Viozon ZB-3 User manual

ZB-3
Installation
Instructions
INSTALLATION HARDWARE
Scan QR code below for
more products from viozon
Scan QR code
to get install video
X 1
Pole
X 1
Base Plate
X 1
Post Cap
4 / 5 / 6mm
Hex Wrench
X 1
Adaptor
X 1
Arm (α)
X 2
Arm (β)
X 1
Tablet Holder
X 1
Ring Fill Light
X 2
Universal Ball Head
X 2
Clip
X 1
Phone Holder
X 1
Extension Rod
Accessory
X 1
Microphone Main Stand
X 1
Microphone Holder
X 1
Laptop Plate
X 4
Screw Shim
X 4
Screws (M6x18)
X 1
Parallel Connector
Slide the plastic cover on the lower link upwards until it diengages,
then remove (A).Put power and monitor cables into the plastic
cover (B). Then slide the cover downwards until click into place (C).
A
A
BC
CABLE MANAGEMENT
Remove cable clip (A) from the arm, thread cables, install cable
clip on the arm again.
Note: Open cable clip two sides.
Make sure to read the manual before installation and fully
understand how to install, if you have any questions, please visit
our website or contact the televant after-service.
Please use the supporting tools when installing. It is better be
installed by two people. Please be careful.
This product contains small parts, keep these away from children.
WARRANTY SERVICE
FEEDBACK
Never worried when you choose viozon products
We offer the best after-sale service to our customer,
it only takes few minutes.
And then you will get complete service such as installation
guide, technical support, new product reminder, privilege of
purchasing similar products, promotions and warranty service
from Viozon.
Viozon is focusing on high-standard products, we believe
that customers’ feedback drives us upgrading products.
Writing a review which sharing your experience will help
other customers. Also, your review will give us great
encouragement and confidence for future improvement. If
you have any questions, please feel free to contact us
without hesitation.
Share it?
Let us know with a customer review.
Just send you name and order number to
[email protected]
Facebook: Viozon [email protected]
FOR HELP PLEASE CONTACT US:
www.vio-zon.com
WARNING
TENSION ADJUSTMENT
If you feel the pitching angle is too tight or too loose when
adjusting the mount, please adjust the screws.
ARM ADJUSTMENTS
5MM
6MM
5MM
Scan QR code
get install video

Use screws and Screw Shim to connect the chassis to the pole.
4MM
INSTALL THE ACCESSORY TO THE MAIN POLE
INSTALL STAND BASE / POLE
As the picture shows,
use the hex wrench to
remove screws on
arm(β)
Place the microphone main stand at the inside hole of the parallel
connector, tighten the screw which is at behind of the parallel
connector. then put the microphone holder.
INSTALLING LAPTOP PLATE:
INSTALLING TABLET HOLDER:
Insert the Laptop Plate into the
groove, when heard a click
sound means done.
5MM
Remove the screws
from the adapter by the
hex wrench.
5MM
As the picture shows, put
the accessories at the
arm(α),tighten the screw.
If you want to get taller
height-using, you
could install the
extension rod between
the universal ball head
and the phone holder.
INSTALLING PHONE HOLDER:
Install the
universal ball
head at the
arm(β) at first,
then install the
phone holder.
a
Remove the screws
from the holder
adapter by the hex
wrench.
As the picture shows,
put the accessories at
the aparted arm, put
the screw back then
tighten it.
If you want to get taller
height-using, you could
install the extension rod
between the universal ball
head and the ring fill light.
INSTALLING RING FILL LIGHT:
Install the universal ball
head at the arm(β) at
first, then install the
ring fill light.
a
INSTALLING MICROPHONE HOLDER:
INSTALLING ADAPTOP:
5MM
Using the hex wrench remove the Screw(A) from the Parallel
Connector, place the Arm(β) inside, then tighten the Screw(A).
As the picture shows,
put the Clip Arm(α)
Clip Arm(β)
Parallel Connector into the Pole
cover the Post Cap ,
then, tighten the screw.
Clip
Arm(α)
Arm(β)
Arm(β)
Post Cap
Parallel Connector
Screw(A)
Scan QR code
get install video