ViSAGE VIS0481 User manual

1 of 3 pages
VIS0481 LED Multipar 18 x 5 in 1 RGBAW Operation Manual
The 5IN1 LED Multipar provides an extremely powerful light source. Controlled via digital display
through the three buttons------MODE, UP, DOWN. It can function store when it is turned off, resuming this
program when turned back on. This product has a temperature protection function, turning off automatically if
the temperature exceeds 85°C.
A Specification:
1. Weight: 6.2kg
2. Size: 330 x 270 x220mm
3: Supply: AC 120V/240V, 60HZ/50HZ
4: Consumption: 165W max
5: LEDS: 18 x 10W (RGBWA 5 in 1)
6: Beam angle: 40°
7: 3PIN female XLR socket and 3PIN male XLR socket
8: Built-in microphone
9: LED digital display
10: IR remote available (VIS0499 available separately)
Operation modes are accessed via Mode button as follows (To make the display stay on constantly press the
MODE and UP buttons at the same time. To make the display turn off after 20 seconds, press the MODE and
DOWN buttons at the same time.)
1. Static colour select mode
Press“MODE ” button to select static colour program mode. The digital display reads “C.X X”. Press “UP” or
“DOWN” to select individual colours.
2. Colour snap mode
Press“MODE” button,to select colour snap change mode. The digital display reads “J.X X”. Press UP or
DOWN to select the change speed 1-99 (from slow to quick)
3. Colour fade mode
Press“MODE” button,select colour fade mode. The digital display reads “F.XX”. Press UP or DOWN to select
fade speed 1-99 (from slow to quick).
4. Auto-run mode
Press“MODE”button,to select auto mode. The digital display reads “A.- -” The colour snap change program and
colour fade program run alternatively. The UP or DOWN buttons have no effect in this mode - running speed is
determined by the current speed of colour snap and colour fade programs.
5. Sound-active mode
Press“MODE” button to select sound-active mode. The digital display reads “S.XX”. Press UP or DOWN to
select sound sensitivity from 0-31. 0 is off, 1 is the lowest sensitivity, 31 is the highest.
6. Slave mode
Press“MODE” button to select Slave mode. The digital display reads “S.L.A.”. The UP or DOWN buttons have
no effect in this mode.
7. DMX mode
Press MODE button to select DMX mode. The digital display shows DMX address“X X X”. Press UP or DOWN
to select DMX address.You can set 512pcs address. It will flicker when there is no controller signal.

2 of 3 pages
1) DMX mode
CH No. DMX VAULE FUNCTION
CH1 000~255 Red(dim→bright)
CH2 000~255 Green(dim→bright)
CH3 000~255 Blue(dim→bright)
CH4 000~255 White(dim→bright)
CH5 000~255 Amber(dim→bright)
000~189 Dimmer(dim→bright)
190~250 Flash(slow→fast)
CH6
251~255 No function
11. Operation by IR remote :
You can also operate this product by IR remote, the maximum operating distance is 10M.
Select program Mode
Press PROG button to select static colour, snap change, colour fade or auto run mode. Each press of this button
will change to the next mode.
1. When the LED par goes into the static color select mode press “+” and “-” or button 1-9 to select the static
colours. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.
2. When the LED par goes into the snap change mode, you can press SPEED to set the color change speed and
press “+”and “-” to adjust it. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the
flash speed.
3. When the LED par goes into the colour fade mode,you can press SPEED to set the fade speed and press “+”
and “-” to adjust it. You can also press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.
4. When the LED par goes into auto run mode you can press FLASH to turn on/off flash and press “+”and “-”
to adjust the flash speed.
Sound Active Mode
Press SL/SA button to cycle between slave mode and sound active mode. Each press of this button will change
modes. When the the LED par goes into sound active mode, you can press “+” and “-” to adjust the sound active
sensitivity level.
M/S mode
Press SL/SA button to cycle between slave mode and sound active mode to choose slave mode. Each press of
this button will change modes.
Select light program mode
Press R/G/B/W/A to choose R/G/B/W/A colours, pressing “+” and “-” buttons to adjust the intensity of the
light. Press FLASH to turn on/off flash effect, pressing “+” and “-” buttons to adjust the flash speed.

3 of 3 pages
DMX MODE
Press D button to set the LED par into DMX mode.
Set ADDR
Press this button to set the DMX address or initialize the program, then the red, green, blue, white and amber
lights will flash 2~3 times. Enter the 3 digit number, for example, 1 2 3. When the red light is on, enter the first
number. After the first number is accessed the green light will come on, then enter the second number. After the
second number is accessed the blue light will come on, then enter the third number. After all three numbers are
entered, the red, green ,blue, white and amber lights will flash 2~3 times, indicating that the DMX address is
correct and the unit will enter DMX MODE automatically. If the address is wrong the red light will be on. A new
DMX address should be put in.
Black Out mode
Press “BLACK OUT” to set the LED lights power on or power off by pressing this button.