Viozon 1S Pro User manual
X 1
Clip
X 1
Post Cap
4 / 5 / 6mm
Hex Wrench Scan QR code below for
more products from viozon
If you feel the pitching angle too tight or too loose when
adjusting the mount, please adjust the Screw.
The load weight of mount is 3.3 to 19.8lb, factory default
settings: 6.6 to 8.8lb, it will decrease gradually when
adjusting the Screw(C) by clockwise rotation, vice versa.
Place your hand on forearm
and push it hard downwards.
Pro
X 1
Laptop Plate
X 1
VESA Connector
X 6
Screws(M4)
X 6
Screws(M5)
X 1
Base Stem
X 1
Rear Arm
X 1
Forearm
Note: Once you feel the damping of
screw increases or cannot be
rotated, please stop it, avoid of
damaging the mount.
TENSION ADJUSTMENT
WEIGHT ADJUSTMENT
ADJUST SPRING ARM AT
VERTICAL DIRECTION
6MM
5MM
5MM
INSTALLATION HARDWAREARM ADJUSTMENTS
WARRANTY SERVICE
FEEDBACK
Never worried when you choose viozon products
We offer the best after-sale service to our customer,
it only takes few minutes.
And then you will get complete service such as installation
guide, technical support, new product reminder, privilege of
purchasing similar products, promotions and warranty service
from Viozon.
Viozon is focusing on high-standard products, we believe
that customers’ feedback drives us upgrading products.
Writing a review which sharing your experience will help
other customers. Also, your review will give us great
encouragement and confidence for future improvement. If
you have any questions, please feel free to contact us
without hesitation.
Share it?
Let us know with a customer review.
Just send you name and order number to
FOR HELP PLEASE CONTACT US:
to get install video
Make sure to read the manual before installation and fully
understand how to install, if you have any questions, please visit
our website or contact our service email for the help.
Please make sure the desktop could bear the weight of mount
and monitor before installation.
This product contains small parts, keep these away from
children.
Note: Please fix the inside nut
of post(B) in position before
tighten Screw(A) on the clip.
A
B
6MM
As the picture shows,
install VESA mount on
monitor. Be careful to
leave the slide clip
upwards.
VESA standard:
75*75mm ; 100*100mm
Route power and monitor
cables through the cable
clips on the upper links.
Slide the plastic cover on the rear arm upwards until it
disengages. Put cables onto the plastic cover inside. Slide the
cover downwards until it click into place.
STEP1. ATTACH MOUNT TO WORK SURFACE STEP2. ATTACH ARM TO THE POLE STEP3. ATTACH MONITOR/LAPTOP PLATE TO ARM STEP4. CABLE MANAGEMENT
WARNING
CLAMP/GROMMET MOUNT
≥0.6” - ≤2.36”
3.15”
2.36”
Install on open edge of
work surface:
For installation through a
grommet hole:
Slide the Base Stem against
work surface edge and fully
tighten clamp Screw(A).
Before inserting the Base
Stem,please detach the
Bottom Clamp(B) from the
Top Bracket(C) by loosening
Bracket Screws(A) with Hex
Wrench.
Then inserting the Base Stem
through grommet (dia.≥2.36”)
and against work surface
edge. Fully tighten Clamp
Screw.
A
A
A
C
B
a
Remove the screw from the
Forearm by the hex wrench.
As the picture shows, install
screw in order, then put
plastic cover back.
Remove the plastic cover
from rear arm.
As the picture shows, install
clip, spring arm, post cap in
order.
Insert the VESA
connector into the
groove, when heard a
click sound means done.
Note: If you want to remove
the device, please press
shrapnel (A) to remove the
device Up to extract.
INSTALLING MONITOR
INSTALLING LAPTOP PLATE
Insert the Laptop Plate into the
groove, when heard a click
sound means done.
Other Viozon Rack & Stand manuals
