Vinotemp WINE-MATE VINO-1500SSL Guide

w
ww ww w. .w wi in ne em ma at te e. .c co om m
WINE-MATE Split System
Installation, Operation & Care Manual
VINO1500SSL VINO2500SSL
VINO4500SSL VINO6500SSL
V
Vi in no ot te em mp p I In nt te er rn na at ti io on na al l C Co or rp p. .
w
ww ww w. .v vi in no ot te em mp p. .c co om m
READ AND SAVE THESE INSTRUCTIONS

- 1 -
TABLE OF CONTENTS
Important Safety Information…..........................................2
Features & Specifications…………………….….…………..3
Cellar Construction.…………………………….……………..7
Installer’s Instruction…………….…..….……..……………..8
Electrical Wiring…..…………….…..….……..……………..15
Temperature Control & Humidity Adjustment.………….19
Care Guide…………………………………………………….22
User’ Troubleshooting…….………………………………...23
Customer Support……………………………………………26
Warranty……………………………………………………….27

- 2 -
Important Safety Information
WARNING:
•DO NOT USE A GROUND FAULT INTERRUPTER (GFI).
•A DEDICATED 20 OR 30 AMP CIRCUIT IS REQUIRED (1500-4500SSL OR
6500SSL).

- 3 -
Features and Specifications
•Wine-Mate split cooling systems VINO1500~6500SSL are designed and
used to provide a cold temperature between 50~65 °F for a properly
insulated wine room at a normal environment.
•The wine room will maintain humidity of 50~70% RH even when the
environment becomes dry and humid. These temperatures and humilities
are optimized for long term storage of wine.
•SSL units consist of a condensing unit and an evaporator unit, and they
are connected by a liquid line and an insulated suction line.
•SSL condensing units can be located away from the evaporator units and
wine cellars as far as 50 ft, which will bring you quiet operation.
•The SSL evaporator units provide low profile and whisper quiet operation.
The evaporator units can be installed on the ceiling in a small cabinet or
room.
The dimensions and capacities are specified as follows:
MODEL EVAP UNIT
W”xD”xH” COND UNIT L”xD”xH” Btu/h, CFM
(55/90°F) CAPACITY (55/75°F) REFRIGERANT ELECTRICAL
EVAP UNIT/
COND UNIT
WEIGHT(lb)
EVAP UNIT/
COND UNIT
VINO-
1500SSL
WM-
15SFCL
16.75x14.5
x4.75
WM-150SCU
18x12x14 1500/180 150 cu ft R134a 115V-60HZ-
0.4A /115V-
60HZ-3.1A 15/30
VINO-
2500SSL
WM-
25SFCL
31.75x14.5
x4.75
WM-250SCU
18x12x14 2500/275 250 cu ft R134a 115V-60HZ-
0.4A /115V-
60HZ-5.7A 30/40
VINO-
4500SSL
WM-
45SFCL
40.25x14.5
x4.75
WM-450SCU
18x12x14 4500/460 1000 cu ft R134a 115V-60HZ-
0.8A /115V-
60HZ-6.9A 37/60
VINO-
6500SSL
WM-
65SFCL
53.75x16.5
x6.75
WM-650SCU
24x18x17 6500/575 1500 cu ft R134a 115V-60HZ-
0.8A /115V-
60HZ-12A 61/90
NOTE:
CAPACITY IS DETERMINED UNDER THE CELLAR AND AMBIENT
TEMPERATURES OF 55°F AND 75°F WITH R11 INTERIOR AND R19
EXTERIOR INSULATIONS. ANY LOWER CABINET AND HIGHER AMBIENT
TEMPERATURES WILL REDUCE THE CAPACITY.
CAUTION:
LOW AMBIENT TEMPERATURE KIT IS REQUIRED IF THE INSTALLATION
AREA WILL BE BELOW 50°F.
CAUTION:
LIQUID AND SUCTION LINES MAY DIFFER FROM WHAT ARE SHOWN
HERE, PLEASE CHECK ON THE UNITS FOR PROPER INSTALLATION.

- 4 -
NOTE:
LEAVE MINIMUM 3” CLEARANCE FOR ELECTRICAL WIRING AND
REFRIGERATION PIPING.
Parts included:
Condensing Unit (discharge and suction valves installed) + Liquid Filter + Liquid
Indicator
Evaporator Unit (liquid line solenoid valve and expansion valve installed)
Temperature Controller (4.5”LX4.5”WX3.75”D) + Air Sensor
Fig. 1 WM15~25SFCL Evaporator Unit
Fig. 2 WM45~65SFCL Evaporator Unit