Vintage view W Series User manual

W Series Wine Rack Frame with Standoff Bracket
Installation guide for the standard W Series Frame with FCF-2WB
Included:
• (2) 2” W Series Frame Standoff
Bracket
• (4) Self-drilling Screws
Important Note:
These installation instructions will assist you with installing the VintageView W Series Frame System (10’, 12’*,
or magnum bottle congurations) with a Standoff Bracket to create a oor-to-wall installation at a 2” (51mm)
offset from the wall. This conguration is only suitable for single-sided wine rack displays. The
Standoff Bracket is also suitable for wall-to-ceiling or wall-to-wall mouning. Visit go.vintageview.com/offthewall
for limitations. * See specic notes for W Series Frame 12 installation throughout *
Fasteners:
Fasteners for securing W Series racking to the Frame is included, but hardware for oor or ceiling surfaces is
not. When installing nished W Series Frame to the oor or ceiling, please use the following recommendations
for fasteners:
Additional Components:
(sold separately unless purchasing
complete kit)
• W Series Wine Racks
• W Series Frame (10’, 12’ or
Mag models)
• W Series Backer Bar
Required Tools:
• Drill
• Phillips head drill bit
• Phillips head screwdriver
• Level
• Pencil or Marker
• Tape measure
• Metal cutting saw
• Metal le

Instructions: W Series Wine Rack Frame with Standoff Bracket
Figure A
1. IDENTIFY PROPER HARDWARE
Using the chart on the previous page, identify the proper
oor/ceiling hardware (not included) that will be needed
for your specic project. For drywall surfaces, Vinta-
geView recommends installing to joists or wood backing
when available.
2. MEASURE CEILING HEIGHT
Measure the desired location’s installation height.
3. CREATE BOTTOM FRAME SECTION
Insert two (2) Plastic Couplers into the Frame Section that
will be used for the bottom.
** 12’ Frame Adjustment **
W Series Frame 12’ comes with welded c-channels. Con-
nect the Middle Frame to the bottom Frame be rmly slid-
ing the welded c-channel of the Middle into the bottom.
4. MARK CUT LINES
With both welded Mounting Bases facing the same di-
rection, lay each W Series Frame section on the ground,
overlapping, (Figure C), so that the measurement from
one Mounting Base to the open end of the other section
equals your installation height.
Note the overlap of the top section of Frame (the side
that features a hollowed opening) at the widest part of
the Coupler. Subtract 3/8” (10mm) to account for the
thickness of the Standoff Bracket. Mark the cutline with a
Pencil (Figure D).
If the cut mark aligns with a cross member, measure and
cut 2in (51mm) off the bottom Section using a Metal Cut-
ting Saw and start the step over.
** 12’ Frame Adjustment **
Connect the Middle Frame Section to the bottom Frame
Section by rmly sliding the welded c-Channel of the Mid-
dle Frame into the Bottom Frame. The proceed to overlap-
ping with the Top Section.
5. CUT THE FRAME
Using a Metal Cutting Saw, cut the marks at the angle on
the Top Frame section (Figure E, next page). Smooth the
end of the Frame with a Metal File.
** 12’ Frame Adjustment **
Do not cut from exposed c-channel of Middle Section.
Do not use abrasive saws as they may damage the finish.
Figure B
Figure D
Figure D
Figure C

Instructions: W Series Wine Rack Frame with Standoff Bracket
6. CONNECT THE FRAME
Connect the two Sections using the supplied Couplers
(Figure F).
** 12’ Frame Adjustment **
Connect the assembled Section (Bottom and Middle
pieces already connected) to the Top Section using the
extruding metal c-channel.
7. BUILD THE RACKS
It is common to use one (1), two (2), or (3) W Series
Wine Racks on one side of the W Series Frame. If using
more than one, connect the W Series Wine Racking
by removing the two (2) Endcaps from the end of each
Wine Rack where they will connect.
Connect the Neck Strips (smaller bottle impressions)
together with the supplied Wine Rack Couplers. Repeat
with the Base Strips (larger bottle impressions).
VintageView recommends leaving a minimum of 6in
(153mm) above and below the W Series Racks when
assembled to Frame.
8. PLACE THE RACKS
Lay the connected Strips in the desired location on the
Frame (Figure I), ensuring the Neck Strips are facing in
preferred direction.
IMPORTANT: One single Wine Rack Strip must extend
12” (305mm) above and below all connection points of
the Frame assembly (Figure H).
9. SECURE THE RACKS
Attach the Racking Assembly to the Frame (Figure J)
using two (2) or three (3) Self Drilling Screws per Strip
(quantity will vary based on individual height of racking).
Figure G
Figure H
Figure F
Figure E

Instructions: W Series Wine Rack Frame with Standoff Bracket
Then press two (2) or three (3) Mounting Hole Covers
into each Strip (Figure I) section (quantity will vary based
on individual height of racking).
10. ADD BACKER BAR
Use eight (8) Self-Drilling Screws to attach two (2) W
Series Backer Bars (FCF-BACK) to the back side of the
Frame Assembly, centered over the two connections
points (Figure J). Then press eight (8) Mounting Hole
Covers over the open screw holes.
** 12’ Frame Adjustment **
Two sets of W Series Backer Bars will be needed to sup-
port all four connection points.
11. INSERT BRACKETS
Insert two (2) Standoff Brackets into the open end of the
Frame Assembly. Drill and attach the Brackets using two
(2) Self-Drilling Screws (Figure K).
12. MARK CEILING/
FLOOR MOUNTING HOLES
Place the completed Frame in desired location. Ensure it
is plumb with a level and mark the mounting holes on the
wall and oor. Set the Frame aside and pre-drill required
pilot holes based on hardware selection.
13. INSTALL THE SYSTEM
Stand the Frame Assembly in the desired location and
ensure it is plumb both front and back and side-to-side
with a level (Figure L).
Secure the Frame to the wall (Figure L) using two (2)
of the appropriate fasteners (not provided) into each
Mounting Base. Repeat into the oor using two (2) of the
appropriate fasteners (not provided).
14. ADD WINE
Only the good stuff.
Figure J
Figure L
Figure I
Figure K

Instructions: W Series Wine Rack Frame with Standoff Bracket
Problems?
Try BILT 3D intelligent instructions, visit
www.vintageview.com, or call 303-504-9463.
Maintenance and Care:
The W Series Frame should be regularly checked for
tightness. Should any rack be found to be loose, tighten
by hand until secure.
W Series steel wine racks are easy to clean. Simply wipe
with a dry cloth or use rubbing alcohol. Here are more
Dos and Don’ts….
Use
• A dry dusting cloth
• Compressed air cans
• Rubbing alcohol and a clean cloth to remove grease,
oil, or other substances
Don’t use:
• Dish soap
• Household cleaners
• Abrasive materials
• Any chemical
Improper care may void the manufacturer’s warranty.