E-1600-53A-IP)
This is a board (PCB) only kit, no chassis is included. This kit can be used to convert any Viking E-10A or E-30 analog
phone to a VoIP version. The kit can also be used to replace a damaged IP board in the field. This kit comes in standard
and EWP version. The optional EWP version features foam rubber gaskets and boots, sealed connections, gel-filled
butt connectors, as well as urethane or thermal plastic potted circuit boards, see DOD# 859 for more information.
(2) 0.156
diameter
type 2
mounting
holes
0.15 (0.19 EWP)
3.50 (3.58 EWP)
3.20
2.0
(2.04
EWP)
0.63
(0.67
EWP
1.5 2.63
(2.71
EWP)
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
Black
Red
Black
Black
Red**
Red**
White
White
Black
Red
- Black
+ Red
Black
Black
Red**
Red**
White
White
- Black
+ Red
LED
Call Switch
Info Switch (not used)
Speaker
Mic
Connector and Wires
from Existing Standard
E-30 Analog
Entry Phone
FIGURE 1
Replacement Cable Assembly
(included )
- OR -
Replacement connectors, wires and
butt connectors for use when replacing
E-10A/EWP or E-30-EWP circuit boards.
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller, etc.
** Note: These two red wires are only
used on units with an Info button. When
installing on a single button unit, cut off
these two red wires and discard.
8 1 10 1
MAC:
18E80FXXXXXX
asdesaxtff
Step 1. Cut wires from J1 (10 pin connector) and J2 (2 pin connector).
Step 2. Remove the two #6 phillips screws fastening the circuit board.
Step 3. Cut off any stripped wire ends from the replacement cable.
Step 4. Using the supplied gel-filled butt connectors, connect corresponding wires from replacement cable to the previously cut
wires from the LED, Call switch, Speaker and Microphone. See FIGURE 1 above for wire color and polarity.
How to Replace Analog E-10A, E-10A-EWP or E-30-EWP Circuit Boards:
E-1600-53A-IP Board Specifications
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (3)
optional gel-filled butt connectors, (10) addi-
tional gel-filled butt connectors included with
EWP version only.
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum in-
sulation of 0.082 inches. Cut off stripped wire ends before terminating.

7
PC Requirements
• IBM compatible personal computer with:
Windows 2000 (service pack 4 or higher)
Windows XP (service pack 2 or higher)
Windows Vista (SP2 or newer), 32 or 64 bit versions
Windows 7
Windows 8
• Adobe Acrobat Reader 8 or higher
• E-10/20/30-IP hardware
• Available LAN with PoE (class 1, <4 watts)
• Ethernet cable ( CAT5 min.)
• 1 MB minimum free hard drive space for installation
• 16MB of free physical RAM
Typical Installation on SIP Based VoIP Phone System
Optional
PoE Injector
(If VoIP PBX does
not have PoE) Optional
Switch / Hub
(Extends range of cable, keeps
1 Gbps network speed for other
equipment on network)
SIP VoIP PBX
or
PC with
SIP Server
Software
100m (328 ft) max*
Viking
supplies
Customer’s
Responsibility
Internet
10/100 Mbps
Maximum
Viking
E-30-IP
Entry Phone
* Note: A PoE extender can be used for an additional 100 meters per extender. For longer runs (up to 2 km / 1.2 miles)
a ethernet to ber media converter can be used.
PC Programming
A CD is included with each E-10/20/30-IP VoIP Entry phone. The CD contains the application “Viking VoIP Phone Programming” used to
program the unit using a PC running Windows 2000, XP, Vista, Windows 7, or Windows 8 (see System Requirements above). The PC must
be connected to the same LAN as the E-10/20/30-IP VoIP phone. Install the application on your PC by placing the CD into your PC’s drive.
Click “I Accept” on the bottom of the first screen, then select “Viking VoIP Phone Programming” and click the “Install” button. Follow the
directions on the screen. If you are reinstalling the Viking VoIP Phone Programming software you must uninstall the original version first via
“Add and Remove Programs”. To start the Viking VoIP Phone Programming application, click on the Viking VoIP Phone Programming icon on
your desk top. The Main screen will appear, allowing the user to program any E-10/20/30-IP phone connected to that LAN.
A. Manually Muting SIP/Network Failure Alarm Beeps (3 beeps repeated every 30 seconds)
With the unit connected and powered (Green LED on and Yellow LED off or blinking) it will output 3 beeps every 30 seconds and
turn the Call/Call Connected LED on and off once per second indicating a SIP registration failure, failure to ping gateway or Ethernet
connection failure. You can manually disable the beeps by pressing and holding the Call button for 5 seconds (2 beeps will then be
heard) or by clicking the “Mute Alarm Until Next Failure” tab in the Viking VoIP programming software. The LED will continue to flash
allowing you to trouble shoot the failure.
B. Configuring the E-10/20/30-IP Network Settings
Step 1. Open the “Viking VoIP Phone Programming” software on a windows PC that is connected to the same LAN as the E-10/20/30-IP phone
to be programmed. The default static IP Address is: 192.168.154.1
Step 2. The window in the upper left corner of the menu will show you each E-10/20/30-IP phone that is connected to that LAN. Select the unit
with the same MAC address shown on the label located on the top of the Ethernet connector on the E-10/20/30-IP phone.
Step 3. Click the “Connect” button. If a pop up window appears, enter the unit’s security code (factory set to 845464) then click the “OK” button.
Step 4. The program will then read and display the E-10/20/30-IP phone’s IP and programming settings.
Step 5. After adjusting the IP and phones settings, click the “Write” button under each column of settings to send the programming commands
to the connected unit.

8
C. Manually Resetting All Network Parameters to Factory Default
Step 1. Power down the E-10/20/30-IP phone by disconnecting the RJ45 plug.
Step 2. Press and hold the HELP/CALL button, then reconnect the RJ45.
Step 3.
Continue to hold the button until you hear 2 beeps, (approximately 6 seconds). Continue to hold the button until you hear 4 more
beeps, approximately 6 seconds later, then release the button. The “Call Connected” LED will remain off for the first 3 seconds, flash
slowly for 3 seconds (2 beeps), fast flash for 6 seconds (4 beeps), then light steady indicating when to release button.
Step 4. The unit should continue to output double beeps and slowly flash the LED indicating all Network Parameters are now reset to factory
default. The default static IP Address is: 192.168.154.1
Step 5. You must now power cycle the unit by momentarily disconnecting the RJ45.
Step 6. You will be required to re-enter your initial network settings prior to any touch tone programming, see section A on page 9.
Touch Tone Programming
A. Accessing the Touch Tone Programming Mode
1. Using the Security Code to Enter Programming
Step 1. From a touch tone phone call the E-10/20/30-IP phone you would like to program.
Step 2. When the E-10/20/30-IP phone answers, enter the 6-digit security code (factory set to 845464, see section B). A double beep
should then be heard indicating you have entered the programming mode.
Step 3. You can now touch tone program the Quick Programming Features listed on page 9.
2. Manually Resetting the Security Code to Enter Programming
Step 1. Power down the E-10/20/30-IP phone by disconnecting the RJ45 plug.
Step 2. Press and hold the CALL button, then reconnect the RJ45.
Step 3. Continue to hold the button until you hear 2 beeps, (approximately 6 seconds). Then release the button. The “Call Connected” LED
will remain off for the first 3 seconds, flash slowly for 3 seconds then fast flash (after 2 beeps) indicating when to release button.
Step 4. The security code is now reset to 845464 (factory default).
Step 5. You can now enter touch tone programming by following the steps in section 1. Using the Security Code, above.
Step 1. Access programming as shown in Programming section A.
Step 2. Enter 123456 #19.
Step 3. Hang-up.
B. Security Code (#19)
The security code allows the user/installer to program the E-10/20/30-
IP phone. The factory set security code is 845464 (V-I-K-I-N-G). It is
recommended that the factory set security code be changed. Note: The
security code must be 6 digits and cannot include a
Q or a #.
Example: To store 123456 as the security code (shown right).

9
Quick Programming Features (after accessing the Touch Tone Programming Mode)
DESCRIPTION DIGITS + MEMORY
LOCATION
First speed dial number 0-20 digits + #00
Second speed dial number 0-20 digits + #01
Third speed dial number 0-20 digits + #02
Fourth speed dial number 0-20 digits + #03
Fifth speed dial number 0-20 digits + #04
To clear any speed dial number (no digits) + #00 - #04
Talk/Listen Delay (.1 to .9 sec, factory set to .5 sec) 1 digit (1-9) + #11
Call Length Time Out (0 to 9 min, 0 = disabled, factory set to 3 min) 1 digit (0-9) + #12
Lap Counter (0 to 9, 0 = disabled, factory set to 0) 1 digit (0-9) + #16
Dial Next Number on Ring No Answer (0 or 1 = disabled, 2 - 9 = number of rings, factory set to 7) 1 digit (0-9) + #17
Dial Next Number on Busy (0 or 1, 0 = disabled, factory set to 1/enabled) 1 digit (0 or 1) + #18
Security code (factory set to 845464) 6 digits (0-9) + #19
Identification number (factory set to 987654) 6 digits (0-9) + #20
Access Code (1-6 digits, blank = disabled, factory set to 123456) 1-6 digits (0-9) + #21
Mic volume (0-9, 0 = ANC, factory set to 5) 1 digit (0-9) + #22
Speaker Volume (0-9, factory set to 5) 1 digit (0-9) + #23
Relay Activation Command ( 1 or 2 digits, QQQQ = QQ,Q#Q# = ##, 0-9 or 00-99, factory set to
QQ) (Relay Mode must be set to 0 = Door Strike) 1 or 2 digits + #24
Relay Activation Time (2 digits, 00-99 sec, 00= 0.5 sec, factory set to 05) 2 digits (00-99) + #25
Relay Mode (0 = Door Strike, 1 = Outbound Call, 2 = In/Outbound Call, 3 = Doorbell, 4 = LV-1K
Control, factory set to 0) 1 digit (0-3) + #26
Relay Activation Tone (Buzz) Volume (1 digit 0-3, 0 = off, factory set to 3) 1 digit (0-3) + #27
Audio Detection Sensitivity (1-9, 1 = min, 9 = max, factory set to 5) 1 digit (1-9) + #28
In-Band Call Progress Detection (0 or 1, 0 = OFF, 1 = ON, factory set to 0) 1 digit (0 or 1) + #29
“Call Connected” LED Control (1 or 2, 1 = Automatic, 2 = Called Party Control / Qentered to light
LED, factory set to 1) 1 digit (1 or 2) + #30
Speaker Mode (0, 1 or 2, 0 = OFF/Silent Monitor, 1 = ON, 2 = OFF Until Answered, factory set to 1) 1 digit (0-2) + #31
LED Mode (0, 1 or 2, 0 = OFF/Silent Monitor, 1 = Entry Phone, 2 = Emergency Phone, factory set to 1) 1 digit (0-2) + #32
Auto Answer/Ring (0, 1 or 2, 0 = OFF, 1 = ON, 2 = OFF with Ringer Enabled, factory set to 1) 1 digit (0-2) + #33
DESCRIPTION ENTER DIGITS
Diagnostic tones (used to check mic and speaker operation) Q0
Enable Alternate Switch Action (factory setting) Q1
Disable Alternate Switch Action Q2
Enable Latching Commands (factory setting) Q6
Disable Latching Commands Q7
To add a Qat any point in the dialing string QQ
To add a # at any point in the dialing string Q#
Reset all Quick Programming Features to factory default settings ###

10
Programming Features
To Program the E-10/20/30-IP Phone... Step 1 Step 2
...to store 555-1234 as the first emergency speed dial
number
Enter Programming
(see A. Accessing the Touch Tone
Programming Mode, page 10)
Enter digits:
5 5 5 1 2 3 4 # 0 0
...to clear the first emergency speed dial number
Enter Programming
(see A. Accessing the Touch Tone
Programming Mode, page 10)
Enter digits:
# 0 0
A. Speed Dial Numbers (memory locations #00 - #04)
Note: Up to 32 digits can be stored in each dial position via touch tone programming, up to 255 characters via PC programming. Touch
tone
Q and #count as single digits.
The speed dial number programmed in location #00 is the number that is dialed when
the ”CALL” button is first pressed. Additional speed dial numbers will be dialed when
there is no answer or a busy signal is detected and the next number redial features are
activated. To program, enter the desired speed dial number followed by the location
number (#00 - #04). To clear a speed dial location, simply enter the memory location
(#00 - #04) alone. The E-10/20/30-IP phone is factory set with no speed dial number
programmed.
To Program: Enter:
QQQ
#Q#
0, 1, 2 .... 9 0, 1, 2 .... 9
B. Speed Dial Programming Examples
This feature selects switching time between talk and listen modes (VOX switching time).
Use chart at the right.
* Note: The factory default is .5 seconds.
2. Talk / Listen Delay (#11)
This feature selects the maximum length of time that calls can be connected. Program-
mable in increments of 1 minute up to a maximum of 9 minutes (Touch Tones 1 - 9). Pro-
gram 0 in this location to disable the call length time out. With the call length disabled, the
E-10/20/30-IP phone must rely on a CPC signal, busy signal, silence or return to dial tone
to hang-up. Use chart at the right.
* Note: The factory default is 3 minutes.
3. Call Length Time Out (#12)
Touch
Tone
Talk/Lis-
ten Delay
1 .1 sec
2 .2 sec
3 .3 sec
4 .4 sec
5 .5 sec *
6 .6 sec
7 .7 sec
8 .8 sec
9 .9 sec
Touch
Tone
Call Length
Time Out
0 Disabled
1 1 min
2 2 min
3 3 min*
4 4 min
5 5 min
6 6 min
7 7 min
8 8 min
9 9 min
1. Speed Dial Numbers (#00 - #04)