Viking E-60-SS-IP User manual

PRODUCT MANUAL
Designed, Manufactured and Supported in the USA
COMMUNICATION & SECURITY SOLUTIONS
E-60-IP Series
Double Gang Mount
VoIP Entry Phones
October 29, 2015
VIKING
Features Applications
Specifications
www.vikingelectronics.com
Information: [phone]
VoIP Entry Phones in 4 Attractive Finishes that
Mount in Standard Double Gang Electrical Boxes
• Compact: Front panel is the size of a typical double gang mid-size wall plate
• Mounting: Flush mounts in a double gang electrical box (2.25” deepx 3.65”
wide x 2.84” tall minimum) or surface mounts in a Viking VE-5x5 (not in-
cluded, see DOD# 424) for mounting to a wall, post or VE-GNP Gooseneck
Pedestal (EWP recommended)
• Available in 4 standard faceplate finishes: Brushed Stainless Steel, Oil
Rubbed Bronze, Textured Black and Satin White
• PNL-60 faceplates: Replacement faceplates with matching screws available
in all four standard finishes
• Self diagnostic reports via email (testing com, mic, speaker & switch)
• Automatic polling and programming software included
• 2 Amp relay contacts for door/gate or SL-2 strobe light control
• Blue LED indicator
• SIP compliant (see pg 2 for list of compatible IP-PBX phone systems)
• PoE powered (class 1, <4 watts)
• Automatic Noise Canceling (ANC) feature for proper operation in noisy
environments
• VoIP eliminates the need for “Push to Talk” mode
• Network downloadable firmware
• Handsfree operation
• 304 stainless steel prevents corrosion on the stainless steel models
• Programmable to dial up to 5 numbers on busy or ring no answer
• Cycles through backup phone numbers on busy or no-answer
• Optional Enhanced Weather Protection (EWP), EWP products are designed
to meet IP66 Ingress Protection Rating, see DOD# 859
• Hangs up on busy signal, time-out or touch tone command
• Remotely programmable
• Extended temperature range (-40°F to 140°F)
• Volume adjustments for microphone and speaker
• Optional PB-100 Polling System available (DOD# 232)
• Optional SL-2 or BLK-4-EWP strobe light kit available (DOD# 242/653)
Power: PoE class 1 (<4 watts)
Dimensions: Faceplate: 123.8mm x 125.4mm x 4.3mm (4.875” x
4.938” x 0.17”), Phone: 72mm x 46mm x 42mm (2.84” x 1.8” x
1.65”)
Shipping Weight: 0.55 kg (1.2 lbs)
Operating Temperature: -40°C to 60°C (-40°F to 140°F)
Humidity - Standard Products: 5% to 95% non-condensing
Humidity - EWP Products: Up to 100%
Audio Codecs: G711u, G711a, G722
Network Compliance: IEEE802.3af PoE, SIP 2.0 RFC3261,
100BASE-TX with auto cross over
Connections: (1) RJ45 10/100 Base-T, (3) gel-filled butt connec-
tors
Installation requires the assistance of a Network Administrator / IT Technician.
!
The E-60-IP Series are compact, vandal resistant VoIP Entry Phones designed to
provide quick and reliable handsfree communication for SIP VoIP phone systems
with PoE. The E-60-IP Series entry phones can be programmed from any Touch
Tone phone or PC on the same LAN. The entry phones can dial up to 5 program-
mable numbers.
The E-60-IP’s compact size allows it to be mounted in a standard double gang
electrical box. The E-60-IP is available in four different attractive finishes to match
your door hardware, light fixtures, etc. Replacement E-60 faceplates (PNL60) can
be purchased separately and are available in all four standard finishes. The E-60-
IP’s blue LED continually provides light for locating the push button in dark loca-
tions, flashes during dialing and automatically lights again when the call is
answered. All programming parameters, including phone numbers and location
numbers, are stored in non-volatile memory, requiring no batteries. All units are
PoE powered.
For outdoor installations where the unit is exposed to precipitation or condensa-
tion, the E-60-IP Series entry phones are available with Enhanced Weather Pro-
tection (EWP). EWP products feature foam rubber gaskets and boots, sealed
connections, gel-filled butt connectors, as well as urethane or thermal plastic pot-
ted circuit boards. For more information, see DOD# 859.
• Gate Entrance
• Parking ramps/lots
• ATM machines
• Medical centers
• Lobbies
• Entryways
• Stadiums
• Convention centers
• Public access areas
E-60-SS-IP
“Brushed Stainless Steel”
(similar to brushed nickel)
Shown with optional VE-5x5 surface
mount box & VE-LIGHT (not included)
E-60-BN-IP
“Oil Rubbed Bronze”
(satin dark brown powder
paint with fine copper metallic)
E-60-WH-IP
“White”
(satin white powder paint)
E-60-BK-IP
“Black”
(fine texture black powder paint)

Viking VoIP SIP System Compatibility List
NOTE: Exclusion from this list means only that compatibility has not been verified, it does not mean
incompatibility.
2
For detailed configuration instructions for certain vendors below, see Configuring Viking VoIP Phone
and SIP Servers,DOD# 944.
Vendor
Infrastructure Class
Softswitch PBX Proxy SBC
(session border
controller)
Service
Provider
3COM VCX X
3CX X
Aastra X
Asterisk X
Atcom X
Avaya IP Office X
BlueBox X
Brekeke X
Callcentric X
Cisco Unified Communications Manager (CUCM) X X
Cisco Unified Communications Manager Express
(CUCME) XX
Freeswitch X
Grandstream X
Interactive Intelligence X X
iptel.org X
Kamailio X X
MetaSwitch XX
NEC X
OfficeSIP X
OpenSIPS X
Panasonic (with SIP Extension Card) X
Samsung Communications Manager (SCM) X X
ShoreTel X
Siemens Communications Server (SCS) X
SIP Express Router (SER) X X
sip.antisip.com X
Snom PBX X
Sonus X
Switchvox X X
Teksip X
Toshiba X
VoIP.ms X

Definitions
3
Client: A computer or device that makes use of a server. As an example, the client might request a particular file from the server.
DHCP: Dynamic Host Configuration Protocol. In this procedure the network server or router takes note of a client’s MAC address and
assigns an IP address to allow the client to communicate with other devices on the network.
DNS Server: A DNS (Domain Name System) server translates domain names (ie: www.vikingelectronics.com) into an IP address.
Ethernet: Ethernet is the most commonly used LAN technology. An Ethernet Local Area Network typically uses twisted pair wires to
achieve transmission speeds up to 1Gbps.
Host: A computer or device connected to a network.
Host Name: A host name is a label assigned to a device connected to a computer network that is used to identify the device in various
forms of network communication.
Hosts File: A file stored in a computer that lists host names and their corresponding IP addresses with the purpose of mapping addresses
to hosts or vice versa.
Internet: A worldwide system of computer networks running on IP protocol which can be accessed by individual computers or networks.
IP: Internet Protocol is the set of communications conventions that govern the way computers communicate on networks and on the In-
ternet.
IP Address: This is the address that uniquely identifies a host on a network.
LAN: Local Area Network. A LAN is a network connecting computers and other devices within an office or building.
Lease: The amount of time a DHCP server reserves an address it has assigned. If the address isn’t used by the host for a period of
time, the lease can expire and the address can be assigned to another host.
MAC Address: MAC stands for Media Access Control. A MAC address, also called a hardware address or physical address, is a unique
address assigned to a device at the factory. It resides in the device’s memory and is used by routers to send network traffic to the correct
IP address. You can find the MAC address of your E-60-IP phone printed on a white label on the top surface of the PoE LAN port.
Router: A device that forwards data from one network to another. In order to send information to the right location, routers look at IP Ad-
dress, MAC Address and Subnet Mask.
RTP: Real-Time Transport Protocol is an Internet protocol standard that specifies a way for programs to manage the real-time transmission
of multimedia data over either unicast or multicast network services.
Server: A computer or device that fulfills requests from a client. This could involve the server sending a particular file requested by the
client.
Session Initiation Protocol (SIP): Is a signaling communications protocol, widely used for controlling multimedia communication sessions
such as voice and video calls over Internet Protocol (IP) networks. The protocol defines the messages that are sent between endpoints,
which govern establishment, termination and other essential elements of a call.
Static IP Address: A static IP Address has been assigned manually and is permanent until it is manually removed. It is not subject to the
Lease limitations of a Dynamic IP Address assigned by the DHCP Server. The default static IP Address is: 192.168.154.1
Subnet: A portion of a network that shares a common address component. On TCP/IP networks, subnets are defined as all devices
whose IP addresses have the same prefix. For example, all devices with IP addresses that start with 100.100.100. would be part of the
same subnet. Dividing a network into subnets is useful for both security and performance reasons. IP networks are divided using a subnet
mask.
TCP/IP: Transmission Control Protocol/Internet Protocol is the suite of communications protocols used to connect hosts on the Internet.
TCP/IP uses several protocols, the two main ones being TCP and IP. TCP/IP is built into the UNIX operating system and is used by the
Internet, making it the de facto standard for transmitting data over networks.
TISP: Telephone Internet Service Provider
WAN: Wide Area Network. A WAN is a network comprising a large geographical area like a state or country. The largest WAN is the In-
ternet.
Wireless Access Point (AP): A device that allows wireless devices to connect to a wired network using Wi-Fi, or related standards. The
AP usually connects to a router (via a wired network) as a standalone device, but it can also be an integral component of the router itself.
Wireless Repeater (Wireless Range Extender): takes an existing signal from a wireless router or access point and rebroadcasts it to
create a second network. When two or more hosts have to be connected with one another over the IEEE 802.11 protocol and the distance
is too long for a direct connection to be established, a wireless repeater is used to bridge the gap.

Features Overview
MAC:
18E80FXXXXXX
asdesaxtff
N.C. (Gray)
N.O. (Yellow)
COM. (Blue)
Optional 2 Amp Relay
Output Contacts
(2A@30VDC/ 250VAC max)
3 Gel-Filled Butt
Connectors (included)
- Black
+ Red
Black
Black
- Black
+ Red
LED
Help Switch
Info Switch (optional)
Speaker
Microphone
MAC Address Label: The
MAC address is aunique 12
digit number used by routers
to send network traffic to the
correct IP address.
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect
to your LAN via RJ45 plug
and CAT5 or greater twisted
pair wire.
Yellow Network Status LED:
Lights steady to indicate power
and data link. Blinks to indicate
network activity.
Green Unit Status LED
Rear (PCB) View of E-60-IP Entry Phone
Red
Red
White
White
(Power typically not
required for gate controllers)
Doorstrike /
Magnetic Lock
120V AC
Connect to Optional
Doorstrike, Mag Lock,
Gate Controller, etc.
(not
connected)
Push Button Switch: Push to
initiate call, push again to
disconnect. Solid 316 stainless
steel internally sealed per IP67.
Speaker Screen: Speaker
screen with 0.018" wide slots to
prevent punctures from
paperclips, etc.
Faceplate Material: 18 gauge
304 stainless steel. The SS model
has a #4 brushed finish, the BK,
BN and WH models have a
powder painted finish.
Speaker: Mylar speaker with
rubber gasket to maintain
water-tight seal and eliminate
water deterioration.
Mounting Screws: (4) 6-32 x
3/4" Marine grade 316 stainless
steel, flat head, 5/64" hexdrive
screws (included).
Blue Call LED: Lights steady to
help locate the button in low light,
flashes during dialing, then lights
steady when answered.
Microphone: Omni-directional
microphone with protective
water-resistant cloth.
Front View of the E-60-IP Entry Phone
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a max-
imum insulation of 0.082 inches. Cut off stripped wire ends before terminating.
4

Installation
The E-60-IP is designed to be flush mounted into a standard double gang rough-in box with minimum inside dimensions of
2.25” deep x 3.65” wide x 2.84” tall. The E-60-IP can also be surface mounted using a Viking VE-5x5 for mounting to a wall,
post or Viking model VE-GNP gooseneck pedestal, EWP model recommended (not included, see DOD# 424). WARNING:
Do NOT use a typical “wet location box” as not all styles seal properly with the E-60-IP faceplate.
Step 1.
Front of box should stick out approximately ½" from front surface of wall stud (this may vary depending on the walls
sheathing and siding thickness). Caution: Rough-In box must be mounted LEVEL and must NOT stick out beyond the
front surface of siding.
Step 2. To maintain a vapor barrier on outside wall applications (EWP model), caulk around the box, filling any gaps between
the box and the rough opening. Apply caulk to any holes in the box around wires, etc.
Step 3.
When installing siding cut a hole just large enough for the Rough-In box opening. Caution: Too large of a hole can cause
plate misalignment and compromise the gasket seal. Note: When mounting to 4 inch or less horizontal lap siding, a
siding mounting block can be used. Contact siding installer for the correct mounting block. Note: A side mounting block
is recommended when mounting to vinyl siding.
Step 1. Make sure mounting location is free of wall studs, wires, etc.
Step 2.
Place rough-in box LEVEL against siding. Trace outline of box onto siding. Note: When mounting to 4 inch or less hor-
izontal lap siding, a siding mounting block can be used. Contact your siding Installer for the correct mounting block part
number. Note: A siding mounting block is recommended when mounting to vinyl siding.
Step 3. Cut a hole through the siding and wall sheathing just large enough for the rough-in box. Caution: Too large of a hole can
cause plate misalignment and compromise the gasket seal.
Step 4. The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed and mounted flush
against wall sheathing when mounting on aluminum, steel or vinyl siding.
Step 5.
When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets can be used to secure
the rough-in box. When mounting to surfaces thicker than 5/8 inch, four standard flat head dry wall screws can be used
to secure the Rough-In box through its mounting ears.
Step 6. To maintain a vapor barrier on outside wall applications (EWP model), caulk around the box, filling any gaps between
the box and the rough opening. Apply caulk to any holes in the box around wires, etc.
A. New Construction Flush Mounting
B. Old Work / Remodel Flush Mounting (Using an Allied Molded 9312 Rough-In Box)
A Viking model VE-5x5 can be used to surface mount an E-60-IP to a wall, post or Viking model VE-GNP Gooseneck
Pedestal (EWP model recommended), see DOD# 424 for more information on the VE-5x5 and VE-GNP. Drill a small
wire exit hole in wall. Pull wire through and seal hole around wire with putty or caulking. Route wire into the VE-5x5
box, securely screw it to wall or post and seal hole in box around wire with putty or caulking. Attach (2) junction box to
double gang adapter plates (included with E-60-IP) to top and bottom holes of the VE-5x5 prior to mounting the E-60-
IP. Note: Conduit may also be used when surface mounting wire, but should not enter through the top of the VE-5x5.
When routing wiring from above, a drip loop is required. WARNING: Do NOT use a typical “wet location box” as not all
styles seal properly with the E-60-IP faceplate.
C. Surface Mounting
5

After the rough-in box or VE-5x5 is securely mounted, caulking between the box and rough opening is completed (if re-
quired), and wires are connected, remove paper liner from faceplate gasket. While firmly holding the LED light pipe in
the faceplate, carefully slide the faceplate gasket over the back of the light pipe and press gasket to the back of the
faceplate. Push the 1-1/4" 6-32 screws through faceplate holes and small holes in gasket, the faceplate gasket should
retain the screws. Position circuit board mounting plate over screws. Align screws with double gang box bosses and
tighten face plate until gasket is fully collapsed and the push button is protruding through the clearance hole in the face
plate. Included 1/4" thick gasket will provide an adequate seal for most siding surfaces; however for rough surfaces (ie:
brick, stucco, etc.) additional caulking may be required.
D. Mounting the Faceplate
Circuit Board
Mounting Plate
(included)
1/4" Thick Foam
Faceplate Gasket
(included)
Facplate
(included)
(4) 6-32 x 1.25" Long 5/64"
Hexdrive Flathead Screws
(included)
"Old Work" Double Gang
Rough-In Box (Allied Molded
9312 box shown, not included)
WARNING: Do NOT use a wet
location box.
(4) Optional Dry Wall
Screws (not included)
Optional VE-5x5 Surface Mount Box with
black satin powder paint finish, not included
(DOD# 424). Optional VE-LIGHT kit can be
used to illuminate the faceplate when used
with a VE-5x5 (DOD# 428).
WARNING: Do NOT use a wet location box.
2.25”
5.14”
5.22” 3.25”
3.63”
3.63”
|
OR
|
(2) Junction Box to Double Gang
Adapter Plates and (4) 5/64 Hex
Drive Flat Head Screws
(included with the E-60-IP)
3.65"
wide
min.
2.84"
tall min.
*2.25"
deep
min.
** LED
Light Pipe
(included)
Rear View of VE-5x5
Surface Mount Box
(not included)
(4) 0.38” diameter holes
for gooseneck mounting
(4) 0.2 x 0.43 slots
for double gang box
(2) 0.2 x 0.43 slots
for single gang box
(1) .74"
diameter
3.0” 3.3”
3.0”
Model E-60-SS-IP
shown in an optional
VE-5x5 Surface
Mount Box and
VE-LIGHT mounted
to a VE-GNP
Gooseneck Pedestal
Other pedestal
options available,
see DOD# 424
The optional VE-5x5 Surface Mount Box
(above) is designed to be surface mounted
to a single gang box, double gang box or
VE-GNP Gooseneck Pedestal (shown right).
For more information on the VE-5x5 and
VE-GNP, see DOD# 424.
* CAUTION: Excessive wire length and/or using a rough-in box with inadequate depth can apply force to the circuit board causing
physical damage.
** IMPORTANT: Push LED light pipe into faceplate hole, then place faceplate upside down on a clean flat surface and push down
on back side of plate until light pipe is fully seated and straight. WARNING: Inserting the light pipe more than one time can cause
a loose fit.
6

E. Replacement IP Board Kit (Model E-1600-53A-IP)
This is a board (PCB) only kit, no chassis is included. This kit can be used to convert any Viking E-60 analog phone to
a VoIP version. The kit can also be used to replace a damaged IP board in the field. This kit comes in standard and
EWP version. The optional EWP version features foam rubber gaskets and boots, sealed connections, gel-filled butt
connectors, as well as urethane or thermal plastic potted circuit boards, see DOD# 859 for more information.
MAC:
18E80FXXXXXX
asdesaxtff
(2) 0.156
diameter
type 2
mounting
holes
0.15 (0.19 EWP)
3.50 (3.58 EWP)
3.20
2.0
(2.04
EWP)
0.63
(0.67
EWP
1.5 2.63
(2.71
EWP)
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
Black
Red
Black
Black
Red**
Red**
White
White
Black
Red
- Black
+ Red
Black
Black
Red**
Red**
White
White
- Black
+ Red
LED
Call Switch
Info Switch (not used)
Speaker
Mic
Connector and Wires
from Existing Standard
E-60 Analog
Entry Phone
FIGURE 1
Replacement Cable Assembly
(included )
- OR -
Replacement connectors, wires and
butt connectors for use when replacing
E-60-EWP circuit boards.
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller, etc.
3 1 10 1
Step 1. Cut wires from J1 (10 pin connector) and J2 (2 pin connector).
Step 2. Remove the two #6 phillips screws fastening the circuit board.
Step 3. Cut off any stripped wire ends from the replacement cable.
Step 4. Using the supplied gel-filled butt connectors, connect corresponding wires from replacement cable to the previously cut
wires from the LED, Call switch, Speaker and Microphone. See FIGURE 1 above for wire color and polarity.
How to Replace Analog E-60 Circuit Boards:
E-1600-53A-IP Board Specifications
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (3)
optional gel-filled butt connectors, (10) addi-
tional gel-filled butt connectors included with
EWP version only.
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum in-
sulation of 0.082 inches. Cut off stripped wire ends before terminating.
7
** Note: These two red wires are only used on units with an Info button. When installing on a single button unit, cut off these two red
wires and discard.

PC Requirements
• IBM compatible personal computer with:
Windows 2000 (service pack 4 or higher)
Windows XP (service pack 2 or higher)
Windows Vista (SP2 or newer), 32 or 64 bit versions
Windows 7
Windows 8
• Adobe Acrobat Reader 8 or higher
• E-60-IP hardware
• Available LAN with PoE (class 1, <4 watts)
• Ethernet cable ( CAT5 min.)
• 1 MB minimum free hard drive space for installation
• 16MB of free physical RAM
Typical Installation on SIP Based VoIP Phone System
Optional
PoE Injector
(If VoIP PBX does
not have PoE) Optional
Switch / Hub
(Extends range of cable, keeps
1 Gbps network speed for other
equipment on network)
SIP VoIP PBX
or
PC with
SIP Server
Software
100m (328 ft) max*
Viking
supplies
Customer’s
Responsibility
Internet
10/100 Mbps
Maximum
Viking
E-60-SS-IP
Entry Phone
* Note: A PoE extender can be used for an additional 100 meters per extender. For longer runs (up to 2 km / 1.2 miles)
a ethernet to ber media converter can be used.
PC Programming
A DVD is included with each E-60-IP VoIP Entry phone. The DVD contains the application “Viking VoIP Phone Programming” used to
program the unit using a PC running Windows 2000, XP, Vista, Windows 7, or Windows 8 (see System Requirements above). The PC must
be connected to the same LAN as the E-60-IP VoIP phone. Install the application on your PC by placing the DVD into your PC’s drive. Click
“I Accept” on the bottom of the first screen, then select “Viking VoIP Phone Programming” and click the “Install” button. Follow the directions
on the screen. If you are reinstalling the Viking VoIP Phone Programming software you must uninstall the original version first via “Add and
Remove Programs”. To start the Viking VoIP Phone Programming application, click on the Viking VoIP Phone Programming icon on your desk
top. The Main screen will appear, allowing the user to program any E-60-IP phone connected to that LAN.
A. Manually Muting SIP/Network Failure Alarm Beeps (3 beeps repeated every 30 seconds)
With the unit connected and powered (Green LED on and Yellow LED off or blinking) it will output 3 beeps every 30 seconds and
turn the Call/Call Connected LED on and off once per second indicating a SIP registration failure, failure to receive an echo reply
from pinged gateway or Ethernet connection failure. You can manually disable the beeps by pressing and holding the Call button for
5 seconds (2 beeps will then be heard) or by clicking the “Mute Alarm Until Next Failure” tab in the Viking VoIP programming software.
The LED will continue to flash allowing you to trouble shoot the failure.
B. Configuring the E-60-IP Network Settings
Step 1. Open the “Viking VoIP Phone Programming” software on a windows PC that is connected to the same LAN as the E-60-IP phone to be
programmed.
Step 2. The window in the upper left corner of the menu will show you each E-60-IP phone that is connected to that LAN. Select the unit with
the same MAC address shown on the label located on the top of the Ethernet connector on the E-60-IP phone.
Step 3. Click the “Connect” button. If a pop up window appears, enter the unit’s security code (factory set to 845464) then click the “OK” button.
Step 4. The program will then read and display the E-60-IP phone’s IP and programming settings.
Step 5. After adjusting the IP and phones settings, click the “Write” button under each column of settings to send the programming commands
to the connected unit.
8

C. Manually Resetting All Network Parameters to Factory Default
Step 1. Power down the E-60-IP phone by disconnecting the RJ45 plug.
Step 2. Press and hold the CALL button, then reconnect the RJ45.
Step 3.
Continue to hold the button until you hear 2 beeps, (approximately 6 seconds). Continue to hold the button until you hear 4 more
beeps, approximately 6 seconds later, then release the button. The “Call Connected” LED will remain off for the first 3 seconds, flash
slowly for 3 seconds (2 beeps), fast flash for 6 seconds (4 beeps), then light steady indicating when to release button.
Step 4. The unit should continue to output double beeps and slowly flash the LED indicating all Network Parameters are now reset to factory
default.
Step 5. You must now power cycle the unit by momentarily disconnecting the RJ45.
Step 6. You will be required to re-enter your initial network settings prior to any touch tone programming, see section B on page 8.
Touch Tone Programming
A. Accessing the Touch Tone Programming Mode
1. Using the Security Code to Enter Programming
Step 1. From a touch tone phone call the E-60-IP phone you would like to program.
Step 2. When the E-60-IP phone answers, enter the 6-digit security code (factory set to 845464, see section B). A double beep should then
be heard indicating you have entered the programming mode.
Step 3. You can now touch tone program the Quick Programming Features listed on page 10.
2. Manually Resetting the Security Code to Enter Programming
Step 1. Power down the E-60-IP phone by disconnecting the RJ45 plug.
Step 2. Press and hold the CALL button, then reconnect the RJ45.
Step 3. Continue to hold the button until you hear 2 beeps, (approximately 6 seconds). Then release the button. The “Call Connected” LED
will remain off for the first 3 seconds, flash slowly for 3 seconds then fast flash (after 2 beeps) indicating when to release button.
Step 4. The security code is now reset to 845464 (factory default).
Step 5. You can now enter touch tone programming by following the steps in section 1. Using the Security Code, above.
Step 1. Access programming as shown in Programming section A.
Step 2. Enter 123456 #19.
Step 3. Hang-up.
B. Security Code (#19)
The security code allows the user/installer to program the E-60-IP
phone. The factory set security code is 845464 (V-I-K-I-N-G). It is rec-
ommended that the factory set security code be changed. Note: The
security code must be 6 digits and cannot include a
Q or a #.
Example: To store 123456 as the security code (shown right).
9

Quick Programming Features (after accessing the Touch Tone Programming Mode)
DESCRIPTION DIGITS + MEMORY
LOCATION
First speed dial number 0-32 digits + #00
Second speed dial number 0-32 digits + #01
Third speed dial number 0-32 digits + #02
Fourth speed dial number 0-32 digits + #03
Fifth speed dial number 0-32 digits + #04
To clear any speed dial number (no digits) + #00 - #04
Talk/Listen Delay (VOX) (0.1 to 0.9 seconds, factory set to 0.5 seconds) 1 digit (1-9) + #11
Call Length Time Out (0 to 9 minutes, 0 = disabled, factory set to 3 minutes) 1 digit (0-9) + #12
Lap Counter (0 to 9, 0 = disabled, factory set to 0) 1 digit (0-9) + #16
Dial Next Number on Ring No Answer (0 or 1 = disabled, 2 - 9 = number of rings, factory set to 7) 1 digit (0-9) + #17
Dial Next Number on Busy (0 or 1, 0 = disabled, 1 = enabled, factory set to 1) 1 digit (0 or 1) + #18
Security code (factory set to 845464) 6 digits (0-9) + #19
Identification number (1-6 digits, blank = disabled, factory set to 987654) 0-6 digits (0-9) + #20
Access Code (1-6 digits, blank = disabled, factory set to 123456) 0-6 digits (0-9) + #21
Microphone volume (0-9, 0 = ANC, factory set to 5) 1 digit (0-9) + #22
Speaker Volume (0-9, factory set to 5) 1 digit (0-9) + #23
Relay Activation Command ( 1 or 2 digits, QQQQ = QQ,Q#Q# = ##, 0-9 or 00-99, factory set to
QQ) (Relay Mode must be set to 0 = Door Strike) 1 or 2 digits + #24
Relay Activation Time (2 digits, 00-99 sec, 00= 0.5 sec, factory set to 05) 2 digits (00-99) + #25
Relay Mode (0 = Door Strike, 1 = Outbound Call, 2 = In/Outbound Call, 3 = Doorbell, 4 = LV-1K
Control, 5 = Ring, 6 = Ring Flash, factory set to 0) 1 digit (0-6) + #26
Relay Activation Tone (Buzz) Volume (1 digit 0-3, 0 = off, factory set to 3) 1 digit (0-3) + #27
In-Band Audio Detection Sensitivity (1-9, 1 = minimum, 9 = maximum, factory set to 5, power
cycle unit after setting) 1 digit (1-9) + #28
In-Band Audio Call Progress Detection (0 or 1, 0 = OFF, 1 = ON, factory set to 0) 1 digit (0 or 1) + #29
“Call Connected” LED Control (0 or 1, 0 = Automatic, 1 = Called Party Control / Qentered to light
LED, factory set to 0) 1 digit (0 or 1) + #30
Speaker Mode (0, 1 or 2, 0 = OFF/Silent Monitor, 1 = ON, 2 = OFF Until Answered, factory set to 1) 1 digit (0-2) + #31
LED Mode (0 to 3, 0 = OFF/Silent Monitor, 1 = Entry Phone, 2 = Emergency Phone,
3 = Emergency Phone outbound only, factory set to 1) 1 digit (0-3) + #32
Auto Answer/Loud Ring (0 to 3, 0 = Disabled, 1 = Auto Answer, 2 = Loud Ring,
3 = Loud Ring with AGC, factory set to 1) 1 digit (0-3) + #33
DESCRIPTION ENTER DIGITS
Diagnostic tones (used to check mic and speaker operation) Q0
Enable Alternate Switch Action (factory setting) Q1
Disable Alternate Switch Action Q2
Enable Relay Latching Commands (factory setting) Q6
Disable Relay Latching Commands Q7
To add a Qat any point in the dialing string QQ
To add a # at any point in the dialing string Q#
Reset all Quick Programming Features to factory default settings ###
10