Viozon OL-1S User manual

Make sure to read the manual before installation and fully
understand how to install, if you have any questions, please visit
our website or contact the televant after-service.
Kindly please make sure the desktop could bear the weight of
mount and monitor before installation.
Please use the supporting tools when installing, It is better for
installation by 2 people. Please be careful.
This product contains small parts, keep these away from children.
Scan QR code
to get install video
Scan QR code below for
more products from viozon
WARRANTY SERVICE
FEEDBACK
Never worried when you choose viozon products We offer the
best after-sale service to our customer, it only takes few minutes.
And then you will get a complete service like The installation guide,
Technical support, New product iteration, buy New similar products
in advance , promotions, and warranty service from Viozon.
Viozon is focus on high-standard product, we believe
Customer drive our product upgrades. And write a review
that sharing your experience will help other customers ,
and this will give us great encouragement and confidence.
And if you have any questions, please feel free to contact
us without hesitate.
Just send you name and order number to
Share it?
Let us know with a customer review.
US: [email protected]
EU: [email protected]
FOR HELP PLEASE CONTACT US:
Facebook: Viozon
US: [email protected]
EU: [email protected] www.vio-zon.com
WARNING
INSTALLATION HARDWARE
X 1
VESA Connector
X 1
Clip
X 1
Post Cap
X 6
Screws (M4)
X 6
Screws (M5)
4 / 5 / 6mm
Hex Wrench
X 1
Base Stem
X 1
Arm
X 1
Laptop Plate

STEP1. ATTACH MOUNT TO WORK SURFACE
CLAMP/GROMMET MOUNT
≥0.6” - ≤2.36”
3.15”
2.36”
Install on open edge of
work surface:
For installation through a
grommet hole:
Slide the Base Stem against
work surface edge and fully
tighten clamp Screw(A).
Before inserting the Base
Stem,please detach the
Bottom Clamp(B) from the
Top Bracket(C) by loosening
Bracket Screws(A) with Hex
Wrench.
Then inserting the Base Stem
through grommet (dia.≥2.36”)
and against work surface
edge. Fully tighten Clamp
Screw.
A
A
C
B
a
STEP2. ATTACH ARM TO THE POLE
As the picture shows, install clip arm post cap in order.
The Clip could be adjusted on
your desired position by loosing
the screw(A), fix it.
HEIGHT ADJUSTMENT
Note: Please fix the inside nut of
post(B) in position before tighten
Screw(A) on the clip.
A
B
Note: Open cable clip two sides.
Remove cable clip (A) from
the arm, thread cables, install
cable clip on the arm again.
A
STEP4. CABLE MANAGEMENT
Slide the plastic cover on the rear arm upwards until it
disengages. Put cables onto the plastic cover inside. Slide
the cover downwards until it click into place.
If you feel the pitching angle too tight or too loose when
adjusting the mount, please adjust the Screw.
TENSION ADJUSTMENT
6MM
5MM
5MM
ARM ADJUSTMENTS
STEP3. ATTACH MONITOR/LAPTOP PLATE TO ARM
A
Insert the VESA
connector into the
groove, when heard a
click sound means done.
Note: If you want to
remove the device,
please press shrapnel
(A) to remove the
device Up to extract.
As the picture shows,
install VESA mount on
monitor. Be careful to
leave the slide clip
upwards.
VESA standard:
75*75mm ; 100*100mm
INSTALLING MONITOR
INSTALLING LAPTOP PLATE
Insert the Laptop Plate into
the groove, when heard a
click sound means done.