11-
Fixture Hours
Press the MENU button up to when the is blinking on the display. Press ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button.
Software version
Press the MENU button up to when the is blinking on the display. Press ENTER
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button again.
4.How To Control The Unit
You can operate the unit in two ways：
1. By master/slave built-in preprogram function
2. By DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show on the
display and move all the motors to their ‘home’position. After that the unit will be ready to
receive DMX signal or run the built in programs.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when
you want an instant show. You have to select (show 1) or (show 2) ……or
(show 19, show17~19 have to be edited by the user) show for the first unit. Its DMX
input jack will have nothing plugged into. The other units will be slave mode automatically.
4.2 DMX Controller
Use universal DMX controller to control the units, you have to set DMX address from 1 to
512 channel so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Press ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512
address. Once the address has been selected, press and keep ENTER button pressed up
to when the display stops blinking or storing automatically 8 seconds later. To go back to
the functions without any change press the MENU button again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units：
4 Channels：
4D Channels：
4C Channels：
4-
cut off the mains power immediately.
yDo not operate in dirty and dusty environment, also cleaning fixtures regularly.
yDo not allow children to operate the fixture.
yDo not touch any wire during operation as there might be a hazard of electric shock.
yAvoid power wires together arounding other cables.
yReplace fuse only with the same type.
yIn the event of serious operating problem, stop using the unit immediately.
yNever turn on and off the unit time after time.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
yDo not open the unit as there are no user serviceable parts inside. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.
yDisconnect the mains power if the fixture is not used for a long time.
yDo use original packing materials once transport it again.
yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
yDo not look directly at the LED light beam while the fixture is on.
yTo protect the machine, power off 10s rear can electrify.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of
10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is
out of the touch of people and has no one pass by or under it.
When the power supply is 110V, do not connect in series much
more than 7 units, use another mains supply for next 7 units. When
the power supply is 230V, do not connect in series much more than
14 units, use another mains supply for next 14 units.
