Vision TF40 User manual

TF40
TF20
T40
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
TREADMILL OWNER’S MANUAL

23
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
When using an electrical product, basic precautions should always be followed, including the following: Read all instructions
before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of
all warnings and precautions. If you have any questions after reading this manual, contact your authorized Vision Fitness retailer.
This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.
This treadmill has a pre-waxed belt and should never be lubricated.
Waxing the belt can cause damage that is not covered by the warranty.
IMPORTANT

4 5
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• At NO time should children under the age of 13 or pets be within 310 cm (10 feet) of the treadmill.
• At NO time should children under the age of 13 use the treadmill.
• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.
• Use the treadmill only for its intended use as described in the TREADMILL GUIDE and OWNER’S MANUAL.
• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.
• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
immersed in water.
• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.
• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair and the like.
• To prevent electrical shock, never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,
bathrooms, car ports or outdoors. Failure to comply may void the warranty.
• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.
• Do not remove the console covers. Service should only be done by an authorized service technician.
It is essential that your treadmill is used only indoors, in a climate-controlled room. If your treadmill has been exposed to colder
temperatures or high-moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before
first time use. Failure to do so may cause premature electronic failure.
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• Never use the treadmill before securing the safety tether clip to your clothing.
• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness or shortness of breath, stop
exercising immediately and consult your physician before continuing.
• When exercising, always maintain a comfortable pace.
• Do not wear clothes that might catch on any part of the treadmill.
• Always wear athletic shoes while using this equipment.
• Do not jump on the treadmill.
• At no time should more than one person be on treadmill while in operation.
• This treadmill should not be used by persons weighing more than specified in the OWNER’S MANUAL WARRANTY SECTION.
Failure to comply will void the warranty.
• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.
• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth
only; never use solvents. (See MAINTENANCE)
• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.
• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock or injury to persons.
• Connect this exercise product to a properly grounded outlet only.
• Do not tip the machine on its side at any time.
WARNING
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the treadmill from the electrical outlet immediately after using, and before cleaning, performing maintenance and putting on or
taking off parts.
DANGER WARNING

67
ASSEMBLY
There are several areas during the assembly process when special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent
damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on a white barcode sticker
on the base frame as shown in this image.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
SERIAL NUMBER:
MODEL NAME: VISION TREADMILL
WARNING
SERIAL NUMBER LOCATION
GROUNDING INSTRUCTIONS
This product must be grounded. If a treadmill should malfunction or break down, grounding provides a path of least resistance
for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with local codes and ordinances.
Connect this exercise product to a properly grounded outlet only.
Never operate product with a damaged cord or plug even if it is working properly. Never operate any product if it appears
damaged, or has been immersed in water. Contact your authorized Vision Fitness retailer for replacement or repair.
WARNING
DANGER
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this
product.
This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit
and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one
circuit. This treadmill should be used with a minimum 20-amp circuit.

8 9
WATE R BOTTLE HOLD ER
GR IP PULSE BARS
QUIC K KE Y (TF40 ONLY)
CONSOLE ( TO UCH CONS OLE SHOWN)
TR ANSPORT WHE EL
ON /OFF SWITCH
CIRCUIT BREAKER
POWER CORD
RE ADI NG R AC K / TABLET HOLD ER
HAND LEBARS
USB P ORT AND I POD® COR D (TOUCH CONSOLE ONLY)
SAFE TY K EY PLACEM ENT
MOTOR COVER
WHEEL LOCK
SI DE R AIL
ROLLER END CAP
RE AR ROLLE R TENSIO N
AND A DJ USTME NT BOLTS
CONSOLE M AST
IN RE ACH CO NTRO LS
BASE FRA ME COVER (TF40 ONLY)
RUNN ING BELT / RUNNING DE CK
SUPP ORT BAR
12
ABOVE FOOT L ATCH
1
2
FOOT LOCK LATCH (UN DERNEATH DEC K)
WATE R BOTTLE HOLD ER
GR IP PULSE BARS
CONSOLE ( TO UCH CONS OLE SHOWN)
TR ANSPORT WHE EL
ON /OFF SWITCH
CIRCUIT BREAKER
POWER CORD
RE ADI NG R AC K / TABLET HOLD ER
HAND LEBARS
USB P ORT AND I POD CORD (TOUCH C ONSOLE ONLY)
SAFE TY K EY PLACEM ENT
MOTOR COVER
SI DE R AIL
ROLLER END CAP
RE AR ROLLE R TENSIO N
AND A DJ USTME NT BOLTS
CONSOLE M AST
IN RE ACH CO NTRO LS
RUNN ING BELT / RUNNING DE CK
SUPP ORT BAR
QUIC K KE Y
TF20
TF40 T40

10 11
TOOLS INCLUDED:
F5 mm T-Wrench
F13 mm Hex Wrench
F4 mm L-Wrench
F5 mm L-Wrench
F6 mm T-Wrench
F8 mm T Wrench
FScrewdriver
PARTS INCLUDED:
F2 Console Masts
F2 Handlebars
F2 Support Bars
F2 Support Bar Caps (T40)
F2 Sets Base Frame Covers
F1 Console Base
F1 Console Base Cover
F1 Water Bottle Holder
F1 Accessory Holder
F1 Hardware Kit
F1 Safety Key
F1 Power Cord
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Once the banding straps have been removed, do not transport this unit unless it is
fully assembled. Unpack and assemble the unit where it will be used. Never grab hold of
any portion of the incline frame and attempt to lift or move the treadmill. Lift the treadmill
from the roller end caps area while a second person removes the parts packed under
the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease, is recommended.
PRE-ASSEMBLY
ALL
MODELS
If you have questions or if there
are any missing parts, contact
your authorized Vision Fitness
retailer.
NEED HELP?
BOLT (A)
20 mm
Qty: 6
SPRI NG WASHE R (B)
8.2 mm
Qty: 6
ARC WASHER (C)
8.4 mm
Qty: 6
T40 HARDWARE FOR STEP 1 :
BOLTS (A)
SPRI NG WASHERS (B)
LEFT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
ARC WASHERS (C)
BASE FRAME
RIGHT CONSOLE MAST
T40 ASSEMBLY STEP 1
NOTE: This step is for T40 models only.
A Open hardware for step 1.
B Attach lead wire to console cable and pull
lead wire through right console mast. After
pulling the lead wire through the mast, the top of
the console cable should be located at the top
of the mast. Detach and discard lead wire.
N
C Attach console mast to base frame using 3
bolts (a), 3 spring washers (b) and 3 arc
washers (c).
D Repeat step C on other side.
NOTE: Do not tighten bolts until step 4 is complete.
NOTE: Do not pinch console cable when placing
the mast onto the base frame.
T40
ONLY
T40 ONLY

12 13
TF20
ONLY
TF40
ONLY
BOLT (A)
20 mm
Qty: 6
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (C)
8.4 mm
Qty: 6
SCREW (M)
20 mm
Qty: 2
SCREW (N)
12 mm
Qty: 4
BOLTS (A)
SPRI NG WASHERS (B)
LEFT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
SCREWS (N)
ARC WASHERS (C)
BASE FRAME
SCREW (M)
BASE FRAME COVER
RIGHT CONSOLE MAST
TF40 ASSEMBLY STEP 1
NOTE: This step is for TF40 models only.
A Open hardware for step 1.
B Slide base frame covers over base frame.
Attach base frame covers using 2 screws
(m) and 4 screws (n).
C Attach lead wire to console cable and pull
lead wire through right console mast. After
pulling the lead wire through the mast, the top of
the console cable should be located at the top
of the mast. Detach and discard lead wire.
D Attach console mast to base frame using 3
bolts (a), 3 spring washers (b) and 3 arc
washers (c).
E Repeat step C on other side.
NOTE: Do not tighten bolts until step 4 is complete.
NOTE: Do not pinch console cable when placing
the mast onto the base frame.
TF40 ONLY
TF40 HARDWARE FOR STEP 1 :
BOLT (A)
20 mm
Qty: 6
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (C)
8.4 mm
Qty: 6
BOLTS (A)
SPRI NG WASHE RS (B)
LEFT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
ARC WASHERS (C)
BASE FRAME
BASE FRAME COVER
RIGHT CONSOLE MAST
TF20 ASSEMBLY STEP 1
TF20 ONLY
TF20 HARDWARE FOR STEP 1 : NOTE: This step is for TF20 models only.
A Open hardware for step 1.
B Slide base frame cover up right console
mast. Attach lead wire to console cable
and pull lead wire through right console
mast. After pulling the lead wire through the
mast, the top of the console cable should be
located at the top of the mast. Detach and discard
lead wire.
NOTE: Do not pinch console cable when placing the
mast onto the base frame.
C Place right console mast over base frame.
D Attach console mast to main frame
bracket using 3 bolts (a), 3 spring
washers (b) and 3 arc washers (c).
NOTE: Do not tighten bolts until step 4 is complete.
E Slide base frame cover up left console
mast. Repeat STEP D to attach left console
mast.
F Slide base frame covers down.

14 15
T40
ONLY
T40 ASSEMBLY STEP 3
BOLT (A)
SPRING WASHER (B)
BOLT (F)
HANDLEBAR
SUPPORT BAR
BASE FRAME
ARC WASHER (E)
SPRING WASHER (B)
ARC WASHER (E)
T40 HARDWARE FOR STEP 3 : NOTE: This step is for T40 models only.
A Open hardware for step 3.
B Attach the right support bar to the base
frame using 1 arc washer (e), 1 spring
washer (b) and 1 bolt (f).
NOTE: Do not tighten bolts until step 4 is complete.
C Attach the right support bar to the
handlebar using 1 arc washer (e), 1
spring washer (b) and 1 bolt (a).
D Repeat on other side.
BOLT (A)
20 mm
Qty: 2
SPRI NG
WASHER (B)
8.2 mm
Qty: 4
ARC
WASHER (E)
8.4 mm
Qty: 4
BOLT (F)
95 mm
Qty: 2
ASSEMBLY STEP 2
BOLT (A)
20 mm
Qty: 6
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (C)
8.4 mm
Qty: 4
FLAT
WASHER (D)
8.2 mm
Qty: 2
HARDWARE FOR STEP 2 :
FLAT WASHER (D)
SPRING WASHER (B)
ARC WASHERS (C)
BOLT (A)
RIGHT HANDLEBAR
CONSOLE CABLES
RIGHT CONSOLE MAST
A Open hardware for step 2.
B Guide console cables from handlebars
through and out of the tops of the console
masts.
C Slide handlebars onto console masts.
D Attach right handlebar to right console
mast using 1 flat washer (d), 1 spring
washer (b) and 1 bolt (a) from the inside and
2 arc washers (c), 2 spring washers (b)
and 2 bolts (a) from below.
E Repeat on other side.
NOTE: Do not pinch console cables while
attaching the handlebars.
T40 SHOWN
ALL
MODELS
T40 ONLY
NOTE: Do not tighten bolts until step 4 is complete.

16 17
TF40
ONLY
TF20
ONLY
TF40 ASSEMBLY STEP 3
FLAT WASHERS (H)
SPRI NG WASHERS (J)
ARC WASHERS (E)
SPRI NG WASHERS (B)
BASE FRAME
SUPPORT BAR
BOLTS (L)
HANDLE BAR
BOLT (A)
TF40 HARDWARE FOR STEP 3 :
NOTE: This step is for TF40 models only.
A Open hardware for step 3.
B Attach the bottom of the support bar to the
base frame using 2 flat washers (h), 2
spring washers (J) and 2 bolts (l).
C Attach the top of the support bar to the
handlebar using 1 arc washer (e), 1
spring washer (b) and 1 bolt (a).
D Repeat on other side.
BOLT (A)
20 mm
Qty: 2
SPRING
WASHER (B)
8.2 mm
Qty: 2
ARC
WASHER (E)
8.4 mm
Qty: 2
BOLT (L)
20 mm
Qty: 4
SPRING
WASHER (J)
6 mm
Qty: 4
FLAT
WASHER (H)
6 mm
Qty: 4
TF20 ASSEMBLY STEP 3
FLAT WASHERS (H)
SPRI NG WASHERS (J)
ARC WASHERS (E)
SPRI NG WASHERS (B)
BASE FRAME
SUPPORT BAR
BOLTS (L)
HANDLE BAR
BOLT (A)
TF20 HARDWARE FOR STEP 3 :
NOTE: This step is for TF20 models only.
A Open hardware for step 3.
B Attach the bottom of the support bar to the
base frame using 2 flat washers (h), 2
spring washers (J) and 2 bolts (l).
C Attach the top of the support bar to the
handlebar using 1 arc washer (e), 1
spring washer (b) and 1 bolt (a).
D Repeat on other side.
BOLT (A)
20 mm
Qty: 2
SPRI NG
WASHER (B)
8.2 mm
Qty: 2
ARC
WASHER (E)
8,4 mm
Qty: 2
BOLT (L)
20 mm
Qty: 4
SPRI NG
WASHER (J)
6 mm
Qty: 4
FLAT
WASHER (H)
6 mm
Qty: 4
TF40 ONLY TF20 ONLY
NOTE: Do not tighten bolts until step 4 is complete. NOTE: Do not tighten bolts until step 4 is complete.

18 19
TF40
ONLY
T40 ASSEMBLY STEP 4
T40
ONLY BOLT (A)
20 mm
Qty: 6
SCREW (G)
12 mm
Qty: 6
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (E)
8.4 mm
Qty: 6
HARDWARE FOR STEP 4 :
ARC WASHERS (D)
SPRI NG WASHERS (B)
SCREWS (G)
MAST
COVERS
CONSOLE
MAST
BASE FRAME
BOLTS (A)
CONSOLE BASE
CONSOLE CABLES
NOTE: This step is for T40 models only.
A Open hardware for step 4.
B Gently place console base on top of
console masts.
C Connect the console cables and tuck
them inside the console masts and slide
console base into console masts.
D Connect the console base to console
masts using 6 arc washers (e), 6
spring washers (b) and 6 bolts (a).
E Attach mast covers to base frame
using 3 screws (g).
F Repeat on other side.
NOTE: Be careful not to pinch the console
cables while attaching the console base.
NOTE: Tighten all bolts from STEPS 1–3.
BOLT (A)
20 mm
Qty: 6
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (E)
8.4 mm
Qty: 6
SCREW (N)
12 mm
Qty: 4
TF40 ASSEMBLY STEP 4
HARDWARE FOR STEP 4 :
ARC WASHER S (D)
SPRI NG WASHER S (B)
BOLTS (A)
CONSOLE BASE
CONSOLE CABLES
CONSOLE MAST
BASE FRAME COVER
SCREWS (N)
BASE FRAME
NOTE: This step is for TF40 models only.
A Open hardware for step 4.
B Gently place console base on top of
console masts.
NOTE: Be careful not to pinch the console
cables while attaching the console base.
C Connect the console cables and tuck
them inside the console masts and slide
console base into console masts.
D Connect the console base to console
masts using 6 arc washers (e), 6
spring washers (b) and 6 bolts (a).
NOTE: Tighten all bolts from STEPS 1–3.
E Attach the base frame covers to the
base frame using 4 screws (n).
T40 ONLY TF40 ONLY

20 21
ALL
MODELS
FLAT WASHERS (H)
BOLT (I)
PRE-IN STALLE D
SCREWS
CONSOLE CABLES
CONSOLE REAR COVER
SPRI NG WASHER (J)
FLAT WASHERS (H)
SUPPORT BAR CAP
SUPPORT BAR
NUT (K)
CONSOLE BASE
CONSOLE
ASSEMBLY STEP 5
FLAT WASHERS (H)
BOLT (I)
PRE-IN STALLE D
SCREWS
CONSOLE CABLES
CONSOLE REAR COVER
SPRI NG WASHER (J)
FLAT WASHERS (H)
SUPPORT BAR CAP
SUPPORT BAR
NUT (K)
CONSOLE BASE
CONSOLE
HARDWARE FOR STEP 5 : A Open hardware for step 5.
B Remove 2 pre-installed screws to
remove console rear cover from the
console.
C Attach the console to the console base
using 2 bolts (i) and 2 flat washers
(h) from above and 2 flat washers (h) 2
spring washers (J) and 2 nuts (k) from
below.
D Connect the console cables to the
console.
E Re-attach the console rear cover to
the console using 2 pre-installed
screws.
F T40 ONLY: Insert support bar caps into
bottom of support bars.
BOLT (I)
45 mm
Qty: 2
NUT (K)
Qty: 2
SPRI NG
WASHER (J)
8 mm
Qty: 2
FLAT
WASHER (H)
8 mm
Qty: 4
NOTE: Be careful not to pinch the console
cables while attaching the console.
T40 ONLY:
TF20
ONLY BOLT (A)
20 mm
Qty: 6
SCREW (M)
20 mm
Qty: 4
SPRI NG
WASHER (B)
8.2 mm
Qty: 6
ARC
WASHER (E)
8.4 mm
Qty: 6
TF20 ASSEMBLY STEP 4
HARDWARE FOR STEP 4 :
BASE FRAME
SCREWS (M)
BASE FRAME COVER
ARC WASHER S (D)
SPRI NG WASHER S (B)
BOLTS (A)
CONSOLE BASE
CONSOLE CABLES
CONSOLE MAST
NOTE: This step is for TF20 models only.
A Open hardware for step 4.
B Gently place console base on top of
console masts.
NOTE: Be careful not to pinch the console
cables while attaching the console base.
C Connect the console cables and tuck
them inside the console masts and slide
console base into console masts.
D Connect the console base to console
masts using 6 arc washers (e), 6
spring washers (b) and 6 bolts (a).
NOTE: Tighten all bolts from STEPS 1–3.
E Attach base frame covers to base
frame using 4 screws (m).
TF20 ONLY

22 23
LIMITED HOME-USE WARRANTY
WEIGHT CAPACITY
T40 = 400 lbs (182 kilograms)
TF40 = 400 lbs (182 kilograms)
TF20 = 375 lbs (170 kilograms)
FRAME
Warranty on the frame against defects in workmanship and
materials for the period specified on the warranty policy from the
date of original purchase, so long as the device remains in the
possession of the original owner. (The frame is defined as the
welded metal base of the unit and does not included any parts
that can be removed.)
DRIVE MOTOR/ELEVATION MOTOR
Warranty on the drive/elevation motors against defects in
workmanship and materials for the period specified on the
warranty policy from the date of original purchase, so long as the
device remains in the possession of the original owner. Labor or
installation of motor is not covered under the motor warranty.
ELECTRONICS & PARTS
Warranty on the electronic components, finish and
all original parts for the period specified on the
warranty policy from the date of original purchase,
so long as the device remains in the possession of
the original owner.
LABOR
Warranty shall cover the labor cost for the repair of
the device for the period specified on the warranty
policy from the date of the original purchase, so
long as the device remains in the possession of the
original owner.
NOTE: For further information on the warranty period, please
refer to the warranty policy along with the equipment.
BOLT (L)
20 mm
Qty: 4
BOLT (M)
20 mm
Qty: 6
ASSEMBLY STEP 6
HARDWARE FOR STEP 6 :
CONSOLE BASE
BOLTS (L)
CONSOLE BASE COVER
HANDLEBAR
BOLTS (M)
WATER BOTTLE HOLDER
A Open hardware for step 6.
B Attach the console base cover to the
console base using 4 bolts (l).
C Attach water bottle holder and
accessory holder to left and right
handlebars using 6 bolts (m).
ASSEMBLY COMPLETE!
This treadmill has a pre-waxed belt and
should never be lubricated. Waxing
the belt can cause damage that is not
covered by the warranty.
IMPORTANT
ALL
MODELS

24 25
EXCLUSIONS AND LIMITATIONS
Who IS covered:
• The original owner and is not transferable.
What IS covered:
• Repair or replacement of a defective motor, electronic component,
or defective part and is the sole remedy of the warranty.
What IS NOT covered:
• Normal wear and tear, improper assembly or maintenance, or
installation of parts or accessories not originally intended or
compatible with the equipment as sold.
• Damage or failure due to accident, abuse, corrosion, discoloration
of paint or plastic, neglect, theft, vandalism, fire, flood, wind,
lightning, freezing, or other natural disasters of any kind, power
reduction, fluctuation or failure from whatever cause, unusual
atmospheric conditions, collision, introduction of foreign objects
into the covered unit, or modifications that are unauthorized or not
recommended by the manufacturer.
• Incidental or consequential damages. The manufacturer is not
responsible or liable for indirect, special or consequential damages,
economic loss, loss of property, or profits, loss of enjoyment or
use, or other consequential damages of whatsoever nature in
connection with the purchase, use, repair or maintenance of the
equipment. The manufacturer does not provide monetary or other
compensation for any such repairs or replacement parts costs,
including but not limited to gym membership fees, work time lost,
diagnostic visits, maintenance visits or transportation.
• Equipment used for commercial purposes or any use other than a
single family or Household, unless endorsed by the manufacturer
for coverage.
SERVICE AND REPAIRS
• Delivery, assembly, installation, setup for original or
replacement units or labor or other costs associated with
removal or replacement of the covered unit.
• Any attempt to repair this equipment creates a risk of injury.
The manufacturer is not responsible or liable for any damage,
loss or liability arising from any personal injury incurred during
the course of, or as a result of any repair or attempted repair
of your fitness equipment by other than an authorized service
technician. All repairs attempted by you on your fitness
equipment are undertaken AT YOUR OWN RISK and the
manufacturer shall have no liability for any injury to the person
or property arising from such repairs.
• The warranty is limited to replacing or repairing, at the
servicer’s and/or manufacturer’s option, the same or
comparable model.
• Replacement units, parts and electronic components
reconditioned to as-new condition by the manufacturer or its
vendors may sometimes be supplied as warranty replacement
and constitute fulfillment of warranty terms.
TREADMILL OPERATION
See TREADMILL GUIDE for instructions on the following:
• LOCATION OF THE TREADMILL
• USING THE SAFETY KEY
• FOLDING THE TREADMILL
• MOVING THE TREADMILL
• LEVELING THE TREADMILL
• TENSIONING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• USING THE HEART RATE FUNCTION
See CONSOLE MANUAL for instructions on the following:
• CONSOLE OPERATION
• CONSOLE DISPLAY INFORMATION
• PROGRAM INFORMATION
• NIKE + IPOD OPERATION
• PASSPORT PLAYER INFORMATION

Vision Treadmills Owner's Manual 082812' | © 2012 Vision Fitness
www.visionfitness.com