Vintage view W Series User manual

W Series Wine Racks
Installation instructions for WS1 WS2, WS3, WS4 models
Included Parts
• (1) Base strip
• (1) Neck strip
• (4) or (6) mounting hole caps
• (2) Plastic Couplers
• (2) or (4) Spiral drywall
anchors
• (4) or (6) screws
• (2) toggle bolts
Required Tools
• Phillips head screw driver
• Level
Important Note: This installation guide will assist you with installing the VintageView W Series Wine Rack
(WS1-4 models) into wood-backed or drywall surfaces. These models are suitable for most 750ml bottle sizes;
use W Series Magnum Rack for Champagne storage.
If installing racks to W Series Frames, please use the install guide and hardware included with Frames.
Figure A Figure B
1. CHOOSE BOTTLE DIRECTION
Decide if you want the necks of the bottles facing left or
right, and identify the base from the neck strip (base fea-
tures wider support divots that rest lower on the rack).
2. MARK THE FIRST STRIP
Starting at least 2¾” (70mm) from adjacent wall or
other obstructions for Split or 750ml wine bottles.
Hold the first Mounting Strip in place against the
wall in desired location (Figure A). Ensure the Strip is
plump using a Level and mark the hole locations with
a Pencil. Set the Strip aside.
SCAN THE QR CODE TO FIND YOUR PRODUCT
DOWNLOAD THE FREE APP
3D-GUIDED INTERACTIVE ASSEMBLY
INSTRUCTIONS CAN BE FOUND ON BILT
®
Before you begin
• Pencil
• Tape Measure
• Drill
• 1/16” (1.6mm) Drill Bit
• 13/32” (10.5mm) Spade Bit

Instructions: W Series Wine Racks (WS1-4)
Figure E
3. MARK THE NEXT STRIP
For the second Mounting Strip location, use a level
to measure 7 1/2” (190.5mm) from one of the first
Mounting Strip holes and mark the location for the cen-
terline of the second Strip (Figure B).
Hold the second Mounting Strip in place against the
wall centered on the mounting mark. Ensure the Strip is
plumb using a Level and mark the hole locations with a
Pencil. Double check the locations are level with those
marked for the first Strip. Set the Strip aside.
If Installing racking for 375mL bottles, use 5½”
(139.7mm) for centerline.
IMPORTANT: If installing W Series Magnum or W
Series Big Bottle Racks, reference specific instructions for
proper centerline distances.
4. (OPTIONAL) MEASURE
ADDITIONAL COLUMNS
If installing multiple columns, mark the centerline for the
next Strip 5 1/2” (140mm) from the second mark, and
mark again 7 1/2” (190.5mm) for the distance be-
tween the Neck and Base Strips (Figure C).
Note: For non-standard layouts or bottle sizes such as
a Split or Half, subtract 2” (51mm) from the Centerline
to determine the distance between wine rack columns,
then proceed with respective centerline for layout out the
Neck and Bas Strips for the next column.
5. (OPTIONAL): PREPARE RACKS TO STACK
W Series Wine Racks are designed to stack, one on top
of the other. If connecting Racks vertically, remove the
Endcaps from the Strips before mounting to the wall and
replace them with supplied Couplers.
6. DETERMINE WALL SURFACE
Drill 1/16” (1.5mm) pilot holes at the marked locations
to determine if installing into drywall or wood studs/
backing.
Figure E
Figure C
Figure D
Figure F

Instructions: W Series Wine Racks (WS1-4)
7. DRILL MOUNTING HOLES
For Drywall
For the top mounting point, drill a 13/32” (10.5mm)
hole for a Toggle Bolt. For the lower two holes (one for
WS-1 models) use a Phillip’s head screw driver to screw
the Spiral Drywall Anchors in the wall until the anchor is
flush with the wall (Figure G).
For wood or stud
Skip to end of step 8.
8. HANG THE STRIPS
For Drywall
Insert one Toggle Bolt into the top mounting hole of either
the Base or Neck Strip (Figure H). With the wings of the
Expanding Nut oriented to fold toward the Bolt head,
thread the Expanding Nut onto the Bolt so that the tip of it
starts to protrude from the end of the nut.
Hold the Strip so the Bolt aligns with the top mounting
hole and gently push the Nut through the wall. Ensure the
wings have fully expanded on the back side of the wall
(Figure I).
Important: If the Expanding Nut does not fully open
behind the wall, the Mounting Strip may come out of the
wall.
Secure the bottom of the Strip using two (2) screws —
one (1) for WS1 models. Verify the Strip is Plumb and
fully tighten the Toggle Bolt using a Phillips Head Screw-
driver.
Repeat with Second Strip.
For Wood
Attach one (1) Neck Strip and one (1) Base Strip to the
wall at marked hole locations using six (6) Screws — four
(4) for WS1 models (Figure J). Ensure each Strip is Plumb
and level before fully tightening.
Figure I
Figure E
Figure G
Figure H
Figure J

Instructions: W Series Wine Racks (WS1-4)
Figure L
9. INSTALL MOUNTING HOLE CAPS
Press three (3) mounting hole caps— two (2) for WS1
models — into the ½” holes on the face of the each
Strip.
10. OPTIONAL: CONNECTING
STRIPS VERTICALLY
When stacking the Racks, connect another Strip to the
Plastic Coupler (Figure K). Ensure that the Strip is Plum
with a Level and mark the mounting holes. Then repeat
the previous steps to attach the Strip.
11. ADD WINE
Only the good stuff.
____________________________
Problems?
Try Vino Pins installation using BILT 3D intelligent instruc-
tions, visit www.vintageview.com or give us a call at
303-504-9463.
Additional Notes:
All installations into drywall require the use of collars
and alternate fasteners to properly support the Vino
Pins. Any application outside of these parameters is not
warranted by VintageView and may result in product
and/or installation failure, property damage and/or
bodily injury.
Maintenance and Care:
VintageView W Series Wine Racks should be regularly
checked for tightness. Should any Rack to be found to
be loose, remove mounting hole covers and tighten with
screwdriver to secure.
If the face of the wall surface shows signs of break-
age, discontinue use immediately until the wall may be
adequately repaired. W Series Wine Racks may be
cleaned with a damp cloth and mild dish soap. Abra-
sive pads or steel wool should NOT be used as they will
damage the finished surfaces of the parts.
Figure K