Viozon OL-10T User manual

STEP2. ATTACH ARM TO THE POST
Wear the parallel connector (F) into the post, tighten the screw (E).
Disassemble the screw from the adaptor (A), then insert the
adaptor (A) into top of the forearm (Note: assemble the shims
between the adaptor and top of the forearm as picture), tighten
the screw of bottom.
Loose the screw (B), remove the caps of parallel connector (C),
insert two arms (D) into the post, tighten the screw and cover
the caps, cover the cap (E).
Height Adjustment
The Parallel connector (A) could
be adjusted on your desired
position by loosing the screw
(B), fix it.
The Clip (C) could be adjusted
on your desired position by
loosing the screw (D), fix it.
Note: Please fix the inside nut of post (B) in
position before tighten Screw (C) on the
Parallel connector (A).
Note: Please fix the inside nut of post (B) in
position before tighten Screw (C) on the
Clip (A).
Cap the adaptor (A) into top of the forearm (Note: cover the
black shim firstly as picture), tighten the screw of bottom.
B
C
D
F
Fix the Clip (C) to the desired position, tighten the screw (B),
then insert arm (D) into the post.
E
d
e
f
D
A
E
A
D
B
A
A
C
B
C
ABC
B
D
C
STEP1. ATTACH MOUNT TO WORK SURFACE
≥0.6” - ≤2.36”
3.15”
INSTALL ON OPEN EDGE
OF WORK SURFACE:
Slide the Base Stem against
work surface edge and fully
tighten clamp Screw(A).
A
As the picture shows,
install VESA mount on
monitor. Be careful to
leave the slide clip
upwards.
VESA standard:
75*75mm ; 100*100mm
STEP3. ATTACH MONITOR/LAPTOP PLATE TO ARM
A
Insert the VESA
connector into the
groove, when heard a
click sound means done.
Note: If you want to
remove the device,
please press shrapnel
(A) to remove the
device Up to extract.
INSTALLING MONITOR
INSTALLING LAPTOP PLATE
Insert the Laptop Plate into
the groove, when heard a
click sound means done.
Note: Open cable clip two sides.
Remove cable clip (A) from
the arm, thread cables, install
cable clip on the arm again.
A
STEP4. CABLE MANAGEMENT
Slide the plastic cover on the rear arm upwards until it
disengages. Put cables onto the plastic cover inside. Slide
the cover downwards until it click into place.
If you feel the pitching angle too tight or too loose when
adjusting the mount, please adjust the Screw.
TENSION ADJUSTMENT
6MM
5MM
5MM
ARM ADJUSTMENTS

Make sure to read the manual before installation and fully
understand how to install, if you have any questions, please visit
our website or contact the televant after-service.
Kindly please make sure the desktop could bear the weight of
mount and monitor before installation.
Please use the supporting tools when installing, It is better for
installation by 2 people. Please be careful.
This product contains small parts, keep these away from children.
X 3
Adaptor
X 10
Screws (M4)
X 10
Screws (M5)
OL-10T
X 2
VESA Connector
X 1
Laptop Plate
X 1
Post Cap
4 / 5 / 6mm
Hex Wrench
X 3
Clip
X 1
Base Stem
X 3
Arm
X 1
Parallel Connector More application:
WARNINGINSTALLATION HARDWARE
Scan QR code below for
more products from viozon
WARRANTY SERVICE
FEEDBACK
Never worried when you choose viozon products We offer the
best after-sale service to our customer, it only takes few minutes.
And then you will get a complete service like The installation guide,
Technical support, New product iteration, buy New similar products
in advance , promotions, and warranty service from Viozon.
Viozon is focus on high-standard product, we believe
Customer drive our product upgrades. And write a review
that sharing your experience will help other customers ,
and this will give us great encouragement and confidence.
And if you have any questions, please feel free to contact
us without hesitate.
Just send you name and order number to
Share it?
Let us know with a customer review.
US: [email protected]
EU: [email protected]
FOR HELP PLEASE CONTACT US:
Facebook: Viozon
US: [email protected]
EU: [email protected] www.vio-zon.com