Viltrus Electronics MX-7 User manual

2

3
Contents
1. ABBREVIATIONS AND EXPLANATIONS...........................................................................................6
1.1 Markings.........................................................................................................................6
1.2 LED indications..............................................................................................................7
1.3 Explanations ...................................................................................................................7
2. PREFACE ................................................................................................................................................9
2.1 Symbols..........................................................................................................................9
2.2 Safety instructions ..........................................................................................................9
3. TECHNICALDATA ..............................................................................................................................11
3.1 Purpose of device..........................................................................................................11
3.2 Information on top label...............................................................................................12
3.3 Communication interfaces............................................................................................13
3.4 Protection......................................................................................................................13
3.5 Indication......................................................................................................................13
3.6 Power supply ................................................................................................................14
3.7 Construction..................................................................................................................14
3.8 Working conditions.......................................................................................................14
3.9 Safety parameters .........................................................................................................14
3.10 Other parameters...........................................................................................................14
4. SUPPORTED FUNCTIONS..................................................................................................................15
4.1 Connection and communication functions...................................................................15
4.2 Measuring functions .....................................................................................................17
4.3 Archive functions .........................................................................................................18
4.4 Alarm functions ............................................................................................................19
4.5 Meters and data collecting functions............................................................................19
4.6 Time functions..............................................................................................................19
4.7 Other functions .............................................................................................................20
5. INSTALLATION...................................................................................................................................21
5.2 Connecting....................................................................................................................21
5.3 Switching......................................................................................................................21
6. BASIC OF VILTRUSSOFTWARE........................................................................................................24
6.1 Operating principles .....................................................................................................24

4
6.2 Before connecting................................................................................25
6.3 Connecting to data logger over serial COM (device) port [Start] ................................26
6.4 Connecting over USB (device) port [Start]..................................................................27
6.5 Connecting over Ethernet and GSM [Start] .................................................................27
7. SETTING UP .........................................................................................................................................29
7.1 Set up clock [Time parameters]....................................................................................29
7.2 Analog measurements [Analog inputs] ........................................................................32
7.3 Discrete measurements [Discrete inputs].....................................................................36
7.4 Discrete outputs [Discrete outputs] ..............................................................................38
7.5 USB (device) ................................................................................................................39
7.6 Ethernet.........................................................................................................................39
7.7 GPRS/GSM ..................................................................................................................42
7.8 Serial interfaces ............................................................................................................43
7.9 Routing .........................................................................................................................49
7.10 Accounting of energy carrier meters [Communication>Connected devices] ..............56
7.11 External modules [Communication>External module>RAY-1]..................................64
7.12 Restarting......................................................................................................................68
7.13 Limits verification ........................................................................................................69
7.14 Alerts ............................................................................................................................70
7.15 Data storing to archive [Archives]................................................................................74
8. STORED DATA.....................................................................................................................................77
8.1 Loging analog input channels [Archives>Values>Analog inputs]................................77
8.2 Heat counter data [Archives>Values>Heat]..................................................................78
8.3 GAS meter data [Archives>Values>GAS]....................................................................78
8.4 Logging water data [Archives>Values>Water].............................................................79
8.5 Electricity meter data logging [Archives>Values>Electricity]. ...................................79
8.6 Discrete inputs log [Archives>Values>Discrete inputs] ...............................................80
8.7 Event logging [Archives>Values>Events]....................................................................80
9. SUPPLEMENT......................................................................................................................................82
9.1 System requirements.....................................................................................................82
9.2 Default connection values ............................................................................................82
9.3 Preparing UTP cable.....................................................................................................82
9.4 RS232 cabling...............................................................................................................83
9.5 Com port setup..............................................................................................................83

5
9.6 USB cable.....................................................................................................................85
9.7 Installing VILTRUS USB driver...................................................................................85
9.8 TCP/IP settings .............................................................................................................87

6
1. ABBREVIATIONS AND EXPLANATIONS
1.1 Markings
Xn –is a number of sockets. This information is provided for manufacturer’s purpose.
GSM –Global Standard for Mobile Communications. These interfaces are prepared for remote
connections and data bidirectional data transfer over Global Standard Mobile network.
GPRS - a packet oriented mobile data service on the 2G and 3G cellular communication
system's global system for mobile communications (GSM).
Ethernet - a family of computer networking technologies for local area networks (LANs)
commercially introduced in 1980. Standardized in IEEE 802.3, Ethernet has largely replaced
competing wired LAN technologies. These interfaces are prepared for connection LAN (Local
Area Network).
GND –ground wire contact
RS232 - the traditional name for a series of standards for serial binary single-ended data and
control signals connecting between a DTE (Data Terminal Equipment) and a DCE (Data Circuit-
terminating Equipment). It is commonly used in computer serial ports. The standard defines the
electrical characteristics and timing of signals, the meaning of signals, and the physical size and
pin out of connectors. RS232 interfaces are prepared for connection of peripheral devices
(example energy meters, data loggers, machines and etc.).
TD –contact for transfer data wire of RS232 socket
RD –contact for read data wire of RS232 socket
DTR –contact for Data Transmit Ready wire of RS232 socket
RS485 - standard defining the electrical characteristics of drivers and receivers for use in balanced
digital multipoint systems. The standard is published by the ANSI Telecommunications Industry
Association/Electronic Industries Alliance (TIA/EIA). Digital communications networks
implementing the EIA-485 standard can be used effectively over long distances and in electrically
noisy environments. Multiple receivers may be connected to such a network in a linear, multi-
drop configuration. RS485 interfaces are prepared for connection of peripheral devices (example
energy meters, data loggers, machines and etc.).
A+ –contact for positive wire of RS485 socket
B- –contact for negative wire of RS485 socket
USB –Universal Serial Bus is an industry standard, that defines the cables, connectors and

7
protocols used for connection, communication and power supply between computer and electronic
devices. USB type B socket is prepared for connection to PC (Personal Computer). USB type A
socket is prepared for connection to peripheral devices (example memory stick’s and etc.).
M-Bus - a European standard (EN 13757-2 physical and link layer, EN 13757-3 application layer)
for the remote reading of gas or electricity meters. The M-Bus interface is made for
communication on two wire, making it very cost effective.
MBUS+ –contact for M-Bus positive wire
MBUS- –contact for M-Bus negative wire
Socket –is an endpoint of a bidirectional inter-process communication flow across an Internet
Protocol-based computer network, such as the Internet
Data/Req –are protocol used by Kamstrup, for data transfer over two wires are
Data –contact for data wire
Req –contact for request wire
Current loop - are used where a device must be monitored or controlled remotely over a pair of
conductors. Only one current level can be present at any time.
CL+ –contact for current loop positive wire
CL- –contact for current loop negative wire
1.2 LED indications
Status –device status indicating LED
Output –status of power for external device indicating LED
TX/RX –data transfer/receive indicating LED
TXD –data transferring LED indicator
RXD –data receiving LED indicator
100Mbs –Ethernet High speed connection indicating LED
1.3 Explanations
“Alarm mode” – in state of alarm status Data Logger initiates an event notification for user
selected discrete input mode (Alarm mode: unconnected, connected, both events)
Central computer –server or a computer, where data can be sent.
IP address - An Internet Protocol (IP) address is a numerical label that is assigned to devices
participating in a network that uses the Internet Protocol for communication between its nodes.
TCP/IP –Transmission Control Protocol is for communication between computers, used as a

8
standard for transmitting data over networks and as the basis for standard Internet protocols.
MAC address –Media Access Control address is a unique identifier assigned to most network
adapters.
UART –An Universal Asynchronous Receiver/Transmitter is a type of “asynchronous
receiver/transmitter, a part of computer hardware that translates data between parallel a serial
forms. UART are commonly used in conjunction with communication standards such as EIA RS-
232, RS-422 or RS-485.

9
2. PREFACE
2.1 Symbols
International electrical symbol list. Some or all symbols can be used on data logger marking or
in this user manual.
Symbol
Explanation
With the CE marking on a product the manufacturer ensures that the
product conforms with the essential requirements of the applicable EC
directives.
DC (Direct Current)
Caution
Grounding
LED indicator
1
Contact number on plug
RoHS
Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment 2002/95/EC. Commonly referred to as
the Restriction of Hazardous Substances Directive or RoHS)
2.2 Safety instructions
To install and setup device, special technical knowledges are needed. Call to seller or certified
professionals to connect and setup device!
Before connecting to power supply, be sure that:
1. Data logger is not damaged (no cracks, melted, broken or exposed areas)
2. Data logger is used with right and correct thickness cables.
3. Data logger and antenna are installed indoor.
4. The data logger is intended for supply from a Limited Power Source (LPS) with current
rating of overcurrent protective device not greater than 2A
5. The highest transients on the DC secondary circuit of LPS, derived from AC main
supply, shall be less then 71V peak.
6. The associated equipment (AE): PC and PSU (LPS) shall comply with the requirements
of Standard EN 69050-1.

10
7. Data logger is dry.
8. Ambient temperature and humidity are in normal range and non-condensing.
9. Other types of devices (meters, etc.) are connected correctly by using manufacturer‘
regulations.
10. The end of stranded conductor shall not be consolidated by soft soldering and must to be
terminated
11. Device, PC and other peripherical devices are strictly connected through one double pole
breaker (current break less than 5A and space between breaker contacts more than 3mm.)
Pole breaker has to be in building ‘s wiring and in reachable place with markings
Don‘t use:
1. Device under open water (in rain and if water is splashing on data logger or
connected devices;
2. Device if enclosure, connected cables, or other connected devices are damaged;
3. External Back-Up batteries for powering data logger.
Use device by manufacturer ‘s regulations otherwise you can damage data logger or
other devices. In that case manufacturer ‘s warranty could not be obtained.
If you suspect that device doesn‘t operate correctly or has visibleviolations, disconnect
from power supplier and contact manufacturer or your distributor to check or run
maintenance.
Manufacturer does not affect and is not responsible for GSM/GPRS/Internet operators‘
provided network service pricing and costs.

11
3. TECHNICAL DATA
3.1 Purpose of device
Data logger is designed to:
•Read out data from energy resources meters (electricity, heat, water, gas);
•Measure analog (current) signal values;
•Follow status of objects;
•Form control signals;
•Store accounting and measurement data;
•Carry out initial processing of data;
•Generate reports to service personnel at the limit of deviation from the preset parameters
and status (discrete signals) change;
•Send all data through GSM/GPRS and Ethernet.
Pic 1 Data logger’s flowchart